Determine the values of the current flowing through each of the resistors on the circuit below. R1 20 22 + Supply 10 V ww R3 55 Ω ww R2 32 22 + Supply 20 V 2. A 400 Volts, 50 Hertz, single phase load draws 50 kVA at a power factor of 0.90 lagging. Determine the following: a) the current and the active power in kW that the load absorbs b) the angle between the source voltage and the load current c) the amount of reactive power necessary to correct the load power factor to 0.98 lagging d) the current the load draws at 0.98 power factor 3. A PhlashSpeed™M WIFI router that is not playing still uses 10 Watts of power. What is the current into this equipment if it is plugged into a standard 220 Volts outlet?

Determine the values of the current flowing through each of the resistors on the circuit below. R1 20 22 + Supply 10 V ww R3 55 Ω ww R2 32 22 + Supply 20 V 2. A 400 Volts, 50 Hertz, single phase load draws 50 kVA at a power factor of 0.90 lagging. Determine the following: a) the current and the active power in kW that the load absorbs b) the angle between the source voltage and the load current c) the amount of reactive power necessary to correct the load power factor to 0.98 lagging d) the current the load draws at 0.98 power factor 3. A PhlashSpeed™M WIFI router that is not playing still uses 10 Watts of power. What is the current into this equipment if it is plugged into a standard 220 Volts outlet?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A substation rated 1250 kVA is operating at full-load at 0.8 pf lagging and to carry anadditional load of 170 kW at 0.85 pf lagging. With the mentioned power factor, thesubstation is experiencing inefficient electrical system: high power losses, high voltagedrops in the electrical equipment, and high electricity bill. To reduce power losses and toreduce the electricity bill, power factor correction is to be of high importance andconsideration. With this condition, the substation is considering of two alternatives namely:Alternative A: To increase the capacity of the substationAlternative B: To add shunt power capacitor In this regard, the owner requested to prepare a summary report consisting of thefollowing details: additional substation capacity in kVA
A network is supplied by a 120 V rms, 60-Hz voltage source. An ammeter and a wattmeter indicate that 12 A rms is drawn from the source and 800 W are consumed by the network. Determine: a. The network power factor b. The network phase angle c. The network impedance d. The equivalent resistance and reactance of the network
A SUBSTATION RATED 1250 KVA IS OPERATING AT FULL LOAD AT 0.8 PF LAGGING AND TO CARRY AN ADDITIONAL LOAD OF 170 KW AT 0.85 PF LAGGING. WITH THE MENTIONED POWER FACTOR, THE SUBSTATION IS EXPERIENCING AN INEFFICIENT ELECTRICAL SYSTEM: HIGH POWER LOSSES, HIGH VOLTAGE DROPS IN THE ELECTRICAL EQUIPMENT, AND HIGH ELECTRICITY BILLS. TO REDUCE POWER LOSSES AND TO REDUCE THE ELECTRICITY BILL, POWER FACTOR CORRECTION IS TO BE OF HIGH IMPORTANCE AND CONSIDERATION. ANSWER: CITE A STEP BY STEP SUMMARY OF HOW TO DETERMINE THE POWER FACTOR CORRECTION REQUIRED IN THE GIVEN PROBLEM TO ARRIVE AT THE ALTERNATIVE THAT SHALL BE SYSTEMATICALLY CARRIED OUT TO GUARANTEE A SUCCESSFUL DECISION IMPLEMENTATION,
A) the current supplied by the source B) the impedance seen at the supply (HV side) C) the power dissipated by the tube D) the operating power factor of the fitting E) using a scale phaser, prove your answers and evaluate each technique for determining circuit power factor.
A substation rated 1250 kVA is operating at full load at 0.8 pf lagging and to carry an additional load of 170 kW at 0.85 pf lagging. With the mentioned power factor, the substation is experiencing inefficient electrical system: high power losses, high voltage drops in the electrical equipment, and high electricity bill. To reduce power losses and to reduce the electricity bill, power factor correction is to be of high importance and consideration. In this regard, the owner requested to prepare a summary report consisting of the following details: A rightful power phasor diagram.
Problem : In the case of an industrial load with a power factor of 0.707 lagging, consuming 100 kW, and the line voltage at 60 Hz is 480Vrms, with a line resistance of 0.1Ω between the power company's transformer and the load, calculate the amount of power saved if the load's power factor changes to 0.94 leading. The answer is "3.771 Kilo-Watt has been saved" and also I want to know the concept of 'Power Factor'.
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
A microwave with ratings shown in Figure 2 is being supplied with a single phase 120 VAC, 60 Hz source. 1. Find the instantaneous current drawn from the source when plugged in. 2. Find the equivalent impedance of the microwave as seen by the source. 3. Find the reactive power supplied by the source and draw the power triangle showing all power components. 4. Determine the type and value of component required to be placed in parallel with the source to improve the power factor to 0.95 leading.
q1: Discussion of power quality aspects that need to be considered before installing the power factor correction unit
A 15 KVA closet transformer lovated inside a building is used to step down the voltage for the buildinh. It is connected to a primary "Z800" V AC power source. The ratio of the number of primar windings to the number og secondary windings on the transforemer is 60 to 15. 1. what is the voltage provided to the building? 2. What is the amoung of current provided to the building? 3. If the building consymes 3200W of power, what is it's power factor? 4. What is the phase angle of the secondary power source in the building?
Perform the following steps for the given circuit in below.c) Find the Av, if the Vs = 100mV_rms, IDSS = 12mA, VP = -4V, VDD = +12V, RD =3.6kΩ, RS = 1.1kΩ.d) Find the Vo, if a load resistance of 10kΩ is connected to the output of the circuit.Vs = 50mV_peak, IDSS = 12mA, VP = -4V, VDD = +12V, RD = 3.6kΩ, RS = 1.1kΩ.
A 60Hz sourcewith an effective voltage of 240 volts supplies 4500 volt-amp to a load with a p.f. of 0.75 lagging. Determine the parallel capacitance required to improve the power factor to: a) 0.9 lagging and b) 0.9 leading. What per cent reduction in line current resulted in part (a)?