Determine the smallest force P, applied to the plunger D, that will prevent the couple C = 250 N-m from moving the cylinder. Friction may be neglected at all surfaces, except between the plunger and cylinder. The masses of the bodies are negligible. Hs = 1.6 250 KN-m 40 m 30 B 30" 13.25 KN c. 10.000 KN a. b. 6.25 KN d. 3.906 KN

Determine the smallest force P, applied to the plunger D, that will prevent the couple C = 250 N-m from moving the cylinder. Friction may be neglected at all surfaces, except between the plunger and cylinder. The masses of the bodies are negligible. Hs = 1.6 250 KN-m 40 m 30 B 30" 13.25 KN c. 10.000 KN a. b. 6.25 KN d. 3.906 KN

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter14: Sheet-pile Walls

Section: Chapter Questions

Problem 14.5P

See similar textbooks

Similar questions

In the cage system below; It is under the effect of a P=250 kN load acting at an angle of θ=30° from the point C. Calculate the horizontal displacement (cm) to the right at point C. (E=2000 kN/cm² and A=50 cm² will be taken for all bars.)
A rectangular plane, 1.2 m by 1.8 m is submerged in water and makes qn angle of 30° with the horizontal, the 1.2 m sides being the horizontal. a. what is the minimum lressure acting on the plane in kPa b. what is the maximum lressure acting on the plane kPa c. Determine the magnitude of hydrostatic force acting on either side of the plane in KN. Support your computations with correctly drawn and labrled pressure prism diagrams.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
2. 2. A rectangular pontoon 10 m by 4 m in plan, weighs 280 KN and floats in sea water of density 1025 kg m−3. A steel tube weighing 34 KN is placed longitudinally on the deck. When the tube is in a central position, the center of gravity for the combined mass is on the vertical axis of symmetry 0.25 m above the water surface. Find a) the metacentric height, and b) the maximum distance the tube may be rolled laterally across the deck if the angle of heel is not to exceed 5° c) Justify with complete illustration.
Find the elongation of a bar where diameter 100mm under the action of axial force of 40kn length of the bar is 2m and E= 2×108 kn/m2
the inclined circular (D = 4.06 m) gate shown below retains a liquid with Sg = 3.35 on one side. the vertical distance from the liquid surface to the top of the gate, h, is 2.42 m. use 39 degrees. determine the hydrostatic force (kN0 acting on the gate.
Application of Equilibrium Solve for the value of unknown variables Given : P1 = 10KN W1 = 5 KN/m P2 = 6 KN W2 = 10 KN/m θ= 58° a.Unknowns: RAy , RBy , RBx , MB b. compute the internal shear 1.35 m to the right of support A
Determine the horizontal and vertical component of the total hydrostatic force (kN) the oil exerts on the face AB of the overhang if it is 1.31 m long. Oil is 0.8
The block A and the wedge B weighs 100 kN and 40 kN, respectively. The coefficient of fritction for all contacting surfaces is µ = 0.268. Determine the following: a. What value of P in kN would be required to push to the right the wedge under the block? b. What value of P in kN would be required to pull to the left the wedge under the block? Assume the block A is stll in contact with the wall just as motion starts.
Compute the value of EIy at 2.5 m from the left support.
c. Slope at L/3. d. Deflection at L/3
Determine the vertical displacement of node A. Consider EA = 16x104 [kN-m]