Determine the total power required for individual compressors for evaporator loads of 20 tons at 24ᵒF, 30 tons at 34ᵒF and 10 tons at 44ᵒF for an ammonia vapor compression system. Condensing temperature is 104 ᵒF.

Determine the total power required for individual compressors for evaporator loads of 20 tons at 24ᵒF, 30 tons at 34ᵒF and 10 tons at 44ᵒF for an ammonia vapor compression system. Condensing temperature is 104 ᵒF.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 2RQ: The operating condition for the single compressor in a household refrigerator is the lowest box...

See similar textbooks

Similar questions

Condensers in these refrigerators are all_______cooled.
What are the approximate temperature ranges tor low-, medium-, and high-temperature refrigeration applications?
The operating condition for the single compressor in a household refrigerator is the lowest box temperature, which is typically A. 0F B. -20F C. 20F D. 40F
When the outside ambient air temperature is 90F, the temperature of the condensing refrigerant in a standard- efficiency unit should be approximately A. 120F. B. 130F. C. 140F. D. 150F.
The following data were obtained from a performance test of a 10 x 9-cm single acting, water jacketed two-stage air compressor: Pressures: Atmospheric, 102 kPaa; leaving first-stage, 634 kPaa; leaving second-stage, 4.20 MPa. Temperatures: Atmospheric, 240C; leaving first-stage, 1080C; entering 2nd stage, 250C; leaving 2nd stage, 1270C Compressor speed, 648 rpm Power input to motor, 5.65 kW Motor and belt efficiency, 81.5% The following are calculated from test data: Air flow rate, 0.387 ??⁄??? Compression exponents: 1st stage 1.15; 2nd Stage, 1.2 Calculate: a) Approximate indicated power b) Power for isothermal compression c) Shaft power d) 1st stage piston displacement e) Actual volumetric efficiency f) Isothermal compression efficiency g) Mechanical efficiency based on the approximate indicated power h) Over-all efficiency of the compressor
Thermodynamics Answer the following problem with complete solutions. Write legibly Refrigerant HFC-134a is ideally throttled from an enthalpy of 480 kJ/kg at the evaporator pressure of 0.20 MPa to a pressure of 0.02 MPa. What is the final enthalpy?
The following data for the R-12 refrigeration system as shown are as follows: Evaporator 1 0 OC 30 TOR Evaporator 2 -10OC 20 TOR Evaporator 3 -20OC 10 TOR Condenser 20OC Assume simple saturation and isentropic compression and determine the following: a) Draw the h-s diagram b) The refrigerant flow in each evaporator c) Total work of compression, WC in kW d) Heat rejected in the condenser, QR in kj/min e) Coefficient of performance
A refrigeration system using refrigerant 12 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature is -15°C and the condensing temperature 30°C. At the entrance to the evaporator, what is the fraction of vapor in the mixture expressed on a mass basis? 0.97 0.29 0.92 0.27
In a steam power plant, the condenser pressure is 10 kPa. The turbine and pump isentropic efficiencies are both 85 %. Draw the schematic and T-S diagrams. Label the points by setting point 1 at the condenser outlet, point 2 at the pump outlet, point 3 at the boiler outlet, and point 4 at the turbine outlet. Use the label 2a and 4a for the points due to the isentropic efficiency of the pump and turbine, respectively. Use 2 decimal places for the enthalpy and other energies in solving and for the final answers. For the steam quality (x) and entropy (s), use 4 decimal places in solving. For the specific volume, use 6 decimal places. The pressure and the temperature of steam that enters the turbine are 4.5 MPa and 800 oC Determine the following: (INPUT YOUR ANSWERS ON THE BLANK SPACES PROVIDED.) Enthalpy at point 1 in kJ/kg = Enthalpy at point 2 in kJ/kg = Enthalpy at point 3 in kJ/kg = Enthalpy at point 4 in kJ/kg = Actual Enthalpy at point 2a in kJ/kg = Actual Enthalpy at point…
In a steam power plant, the condenser pressure is 10 kPa. The turbine and pump isentropic efficiencies are both 85 %. Draw the schematic and T-S diagrams. Label the points by setting point 1 at the condenser outlet, point 2 at the pump outlet, point 3 at the boiler outlet, and point 4 at the turbine outlet. Use the label 2a and 4a for the points due to the isentropic efficiency of the pump and turbine, respectively. Use 2 decimal places for the enthalpy and other energies in solving and for the final answers. For the steam quality (x) and entropy (s), use 4 decimal places in solving. For the specific volume, use 6 decimal places. The pressure and the temperature of steam that enters the turbine are 4 MPa and 700 oC (use the given values assigned on your name in the table below) Determine the following: Enthalpy at point 1 in kJ/kg= Enthalpy at point 2 in kJ/kg = Enthalpy at point 3 in kJ/kg = Enthalpy at point 4 in kJ/kg = Actual Enthalpy at point 2a in kJ/kg= Actual Enthalpy at…
The condensing and evaporating pressures in a 10 TR R-22 refrigeration system are 11.82 bar and 1.64 bar, respectively. The refrigerant enters the compressor at dry and saturated state and leaves the condenser subcooled by 10°C. The actual COP is 70% of its theoretical value. Determine the condenser temperature in °C. Determine the evaporator temperature in °C. Determine the subcooling temperature in °C. Approximating the operating temperatures to the nearest whole number, determine the heat rejected in kJ/kg. Approximating the operating temperatures to the nearest whole number, determine the mass flowrate of the refrigerant in the system. Approximating the operating temperatures to the nearest whole number, determine the power requirement of the system. Approximating the operating temperatures to the nearest whole number, determine the theoretical COP of the system. Approximating the operating temperatures to the nearest whole number, determine the Actual COP of the system.
What is the function of a refrigeration unit in condensing systems?