A Tainter gate used to control water flow from the Uniontown Dam on the Ohio River is shown; the gate width is w = 34 m. Please show complete solution. Determine the VERTICAL of the hydrostatic force (in kN) acting on thegate. Indicate the direction by putting an U for upward and D fordownward after your numerical answer *Determine the magnitude (in kN) of the TOTAL HYDROSTATIC FORCEacting on the gate. *What angle (in degrees) does the hydrostatic force F make withhorizontal? * A Tainter gate used to control water flow from the Uniontown Dam on the OhioRiver is shown; the gate width is w = 34 m.R = 20 m%3DD = 10 mWaterDetermine the magnitude and direction of the HORIZONTALCOMPONENT of the hydrostatic force (in kN) acting on the gate. Indicatethe direction by putting an R for right and L for left after your numericalanswer. *

The problem is of finding hydrostatic forces on submerged surfaces. (a) The magnitude of forces. The…

Answered: Determine the VERTICAL of the…

Determine the VERTICAL of the hydrostatic force (in kN) acting on the gate. Indicate the direction by putting an U for upward and D for lownward after your numerical answer *

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 15t k-8-36V Unit of the Correct Answer: ft Decimal Places required in the final answer: 3

Q: 180 kN 270 kN B 3 m 21 E = constant = 200 GPa I = 420x10 mm 3 m 3 m The beam has an additional load ...

Q: Name three ways that a project manager can build good teamwork in a project team.

A: three ways that a project manager can build good teamwork in a project team:

Q: Calculate: a) depth of compression block, "a" b) fs

Q: etermine the maximum deflection for the beam

Q: You have seen bottle and container caps in use all around you. Investigate the design of bottle caps...

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the ques...

Q: Write the shear force and bending moment equations at each segment of the beam shown. Draw the V (Sh...

Q: What are the values needed to compute for the amount of coal required in kilos for a power plant? pl...

A: The major function of the power plant is to convert coal energy into electricity. As a result, the f...

Q: 4. The main reason for cracks in masonry joints is: A. O Moisture B. O Sulphate С. Magnesium D. O So...

A: Answer:- B Explaination:- Sulphate content of bricks to be used in the masonry should be needed a c...

Q: With the exception of urban roads, the more generous a road's design dimensiðns are, the safer the r...

A: (1) True The more generous will be the design dimension, ghe safer will be the road.

Q: A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replace...

Q: A drect-drive crawler tractor with a rated blade capacity of 12 LCY is being used to exchange the lo...

A: soil moving from loose common earth to hard clay and also the data to find out production is provide...

Q: 13. A3 m wide rectangular channel conveys 12 m/s of water at a depth of 2 m. Calculate: (1) Specific...

A: Given, Width of channel (b) = 3m Normal depth = y= 2m Discharge (Q)=12 m³ /sec q= Q/b= 12/3 = 4m²/s...

Q: Situation 1] A circular road is proposed to be laid out with tangent AB whose bearing is N87054'E in...

A: Step 1: Tangent length T = Radius x tan D/2 R = 1720 / 4.5 =382.22 m T = 382.22 x tan(4.5/2) = 15m ...

Q: With the exception of urban roads, the more generous a road's design dimensions are, the safer the r...

A: True

Q: 7. In fig. fluid A is water, fluid B is oil(s= 0.85). Determine the pressure difference between poin...

Q: LINE TRIALS NO. OF DANGKAL MEAN DANGKAL FACTOR (m/ ) АВ 1 9.25 ВА 2 8.75 АВ 8.75 ВА 4 9.00 3.

A: Prob 4 Step 1: No. of stations -4 Line – AB, BA, AB, BA

Q: study of Mechanics of Deformable Bodies to Civil Engineers?

A: Mechanics of Deformable Bodies:

Q: Find the resultant F of the concurrent 8F m force system shown in figure which consists of 3P 10 5P ...

A: The given values are as follows T=300lbP=200lbF=500lbTo Find The concurrent force system,

Q: ssive

A: We have to calculate maximum tensile and compressive stresses so we should know about its moment of ...

Q: The testing of concrete for compression will require the preparation of 12 standard concrete cylinde...

Q: 1A 50 m tape weighs 2.5 kg. Ever y time measure ment is performed, the tape is supported points at i...

Q: Find Find 300 EN 30 F1= 205KN

Q: Superelevation is developed over a given length of roadway, beginning with a road to being fully sup...

A: This question is related to the Highway Engineering and Traffic Engineering.

Q: An S-curve hydrograph has been obtained for catchments of 270 km2 from a 3 hour unit hydrograph. The...

Q: The testing of concrete for compression will require the preparation of 12 standard concrete cylinde...

Q: what letter are those?

A: According to me This symbol represent bending moment at any distance ( x ) in a beam.

Q: PROBLEM 06: The cable in fig. has a diameter of 1/5in and the pin in the pulley has a diameter of 3/...

Q: Compute the internal force of member CD & EF

Q: Design a built up sal wood column fabricated out of 50 mm thick planks of 250 mm 300 mm width to car...

Q: A. A liquid is compressed in a cylinder has a volume of 1000cu.cm at 2.0MPa and a volume of 990cu.cm...

A: Given data, Initial volume of liquid = 1000 cm³ Initial pressure = 2 MPa Final volume = 990 cm³ Fin...

Q: 6. A piece of 3 m long and having a 30 cm by 30 cm is placed in a body of water in a vertical positi...

Q: pls provide clear solns, thanks

A: Given data, H1 (mercury)= 675 mm Hm1 (water) = 225 mm Hm2 (water) = 300 mm Specific gravity of merc...

Q: e bending moment diagram for the continuous beam ABCD

A: The given beam is a continuous beam with given loading. To find the moments at each points of the be...

Q: Q5: A: Give the definition to four of the following : 1- Surveying 2- Ranging 3- В.М 4- Leveling 5- ...

Q: 10. In a building, to provide ultimate comfort to occupants can be used. А. О АС В. О HVAC C. O Vent...

A: Given : building To determine :for provide ulti...

Q: Listen Factors that contribute to collisions can be broken down into the following

A: Level of Service At the point when a street is conveying a traffic volume equivalent to its ability...

Q: 9. Desiccants are chemicals that:

A: Dessicants are used to protect metals from rusting, in moisture prone areas, helps to fight condensa...

Q: The velocity with which an elementary surge wave can travel upstream in a channel with depth y = 1.6...

Q: Eight men can excavate 15 cubic meters of drainage open canal in 7 hours. Three men can backfill 10 ...

Q: . At a point, the major principal stress 66 KPa (c) and the minor principal stress is 34 KPa (T). a)...

Q: 180k/m A

A: Lets assume reaction at A is Ra and reaction at B is Rb. Given that: Rb= 0.30 Ra. ........(...

Q: Determine if the structure is statically determinate. Solve the moment and the x and y components (e...

Q: What is the actual ground area covered by a 20 cm x 20 cm size vertical aerial photograph, at an ave...

Q: (O 5 day BOD of wastewater and Gil ultimate BOD. Assume K = 0.12/day. %3D

A: BOD 5 IS TO BE CALCULATED

Q: 14. A fire detector cannot detect: A. O Radiation А. В. O Heat С. O Light D. O Smoke

A: Fire detector cannot detect

Q: 1. Draw the bending moment diagram for the continuous beam ABCD loaded as shown. The relative moment...

Q: A triangular direct runoff hydrograph due to a storm has a time base of 60 hr and a peak flow of 30 ...

Q: A 9-m simply supported beam is subjected to a uniformly increasing load of zero, 3m from the left su...

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for y...

Q: An unconfined coastal aquifer has a seaward specific discharge of 2.0 (cu.m/day)/m. The aquifer is u...

A: Data given Hydraulic conductivity, k = 23 m/day Specific discharge from costal aquifer, Q'ox = 2 (m3...

Concept explainers

Electric Circuit and Components

An electrical circuit or electrical network is a pre-determined pathway to make the electrons flow in the desired direction. The flow of electrons will set up a current flow in the circuit. Normally, the flow of electrical current is opposite to the flow of electrons. An electron is a fundamental sub-atomic particle of an atom possessing a negative charge. To initiate the flow of current and achieve the desired output, the electrical circuit should necessarily be composed of closed pathways. The pathways are made-up of good conductors of electricity such as aluminium and copper.

Question

A Tainter gate used to control water flow from the Uniontown Dam on the Ohio River is shown; the gate width is w = 34 m.

Please show complete solution.

Determine the VERTICAL of the hydrostatic force (in kN) acting on the
gate. Indicate the direction by putting an U for upward and D for
downward after your numerical answer *
Determine the magnitude (in kN) of the TOTAL HYDROSTATIC FORCE
acting on the gate. *
What angle (in degrees) does the hydrostatic force F make with
horizontal? *

A Tainter gate used to control water flow from the Uniontown Dam on the Ohio
River is shown; the gate width is w = 34 m.
R = 20 m
%3D
D = 10 m
Water
Determine the magnitude and direction of the HORIZONTAL
COMPONENT of the hydrostatic force (in kN) acting on the gate. Indicate
the direction by putting an R for right and L for left after your numerical
answer. *

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 every part of asked question has been explained briefly in below solution

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 21 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The pipe shown is subjected to the force of F = 80 lb. Determinethe angle θ between F and the pipe segment BA and the projection ofF along this segment.
note: a = 3.7 m b = 31.0 kN/m c = 35 kN
Compute the force acting on a 5 m diameter gate which is inclined60° from the vertical if the height of sea water above the bottomof the gate is 6 m. (Gs = 1.03). a. 955.36 kN b. 877.35 kNc. 853.15 kN d. 942.39 kN
a = 3.7 m b = 31 kN-m c = 35 kN
The crest gate shown consists of a cylindrical surface which AB is the base, supported by a structural frame hinged at C. it is retaining water on one side. The length of the gate perpendicular to the paper is 8.79 m. use R = 14 m. and 0 = 49 degrees. Determine the angle (in degrees, acute) of inclination of the total hydrostatic force acting on surface AB.
Find the required force per unit width of the dam that the latch must supply to keep the gate closed if h is equal to 5 meters. Note: water y=9.81kn/m^3
Determine the rate of flow in the channel of Prob. 14.84, knowing that b= 12 ft, d1 = 4 ft, and d2 = 5 ft.Reference to Problem 14.84:The depth of water flowing in a rectangular channel of width b at a speed v1 and a depth d1 increases to a depth d2 at a hydraulic jump. Express the rate of flow Q in terms of b, d1, and d2.
A rectangular gate 1.60 m wide and 2.40m high has water on one side and is inclined 45\deg with them horizontal. Water is 1.50m above the top of the gate. Evaluate the location, in meters, of the center of pressure from the top of the gate. a. 1.34 b. 1.49 C.1.56 d. 1.64
The wall separates water and glycerin (ρ=1260 kg/m^3). Consider a unit width of the rectangular panel AB when d = 6 ft. Where is the line of action of F2 relative to point B in feet? What is the net hydrostatic force F acting on the gate? Indicate the direction by putting R for right and L for left after a space from your numerical answer.
The sluice gate is a circular arc of radius 5m and angle B=60°. The depth of water behind the gate is 4m. Knowing that the length of the gate is 3m (dimension perpendicular to the paper), determine the vertical component of the hydrostatic force acting on the gate.
A triangular plate of 1 m base and 1.5 m altitude is immersed in water. The plane of the plate is inclined at 30° with water surface while the base is parallel to and at a depth of 2 m from the water surface. Calculate the position of the center of pressure in meters. a.2.987 b.1.896 c.3.234 d.2.264
A round viewing point window of diameter D= 0.9 m is situated in a large tank of sea water with sg= 1.03. The top of the window is h= 1.5 m below the water surface, and the window is angled at 60 degrees with respect to the horizontal. (1) Why is the hydrostatic force acting on the window? (2) Locate the corresponding center of pressure measured vertically from the water surface.