Determine the tensile development length required for the uncoated #8 bars shown if normal weight concrete and 180° hooks are used. f'c = 4000 psi and fy = 60000 psi. - 21" - 3 @ 5" 4 #8 W3 stirrups @ 6" 0.C. 27 30

Determine the tensile development length required for the uncoated #8 bars shown if normal weight concrete and 180° hooks are used. f'c = 4000 psi and fy = 60000 psi. - 21" - 3 @ 5" 4 #8 W3 stirrups @ 6" 0.C. 27 30

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the section shown in Fig. P.4.1b, find the volumetric ratio of spiral which will make the…

A: Volumetric ratio = 0.45 (Ac/Ack-1) (fck/fy) Ac=196349.5 mm2 Ack=159043 mm2 VR =…

Q: Assume wet concrete (gamma=150lbf/ft3) behaves as a liquid. Determine the force per unit foot of…

A: Given information:Given that

Q: 5. Design a rectangular reinforced concrete beam to resist service moments of 195 kNm from dead…

Q: A rectangular beam 350 mm wide and effective depth of 500 mm is to be designed as subjected to an…

Q: A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy =…

A: Given data f'c = 26.27mpa fy = 414 mpa The As value was not given. so lets assume as 3bars of 32mm…

Q: For the section shown, use Whitney's rectangular block to calculate a, ß1 and c, determine the…

A: Given Data:fc=400psiEC=3600ksiand Grade 60 steel fy=60000psiEs=29000 ksi

Q: A concrete post is reinforced with 4-28mm diameter steel bars. Compute the stress in each material…

Q: A singly reinforced rectangular beam 300 mm wide and 600 mm deep is subject to a factored shear…

Q: A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 27.63 MPa and fy =…

A: Answer We are given f'c = 27.63 Mpa fy = 414 Mpa b = 475 mm d = 685 Mpa t = 138 mm = web…

Q: Two wooden members, each having a width of b = 3.9 in. and a depth of d = 1.3 in., are joined by a…

Q: Calculate yield moment for the beam. Assume concrete accepts no tension. Use fc' = 4000 psi and =…

Q: Two wooden members, each having a width of b = 6.9 in. and a depth of d = 2.3 in., are joined by a…

Q: 1) Examples of standard steel shapes include? a) Brick, CMU, concrete block b) Z-ties, corrugated…

Q: Awall form 14 ft high is filled with 160 lb per cu ft concrete at a tem perature of 70°F. The…

Q: Compute for the FS against sliding and overturning. SG concrete= 24, µ=0.6. Consider UF. Refer to…

A: The design of a dam is done taking into consideration many different forces. These forces include :…

Q: In the column shown, the lower column bars are #8 and the upper ones are #7. The bars are enclosed…

Q: or the floor system shown below kN/m, Answer the following: Classify the floor system into one Check…

Q: Two wooden members, each having a width of b = 6.0 in. and a depth of d = 2.0 in., are joined by a…

Q: A simply supported beam 300 mm wide, 500 mm deep and spans 5.9 m supports a service super imposed…

A: This question is related to the Design concrete structure.

Q: 3. Determine the following using the floor layout below. Assume this is an upper story in a…

A: As per Bartleby's guidelines we are supposed to answer only first 3 sub parts. Kindly repost other…

Q: 3. A column shown below has tie reinforcement conforming to ACI 25.7.3. Assume normal- weight…

A: Given: concrte stress fc'=6000 psi allowed stress in concrete fc=60002=3000 psiand for steel grade…

Q: square footing 2.4 m x 0.32 m thick supports a 300 mm square column at its center. Column loads are…

Q: A rectangular beam having a width of 304.8 mm and an effective depth of 495.3 mm is reinforced with…

A: Given: The width of the beam is 304.8 mm. The effective depth is 495.3 mm. The area of steel bars is…

Q: 3) Concrete achieves its full strength after a day period? a) 45 b) 28 c) 7 d) 3 4) #8 Resteel has a…

A: ASKED: To complete the given statement using the given options. Given statement: Concrete…

Q: A rectangular footing 2.1 m x 3.6 m x 0.35 m thick supports a 300 mm square column at its center.…

Q: singly reinforced rectangular beam 300 mm wide and 600 mm deep is subject to a factored shear force…

A: For light weight concrete lambda is equal to 0.75

Q: for rectangular reinforced Con crete sectim t h= 680MMg d=600mm, b= 330mm, As = 6$16mm fx=22 MP ,…

A: Solution Given data: Dimension of rectangular reinforced section: Height(h)=680 mm effective…

Q: am. Calculate the required nominal shear strength (kN) of 10-mm-dia. the stirrups if lightweight…

A: Given:- b=300mm d=600mm Vu=370kN centroid=70mm 10mm diameter concrete strength=25MPa To find:-…

Q: A cantilever beam is reinforced with 4-#9 epoxy coated reinforcing bars, determine the length…

A: Hi there!! since you have asked multiple questions, we will solve the first question for you. If you…

Q: Calculate the concrete compression force, C., Eq. (4-13b).

A: Introduction : The capacity of concrete to withstand loads before failure is known as compressive…

Q: 2. Problem 4: Calculate the nominal strength of the section. 2.25 f 3,000 psi 2.50" #9 BARS Grade 60…

Q: A singly reinforced rectangular beam 300 mm wide and 600 mm deep is subject to a factored shear…

Q: 6. Determine the minimum required dimension 948 ba/ft distnbuted load (d) of the square concrete…

Q: Determine the required reinforcement for T- section beam to resist torsion T = 11.75 KN.m with the…

A: Moment of resistance = 0.87 fy Ast [ d-0.42 xu] moment of resistance for high yield reinforcement =…

Q: Problem 2.5 A reinforced concrete beam section is 375 mm wide and 500 mm deep. The beam camies…

Q: Calculate DOl and identify the following structure as determinate,

A: DOI HAS TO CALCULATE OF THE FRAME GIVEN

Q: SHOW CLEAR SOLUTIONS (STEP BY STEP). USE NSCP 2015. uaume a concrete cover of 40mm, 10mm stirrups…

Q: A rectangular footing 2.1 m x 3.6 m x 0.35 m thick supports a 300 mm square column at its center.…

Q: For pretensioned axially tensioned member, how to calculate the effective prestress established in…

A: Calculation of the Effective Prestress in the Concrete : 1. The stress remaining in the concrete due…

Q: altermate design pad of 30 kN/m, under the following conditions: concrete unit weight, Yc = 23.5…

A: Given: L=4m, Deadload=25 kN/m, Liveload=30kN/m fc'=28 MPa, fy=420 MPa db=32 mm

Q: Given multi story building of 20 x 20m area as shown in the sketch, design the slabs according to AC…

A: Given data Multi-story building of 20 x 20m area Assume that the ultimate compression strength of…

Q: A reinforced concrete beam has a total depth of 700 mm. Use f'c=34 MPa and fy=415 Mpa. The diameter…

A: Given Data b=350mm, d=550+150-60-802=600mm c=600d600+fy=600×600600+415=354.68mm…

Q: A 500-N concrete block is to be lifted by the pair of tongs shown. 500 N 45 mm T45 mm 90 mm 90 mm A…

Q: A reinforced concrete column measuring 12 in. x 16 in. is subjected to axial forces and momer that…

A: Solution; Given Data; from the particular point on the interaction diagram. It is given the ratio of…

Q: Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft3) behaves as a liquid. Determine the…

Q: Design the vertical stem of a T-shaped retaining wall for a height of 3 m above the ground level.…

Q: 2. Determine the design moment capacity of the beam in positive bending. = [m] kN∙m (whole number)

A: Given Data:b=250mmd=500mmReinforcement: bottom= 4-20mmd'=80mmtop = 2-16mmd'=70mmfc=21 mpafor 20mm…

Q: A typical grade beam 300 x 800 is reinforced with 2- 25M bars and the cover is forconcrete cast and…

A: D (overall depth) = 800mm d' (effective cover) = 60mm d (effective depth) = 740mm b (width) = 300mm…

Q: pelow. Confirm that the cross section conforms to ACI Code. Assume normalweight concrete, f= 4000…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

Determine the tensile development length required for the uncoated #8
bars shown if normal weight concrete and 180° hooks are used.
f'c = 4000 psi and fy = 60000 psi.
21"-
3 @ 5"
3"
= 15"
4 #8
#3 stirrups
@ 6" O.C.
27 30

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

b) Using first principles analyze a rectangular beam for having 230 mm width and 550 mm effective depth is reinforced with steel An on tension side only. Taking parameters with the usual notation as k = 0.36, k2 = 0.42 and Eru = 0.0035 determine for concrete of grade M2s and steel of grade Feso obtain. Xu mar, Mur max, As max for balance section; Mur for Au = 800 mm?:
A rectangular footing 2.1 m x 3.7 m x 0.32 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 373 kN LL = 287 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the ultimate punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
Assume wet concrete (gamma=150lbf/ft3) behaves as a liquid. Determine the force per unit foot of length exerted on the forms. If the forms are held in place as shown, with ties between vertical braces spaced every 2ft, what is the force exerted on the bottom tie?
30 A rectangular footing 2.3 m x 3.2 m x 0.34 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 341 kN LL = 216 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA.
Q: a) State the proper procedure for filling the concrete cylinder? b) If the peak load of concrete cylinder in compression is 70,000 pounds, find the crushing strength of concrete? (Hint: concrete cylinder dia is 6in). SIR, PLS GIVE ME PROPER AND CORRECT ANSWER WITH FULL DETAILS. THANKS
5 A square footing 2.4 m x 0.35 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 372 kN LL = 293 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the maximum ultimate bending moment in the slab. Write your final answer as whole number with the unit of kN-m.
a rectangular footing 2.3 m x 3.3 m x 0.31 m thick supports a 300 mm square column at its center. column loads are service conditions:DL = 385 kN LL = 292 kN f'c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm calculate the nominal punching shear stress in the slab. write your final answer with 2 decimal places if the unit is MPA.
A rectangular footing 2.1 m x 3.6 m x 0.35 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL = 346 kN LL = 231 kN f’c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA. Answer: 1.83
Design a 1 way slab to carry a live load of 4.8 KPa on a simple span of 4.50 m. Use f'c = 20.70 MPa, fy = 275 MPa and unit weight of concrete 23.56 KN/cu m. Use 2015 NSCP specifications Draw/sketch your final output with proper labeling of reinforcements/temperature bars
a square footing 2.4 m x 0.34 m thick supports a 300 mm square column at its center. column loads are service conditions:DL = 376 kN LL = 213 kN f'c = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm calculate the nominal one way shear stress in the slab. write your final answer with 2 decimal places if the unit is MPA.
1- For the floor system shown in Figure below, support service live load 4KN / (m ^ 2) and service dead load 5KN / (m ^ 2) Answer the flowing. Classify the floor system into one way or two-way solid slab. 2- What is the minimun slab thickness that should be used to control deflection and shear requirement ? 3- By using Ø 12 mm rebar, what is the required positive and nagative reinforcement? 4- Sketch the detail of reinforcement. Use : fy = 400Mpa , f c ^ prime =30 Mpa 6.00 m 6.00 m6.00 m 3.00 m 0.30 m АB 3.00 m 3.00 m
A rectangular footing 2.3 m x 3.6 m x 0.38 m thick supports a 300 mm square column at its center. Column loads are service conditions: DL= 306 kN LL = 241 kN Li Pc = 21 MPa fy = 415 MPa Concrete cover to the centroid of steel reinforcement = 100 mm Calculate the nominal punching shear stress in the slab. Write your final answer with 2 decimal places if the unit is MPA