Determine the slope and deflection at point B of the beam shown by using double integration method. (10 points) 50 kN-m A В 4 m El = constant E 70 GPa %3D I = 164 (106) mm4

Q: Pick up the incorrect statements from the following: 1. Cast iron pipes are structurally stronger an...

A: From the given statement, find correct statements

Q: to identify a highway mode transportation-related problem. And, what possible

A:

Q: 2. If the cons mponent of

A:

Q: if the distance is (1000) ft and the travel time is (18.9) second, then the . space mean speed is 50...

A: The space-mean speed is the average speed of vehicles traveling a given segment of the roadway durin...

Q: The maximum allowable speed of a car that could travel a circular curve is 85 kph. If the impact fac...

A: Impact factor=V2/gR V=85kph= 85×1000/3600 m/s =23.61 m/s g=9.81 m/s2 R= radius R=23.612/(0.21×9.81)=...

Q: The arched beam in the following figure carres the concentrated vertical forces shown. Determine for...

A: As given in the question ,about the arch beam For calculation of support reaction , Equilibrium cond...

Q: Using Three-Moment Equation, determine the reactions and draw the shear diagram and moment diagram 3...

A: Degree of indeterminacy = 4. Hence, 4 equations are required to solve moments.   Steps for Analysis:...

Q: dius of 120m and has an angle of 9.31° from the horizontal. The center of gravity of the car is loca...

A:

Q: The 'Euler' load for a column is 1000 kN and crushing load is 1500 kN. The 'Rankine' load is equal t...

A:

Q: Determine the present worth of the following cash flows based on an interest rate of 6.01% per year,...

A:

Q: Determine the present worth of the following cash flows based on an interest rate of 7.66% per year,...

A:

Q: What will be the discharge of a single- cutting pump, if it has one cylinder of area 0.5 m2, and str...

A: Given data: Cylinder area, A = 0.5 m2 Stroke length, l = 10 cm = 0.1 m Speed, N = 120 rpm

Q: Determine the maximum deflection for the beam shown by the moment-area method.

A:

Q: In a data set of annual maximum rainfall with average of 250mm and standard deviation of 40mm: The p...

A:

Q: Which of the following cannot be considered as technology or technology was not applied? I. Water ...

A: The main processes in a water refilling station is dictated by raw water quality. The typical steps ...

Q: Given data: Degree of saturation%3D0.45 Void ratio=0.25 Specific gravity%=D2.7 Find water content

A:

Q: How many studs are require for the exterior wall on the main floor if there are two doors and 6 wind...

A: Hi! Thank you for the question As per the honor code, We’ll answer the second and third question sin...

Q: 10 kN/m B 2 m 4 m 450 Determine the horizontal and vertical component of raction at he pins A,B.C

A: To find reaction at A,B,C

Q: A small funnel in the shape of a cone is being emptied of fluid at the rate of 15 cubic centimeters ...

A: Given values,  rate of flow = 15 cubic centimeters per second  height of the funnel = 23 cm radius a...

Q: An aircraft manufacturer uses 1,000,000 special rivets per year at a uniform rate. The rivets are ma...

A:

Q: 15. A vehicle is moving down at a speed of 80 kph along an inclined surface (G = 2%). If the coeffic...

A:

Q: Consider the drawing below. What is the minimum coefficient of friction at E so that the truss is st...

A: Coefficient of friction: The resistance of the moving body with respect to the surface is known as C...

Q: rigid pavement is to be used to carry a wheel load of 58.77 kN. Enough dowels will be used across th...

A: Load=58.77kN Stress=1.45MPa

Q: A steel rod of circular section tapes from 2 cm diameter to 1 cm diameter over a length of 50 cm. If...

A:

Q: Determine the present worth of the following cash flows based on an interest rate of 7.43% per year,...

A:

Q: A 19 inches square steel bearing plate lies between an 8 inches diameter wooden post and a concrete ...

A:

Q: 3. Solve the a) slope at C and b) deflection at B using either AMM or DIM. Use of direct formulas no...

A:

Q: 1. The floor crane is used to lift 600-kg concrete pipe. Determine the resultant internal loading on...

A: We have to determine the resultant internal loading on the cross section at H as per the given data ...

Q: A rigid pavement is to be used to carry a wheel load of 54.04 kN. Enough dowels will be used across ...

A: Load(W)=54.04kN Strength of concrete (f)=1.52MPa

Q: What will be the discharge of a single- cutting pump, if it has one cylinder of area 0.5 m2, and str...

A: Discharge through the reciprocating pump: The discharge through a single acting reciprocating pump i...

Q: vehicle is moving down at a speed of 80 kph along an inclined surface (G = 2%). If the coefficient o...

A:

Q: A girl is flying a kite, which is at a height of 120 feet. The wind is carrying the kite horizontall...

A:

Q: the depth z a

A: Given data: The load on the soil mass is,P = 100 kN At depth 'z' the stress increment = 10 kN/m2 The...

Q: A 9-m length of 6-mm-diameter steel wire is to be used in a hanger. It is observed that the wire str...

A: Given data : Modulus of elasticity E=200 GPa Elongation ∆L=18 mm Length of wire L=9 m Diameter of wi...

Q: (Airy Stress Function) Consider the following rectangular plate. a (a) Determine stress components (...

A: Solution -(a) The airy stress function is given below,ϕ=px3yFor σxx=∂2ϕ∂y2∂ϕ∂y=px3∂2ϕ∂y2=0=σxxFor σy...

Q: w = 14 kN/m, ME 3 kNm, and RA = 7.92 kN w kN/m MẸ kNm в A B C D E 0.8m 1.0m 0.7m 2.0m RA M(x) cut

A:

Q: Compute the peak hour factor if the hourly volume of traffic is 1969 veh/hour and the highest 15-min...

A: Given data, Hourly volume of traffic = 1969 veh/hr Peak 5 min volume = 737 vehicle To find out the p...

Q: The probability of T=100 year to occur within the next 50 years is?

A:

Q: Load-Shear and Shear-Moment Relationships Requirements 1A. Reactions at the supports 1B. Shear diagr...

A: RA + RC  = 40 + 16X3  RA + RC = 88 Moment diagram  40 x 1 +15 - 16 x 3 x 4.5 + Rc x 5 =0 Rc = 32.2 k...

Q: A rigid pavement is to be used to carry a wheel load of 57.62 kN. Enough dowels will be used across ...

A: Load=57.62kN Stress=1.32MPa

Q: The peak magnitude of 4 hr direct runoff hydrograph over a catchment area is 300 m3/s. The effective...

A:

Q: In a permeability test conducted on a soil with e = 0.50 the discharge velocity was found to be 2.4 ...

A:

Q: Which type of formwork uses pans as forms? O Waffle slab formwork O Wafer slab formwork O Falsework ...

A:

Q: A cylindrical tank with its axis vertical is 1.0 m diameter and 3.6 m high. It is held together by t...

A:

Q: 2. Use the moment area theorems and determine the slope and displacemen B. E- 200 GPa, I= 6 x 10° mm...

A:

Q: The probability in percent of a 150 year return period not to occur within the next 45 years is?

A:

Q: determine the degree of the circular curve. if the maximum allowable speed of a car that could trave...

A: Impact factor=0.17 Speed=85kph

Q: In a particular material, if the modulus of rigidity is equal to the bulk modulus, then the Poisson'...

A:

Q: Use the force method (method of consistent distortions) to find the value of the redundant force ind...

A: We have to determine the value of redundant NDB as per the given data in the question and using the ...

Q: · A cantilevered beam is part of an assembly machine and is made of steel with round cross section (...

A: Given 400lbf= 1780N

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.