Determine the stresses for each segment when the temperature of the rigid bar is -45 degrees celsius. A close fit exists at both of the rigid supports when the temperature is 24 degrees celsius. Use E= MN GPa and Coefficient of thermal expansion is 11.7 x 10^-6 per degrees Celsius. ... 750 mm? 380 mm? 300 mm 300 mm

Determine the stresses for each segment when the temperature of the rigid bar is -45 degrees celsius. A close fit exists at both of the rigid supports when the temperature is 24 degrees celsius. Use E= MN GPa and Coefficient of thermal expansion is 11.7 x 10^-6 per degrees Celsius. ... 750 mm? 380 mm? 300 mm 300 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If P = 8.571 kN, determine the stress in member CE assuming that the area in steel is 24 mm^2. *DRAW THE FREE BODY DIAGRAM *COMPLETE SOLUTION *3 decimal places ALL ANSWER
4.15 Knowing that for the casting shown in the figure the allowable stress is 6 ksi in tension and 15 ksi in compression, determine the maximum couple M that can be applied.
STRENGTH OF MATERIALS (NO LONG EXPLANATION NEEDED) PLEASE WITH FBD! RATE WILL BE GIVEN For the given system below, rods A and B support the rigid bar, pinned at O, as it is subjected to load P = 40 kN. The rods are identical except for their lengths. Find the (a) stress in rod A if its cross-sectional is 300mm2 (b) If rod A elongates by 2mm, how much is the elongation of rod B?
The single rope of a cantilever crane supports a load of 200 kN and passes over two pulleys and then vertically down the axis of the crane to the hoisting apparatus. The section AB of the crane is a hollow rectangle. The outside dimensions are 37.5 cm and 75 cm and the material is 2.5 cm thick all round, and the longer dimension is in the direction AB. Calculate the maximum tensile and compressive stresses set up in the section, and locate the position of the neutral axis. (Cambridge) ANSWER: tensile 155 MN/m2, compressive 147 MN/m2; neutral axis 0.365 m from outside of box-section Please show the solution to get the answer.
The following beam is supported by three cables AD, BE, and CF. Cables AD and CF are made of steel, and cable BE is made of aluminum. The data is presented in the table. A force P of 125 kN is applied, and the temperature increases by 100°C. Determine: The stress in each cable. Answ: 25.09 MPa, 49.22 MPa. The vertical displacement of the beam. Answ: 1.99E-3 m.
A vertical steel bar ABC is pin-supported at its upper end and loaded by a force P1 at its lower end. A horizontal beam BDE is pinned to the vertical bar at joint B and supported at point D. Load P2 and moment M are applied at end E. Calculate the vertical displacement δC at point C if the loads are P1 = 2.5 kip, P2 = 1 kip, and M = 25 kip-in. The modulus of elasticity is E = 29,000 ksi and crosssectional areas are A1 = 0.25 in2 A2 =0.15in2 .Ignore the weight of the bar.
Need answer ASAP. Please be detailed and clear with your solution. II. Shown is a parabolic segment submerged vertically in water. W.S. 3 m 60 cm 3 m vertex 1) Determine the magnitude of the total force on one face of the area, in kN. * 2) Determine the location of the total force from the W.S. *
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P = 1920 N, T = 4044 Nm, a = 0.81 m, b = 1.11 m, c = 0.98 m, w = 37 mm, and h = 73 mm. Round off the final answer to one decimal place.
Determine the largest weight “W” that can be supported by the two wires AB and AC. The working stresses are 100MPa for AB and 150MPa for AC. The cross sectional area of AB and AC are 400mm2 and 200mm2.
Calculate the required amount of reinforcement (in in2) considering the ultimate moment below. Use english units. Note: Use the following equations for minimum reinforcement in English units. Pmin for flexure = (3*sqrt (f'c))/fy greater than or equal to 200/fy f'c = 3000 psi fy = 40 ksi Mult = 200 ft-k
Which of the following is the nearest value for the force at member AC? a. 3.4 kN tension b. 3.4 kN compression c. 1.7kN compression d. 1.7kN tension
The 919-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 321 mm2. Find the location x (in mm) of P that can be safely applied to the bar if the stresses in AC and BD are limited to 112 MPa and 57 MPa, respectively. Express your answer in two decimal places.