Answered: Determine the view factors from the…

Engineering

Mechanical Engineering

Determine the view factors from the base of a cube to each of the other five surfaces.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.27P: Determine the rate of radiant heat emission in watts per square meter from a blackbody at (a) 15C,...

See similar textbooks

Related questions

Q: Calculate the view factor FBA for the following shape. The radii for the hollow circle, circle A…

A: Given :- Circle A radii : Outer Radius (R) = 8 m Inner Radius (r) = 5 m Circle B radius : Radius…

Q: 2. Calculate the view factor FBA for the following shape. The radii for the hollow circle, circle A…

A: Given that, Radius of hollow circle A, rA=8 m, and RA=10 m,Radius of circle B, RB=5 m,Vertical…

Q: 1. A circular furnace has 2 end black surfaces and surface 1 is kept at 500 K and surface 2 is kept…

Q: Two large parallel surfaces (surface 1 and surface 2) kept at constant surface temperature of T= 300…

Q: Determine the view factors F32 and F23 between the rectangular surfaces shown in the figure.

A: X=1 mZ1=0.2 mZ2=0.2 mY=0.4 m

Q: Consider a cylindrical enclosure whose height is twice the diameter of its base. Determine the view…

A: Let us consider a cylinder whose height is twice the diameter of its base as shown below –

Q: Consider an enclosure consisting of 12 surfaces. How many view factors does this geometry involve?…

A: Given Data N-Number of surfaceN=12Ist dtermining the number of view factors by Directly Methodafter…

Q: A spherical particle of diameter Di = 10 mm is suspended by a thin wire within a cylindrical tube of…

Q: What properties are required to determine the view factors between two surfaces Emissivity of…

A: What properties are required to determine the view factors between two surfaces Emissivity of…

Q: Consider a 20-cm-diameter spherical ball at 800 K suspended in air. Assuming the ball closely…

A: Given data as per question Diameter of sphere = 20 cm Sphere temperature = 800 k wavelength = 3um

Q: A spherical particle of diameter D1 = 10 mm is suspended by a thin wire within a cylindrical tube of…

Q: Determine the view factors from the base of the pyramid shown in Figure 12-14 to each of its four…

Q: QUESTION 6: Two parallel disks of diameter D = 0.8 m separated by L = 0.4 m are located directly on…

A: Given Data,D=0.8mL=0.4mT1=T2=450K (black body)T3=300K (black body) i.e us the backside…

Q: 1.5) Fill in the blanks: A body whose surface properties are independent of wavelength is said to be…

Q: Determine the view factor between two gray surfaces A and B. Their emissivities are εA = 0.90 and εB…

A: Dear student, we are suppose to solve only 3 sub parts. Please post other parts as a separate…

Q: Calculate the view factor FBA for the following shape. The radius for the hollow circle, circle A…

A: Given :- Radii of hollow circle A : Outer radius (R) = 8 m Inner radius (r) = 5 m Radius of circle…

Q: the outer surface temperature of the furnace should be kept below 45°C. Based on the above…

Q: A small disc-shaped earth satellite, 1m in diameter, circles the earth (radius 6250 km) at a…

A: Given details: d=1 mε1=ε2=0.3Tsatellite=-18°CT2=27 °Cσ=5.67×10-8 w/m2k4 here σ=stefan boltzman…

Q: Based upon the reradiating properties of absorptivity, reflectivity and transmissivity, how would…

A: For any body absorptivity is defined by factor α, reflectivity is defines by ρ and transmissivity by…

Q: Two plane disks each 125 cm in diameter are parallel and directly opposite each other. They are…

A: given; diameter of disc (d)=125cm=1.25mseperate distance (l)=50cm=0.5mtemperature of disc A…

Q: A flat, circular silicon wafer is uniformly heated by a flat, circular surface located above it. The…

A: Given Data, Let hemispherical surface is treated as surface 1, surrounding as surface 2 and the…

Q: Two coaxial parallel disks of equal diameter 1 m are originally placed at a distance of 1.5 m apart.…

Q: Consider a cylindrical enclosure with A1, A2, and A3 representing the internal base, top, and side…

A: Given: The diagram of the cylindrical enclosure with having area of surfaces 1, 2, and 3 is given…

Q: Consider two infinitely long thin concentric tubes of circular cross section as shown in figure. If…

Q: Two adjacent rectangles are perpendicular to each other., The first rectangle is 1.52 x 2.44 m and…

Q: Consider a room with dimensions as in the sketch. Assuming all emissivities of surfaces are equal to…

A: Please refer next page for the answer.

Q: 3.Determine the total number of view factors that need to be evaluated directly for a 4-surface…

A: Given data: n=4 Need to determine the total number of view factors that need to evaluated directly.

Q: Determine the view factors from the very long grooves to the surroundings without using any view…

A: The schematic view of the geometry

Q: 19. A right circular cylinder has a height of 1 m and diameter of 75 cm. Find the view factor for…

Q: Consider an enclosure consisting of five surfaces. How many view factors does this geometry involve?…

A: Understand that the geometry has five surfaces. Write the formula for number of view factors for a…

Q: Calculate the net heat flux per unit area and by radiation between two infinitely large parallel…

A: Introduction: Radiation heat transmission occurs in the form of electromagnetic waves, primarily in…

Q: (a) Two surfaces, A and B has a temperature of 4500 K and different spectral emissivity as shown in…

A: Given: The temperature, T = 4500 K The Stefan Stefan Boltzmann’s constant, σ = 5.67x10^-8 W/m^2.K

Q: A right circular cylinder has a height of 1 m and diameter of 75 cm. Find the view factor for the…

Q: Consider the sun, which is considered to be a blackbody with a surface temperature of roughly 5800…

A: Given : The surface temperature of sun= 5800 K Assumption : Sun is a black body.

Q: A gray body with a constant surface temperature of 7000C and a surface area of 500cm2 radiates in a…

Q: Consider two very large parallel plates with diffuse, gray surfaces.

Q: Consider a 20-cm-diameter spherical ball at 800 K suspended in air as shown in Fig. 12-12. Assuming…

Q: Consider a hemispherical furnace with a flat circular base of a diameter D. Determine the view…

Q: Calculate the view factor FBA for the following shape. The radii for the hollow circle, circle A and…

A: The shape factor of hollow circle A w.r.t circle B can be calculated by Subtracting the shape factor…

Q: A large number of long tubes, each of diameter D,are placed parallel to each other and at a…

A: (a) The view factor from the plate to the tubes can be determined as,

Q: For a surface, how is irradiation defined? For diffusely incident radiation, how is irradiation on a…

Q: Determine the view factors from the very ducts and long grooves shown in the Figure to the…

A: Hello. Since your question has multiple sub-parts, we will solve first three sub-parts for you. If…

Concept explainers

Radiation

Radiation can be described as the energy in the form of a particular matter or electromagnetic waves traveling in the air and can be in the form of light, sound, and heat. Radiation can be detected through special instruments like X-rays. The radiation from a cooler object is less intense as compared to the radiation from hot objects.

Question

Determine the view factors from the base of a cube
to each of the other five surfaces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two large parallel plates with surface conditions approximating those of a blackbody are maintained at 816C and 260C, respectively. Determine the rate of heat transfer by radiation between the plates in W/m2 and the radiative heat transfer coefficient in W/m2K.
11.31 A large slab of steel 0.1 m thick contains a 0.1 -m-di- ameter circular hole whose axis is normal to the surface. Considering the sides of the hole to be black, specify the rate of radiative heat loss from the hole. The plate is at 811 K, and the surroundings are at 300 K.
1.28 The sun has a radius of and approximates a blackbody with a surface temperature of about 5800 K. Calculate the total rate of radiation from the sun and the emitted radiation flux per square meter of surface area.
Determine the total average hemispherical emissivity and the emissive power of a surface that has a spectral hemispherical emissivity of 0.8 at wavelengths less than 1.5m, 0.6 at wavelengths from 1.5to2.5m, and 0.4 at wavelengths longer than 2.5m. The surface temperature is 1111 K.
11.41 Determine the steady-state temperatures of two radiation shields placed in the evacuated space between two infinite planes at temperatures of 555 K and 278 K. The emissivity of all surfaces is 0.8.
11.68 Two infinitely large, black, plane surfaces are 0.3 m apart, and the space between them is filled by an isothermal gas mixture at 811 K and atmospheric pressure. The gas mixture consists of by volume. If one of the surfaces is maintained at 278 K and the other at 1390 K, calculate (a) the effective emissivity of the gas at its temperature, (b) the effective absorptivity of the gas to radiation from the 1390 K surface, (c) the effective absorptivity of the gas to radiation from the 278 K surface, and (d) the net rate of heat transfer to the gas per square meter of surface area.
Determine the rate of radiant heat emission in watts per square meter from a blackbody at (a) 15C, (b) 600C, and (c) 5700C.
How can you determine the view factor F12 whenthe view factor F21 and the surface areas are available?
A circular cone of diameter D with a length L ispositioned on a common axis with a circular disk, also ofdiameter D, at a distance L. A cylindrical surfaceof diameter D with a length L and a circular disk, ofthe same diameter D, are oriented coaxially at a distance L Determine the view factors F12 for the two geometries. Which of the two geometries has the higher view factor value?