Answered: DETERMINE THE VERTICAL DISPLACEMENT OF…

DETERMINE THE VERTICAL DISPLACEMENT OF JOINT C OF THE TRUSS. EACH MEMBER HAS A CROSS-SECTIONAL AREA OF A = 300mm?. E = 200 GPa. G F 3 m A В C D E 4m 4 m 4 m - 4 m 3 kN 3 kN 4 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: THE FORCE SYSTEM SHOWN HAS A RESULTANT SE HORIZONTAL COMPONENT OF 4,074.098 IS ACTING ON THE RIGHT…

A: Horizontal component…

Q: CB kN AB kN 2.5m 2.5m 3. Determine the forces in the truss shown in B D 2.5m Figure by using method…

Q: 3. Determine the displacement at C. Assume A is a fixed support, B is a pin, and D is a roller. El…

Q: B. The bent beam ABC is attached to pin at C and rests against a roller support at B. Neglecting the…

Q: 10.Determine the vertical displacement of joint C of the truss. Each member has a cross-sectional…

A: Given data: A=300 mm2. E=200 GPa.

Q: 5 Determine the vertical displacement of Joint C.Assume the members are pin connected at their end…

A: The length of the span AB(LAB)=4 m, The length of the span BC(LBC)=4 m, The length of the span…

Q: Compute the force in BD in kN. P1 = 51 kN, P2 = 53 kN and x = 5.3 m. write numerical value only and…

A: P1=51kN P1=53kN To find force in member BD

Q: Given beam (P = 24 kN) a) Find the internal forces at the midpoint of the BC length by cutting…

Q: Use Virtual Work Method to solve the horizontal displacement of joint D in mm of the truss system…

Q: Determine the vertical reaction at support C of the given beam, El is constant. (in kN) (FIG. 6) 250…

A: Answer We can determine the vertical reaction at C using the deflection at midspan due to a point…

Q: Generate the stiffness matrix for the frame corresponding to three degrees of freedom 1, 2, 3…

Q: 3. Determine the vertical displacement of joint B. AE is constant. Use the principle of virtual…

A: Principle of Virtual work: It states that the virtual work done by the external active forces on an…

Q: Determine the horizontal displacement and rotation at D. The frame members have a 10cm x 1Ocm square…

Q: Consider bending contributions only and take that the flexural stiffness as EI. Problem 1: Find the…

Q: Q. I For the truss shown in Q. $. determine the horizontal and vertical components of the…

A: Given:- The truss is given with two forces acting on it The magnitude of the vertical force at B =…

Q: 4. Solve for the support reactions of the beam shown below using SDM. Assume beam is prismatic and…

Q: Determine the magnitude of the vertical displacement of joint C of the truss (in units of mm). Each…

Q: Determine the internal moments at each joint using Slope-deflection equation method. El is constant.…

Q: Determine the design angle θ (0° ≤ θ ≤ 90°) forstrut AB so that the 400-lb horizontal force has a…

A: Given: The angle between member AB and AC is 40o. The force in the member AC is 500 lb. Consider the…

Q: Determine the vertical displacement of joint C of the truss. Each member has a cross-sectional area…

Q: For the beam in the figure; a) Find the coordinates of the geometric center and the moments of…

A: Draw the free body diagram. Equilibrium of horizontal forces, ∑Fx=0Ax=0

Q: C 3m А B 4m

Q: find the bar forces is P1 is 141 kN, P2 is 159.5 kN and P3 is 178 kN

Q: Q5. Determine the horizontal displacement of point C of the frame shown below. Take E=200 GPa and 1=…

A: Given :

Q: 2. Determine the vertical displacement at point C (i.e., Acv) for the following rigid frame, assume…

A: The solution of the above problem is provided in the below images:

Q: Q2- For the frameshown in the figure determine the total displacement of join A if support C…

Q: Determine the horizontal displacement of joint C. Assume the members are pin connected at their end…

A: Member force and virtual member force diagram given below- Applying unit load in C direction-

Q: #2 Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(10°) mm“.…

A: The force of shear is a sensitive force on the surface. It's said to be the bending moment the…

Q: Q. 4. Using the force method of analysis, determine the force in member BD. AE is constant. 2 kN Q.…

Q: Calculate the horizontal displacement of point B. El is constant for all members C D A

A: Deflection from Unit Load Method =∑n∫1nMm dsEIM=Member Bending Moment Due to Given Load. m=Member…

Q: 8 ft A B - 8 ft - 8 ft

A: The virtual work method is mainly related to a force that is acting on a particle or member of the…

Q: Use Virtual Work Method to solve the horizontal displacement of joint D in mm of the truss system…

Q: Determine the vertical displacement of joint A of the truss. Each member has a cross-sectional area…

A: Solution Given Data Cross-sectional area A=300 mm2 E=200 GPa

Q: Use Virtual Work Method to solve the horizontal displacement of joint D in mm of the truss system…

Q: Determine the horizontal displacement of joint A. AE is constant. Use the principle of virtual work.…

A: Solution Considering the Diagram: Analyzing the truss with external load P in horizontal direction…

Q: Determine the horizontal and vertical displacement of joint C for the loaded truss shown.

A: Angle of member AC with horizontal,Tan(θ1) = 55, θ1 = 45°Angle of member AB with horizontal,Tan(θ2)…

Q: Solve for the force of member BC using method of sections.

A: Consider the figure,

Q: Use Virtual Work Method to solve the horizontal displacement of joint D in mm of the truss system…

Q: Determine the horizontal component of the force applied by the smooth circular guide on the mass A.…

A: Hi

Q: Determine the displacement at C and the slope at for the beam in Fig Q9. El is constant. Use the…

A: for given question we have to first calculate bending moment diagram of question which requires…

Q: 2.64 The rigid beam of negligible weight is supported by a pin at O and two ver- tical rods. Find…

Q: Determine the vertical displacement at joint C of the truss. Each member has a cross-sectional area…

Q: 1. Solve the slope at each support and the deflection at the midspan (pt. C), in terms of the…

Q: Problem 2 Determine the position of the resultant from support A when it intersects the bottom chord…

Q: 1. Determine the vertical displacement of joint D. Use the method of virtual work. AE is constant.…

Concept explainers

Plane and Space Trusses

In civil engineering, a truss is the most important structure that forms the most fundamental member of any building structure and commercial complexes. Trusses are composed of individual members or links that are interconnected by suitable joints, such as rivets, welds, or bolts, and nuts. In trusses, the interconnection leads to the formation of a series of triangles joined together such that all the triangular members behave as a single rigid body. In a simple truss, three members are connected to form a truss member. In trusses, the force always acts at the joints or the interconnection between the individual members.

Question

DETERMINE THE VERTICAL DISPLACEMENT OF JOINT C OF THE TRUSS. EACH
MEMBER HAS A CROSS-SECTIONAL AREA OF A = 300mm?. E = 200 GPa.
G
F
3 m
A
В
C
D
E 4m
4 m
4 m
- 4 m
3 kN
3 kN
4 kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(a) Compute the vertical displacement of the hinge at C in Figure P8.34. EI is constant for all members, E = 200 GPa, I = 1800 × 106 mm4 . (b) The designer would like to offset the vertical displacement of the hinge at C by moving the support A. How far should support A be moved horizontally?
For the truss in Figure P8.3, compute the horizon-tal and vertical components of the displacement of jointC. The area of all bars = 2500 mm2, and E = 200 GPa.
Determine the value of the force P that must beapplied to joint C of the truss in Figure P8.7 if the verticaldeflection at C is to be zero. The area of all bars = 1.8 in.2and E = 30,000 kips/in.2
In Figure P8.27 support D is constructed 1.5 in. tothe right of its specified location. Using Bernoulli’s prin-ciple in Section 8.8, compute (a) the horizontal and verti-cal components of the displacement of joint B and (b) thechange in slope of member BC.
For the steel rigid frame in Figure P8.31, com- pute the rotation of joint B and the horizontal displace- ment of support C. Given: E = 200 GPa, A = 500 mm2 , I = 200 × 106 mm4
Compute vertical displacement of E if: 100 kips acts dowmward at A A unit force acts down at E
Determine the vertical displacement of joint C of the steel truss shown in Fig (a). The cross-sectional area of each member = 300mm² and E = 200GPA.
a) Under the applied loads support B settles 0.5 in. Determine all reactions. b) Compute the deﬂection of point C. Given: E = 30,000 kips/in.^2 and I = 240 in.^4
A truss is loaded with nodal force at C as shown TOS-003. If the truss members have identical rectangular section of 5 cm x 8 cm, with E = 70 GPa, compute the vertical displacement at joint C .
Use Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. A=2.8 B=24.0 C=28 Determine the following: Vertical Reaction at B in kN. Moment Reaction at A in kN-m.
Assume that EI = 4.0 x 10^4 kN-m^2 is constant for the beam.
Determine the vertical displacement of joint C of the steel truss shown inFig.a. The cross-sectional area of each member is A = 400 mm2, and Est = 200 GPa.