Determine y(t) for 3 < t < 4 given the following: x(t) = u(t) — u(t − 1) + r(t − 2) – r(t − 3) − u(t – 3)h(t) = r(t + 1) − 2r(t) + r(t − 1)a. _y(t) = √₁²₁(1 – t – t)(t + 2)dtO b. y(t) = √³₁ (1 + r − 1)(x − 2)dty(t) = f₁²3(1 – t)(2 — t + t)drO d. y(t) =(1 + t)(−2 − t + t)dt

Answered: Image /qna-images/answer/e9cfc4bd-24cd-499b-87bd-6df092898082.jpg

Determine y(t) for 3 < t < 4 given the following: x(t) = u(t) − u(t − 1) + r(t − 2) − r(t − 3) − u(t − 3) h(t) = r(t + 1) − 2r(t) + r(t − 1) ○ a. y(t) = √₂/²₁(1 − t − t)(t + 2)dt b._y(t) = √₁²₁(1 + t − t)(t − 2)dt - c. _y(t) = √₁²3(1 – t)(2 − t + t)dt d._y(t) = √₁²3(1 + r)(−2 − t + t)dt

Determine y(t) for 3 < t < 4 given the following: x(t) = u(t) − u(t − 1) + r(t − 2) − r(t − 3) − u(t − 3) h(t) = r(t + 1) − 2r(t) + r(t − 1) ○ a. y(t) = √₂/²₁(1 − t − t)(t + 2)dt b._y(t) = √₁²₁(1 + t − t)(t − 2)dt - c. _y(t) = √₁²3(1 – t)(2 − t + t)dt d._y(t) = √₁²3(1 + r)(−2 − t + t)dt

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.16P

See similar textbooks

Similar questions

If G(s) = 1 / (s + 2), find the response c(t) if the input r(t) = u(t), a unit step, assuming zero initial condition.
the following statements given, write if each statement is true or false. a. If the complex frequency domain function, F(s), is derived using a “One-sided” Laplace Transform, the inverse of that function, f(t), is only valid for t ≥ 0. b. When using an ideal transformer, if voltage increases from primary side to secondary side, current also increases from primary side to the secondary side. c. Initial value theorem states that the initial value of a time function f(t) can be obtained from its Laplace Transform F(s) by multiplying the transform by s and letting s approach zero. ..
When the unit step function is applied to the input of the system whose block diagram is given below, the output response takes the value c (0.2) = 0.11 for t = 0.2 s and c (infinity) = 0.333 for t = infinity. What is the steady-state error of the system? calculate.
The response of a system, h(t) is given as in Figure 1 below where the amplitudeof this signal is 7. Then,this system is excited by an input of x(t) = (u(t) × (u(-t)+u(t))) /1. 1)Illustrate the input signal, x(t). 2)Calculate the convolution output of the system y(t) = x(t) ∗ h(t). Nextdetermine y(t) when t is 1 sec 2)Prove the solution in Q2 is comparable when solving in frequency domain(Laplace). Next, sketch the signal for convolution output.
1. a) Show that if y(t)=h(t)*x(t), then Y(s)=H(x)X(s). 2. b) Use the result given in (a) to find f(t) if F(s)=as(s+a)2.
Signal and system The mathematical model of a system is y" (t) + ay'(t) + by(t) = a (t) + ca (t) where a=1, b=2 and c=1. 1) Find zeros and poles of the system. 2) Show them onto the S-Plane (the complex plane) 3) Discuss the BIBO stability of the system.
2) In the circuit shown in Fig. 1, the capacitor is initially charged to V0 volts and the switch isclosed at t = 0. Obtain the current, i(t), for t> 0 using the Laplace transform.
I need help with the question below Consider a causal LTI continuous system described by the differential equation y′′(t) + 3y′(t) + 2y(t) = x(t) where y(t) is the system output and x(t) is the input.1. Find the transfer function H(s) of the system.2. Find its poles and zeros. From its poles and zeros, determine if the system is BIBO stable or not.3. If x(t) = u(t) and initial conditions are zero, determine the steady-state response yss(t)4. If the initial conditions were not zero, would you get the same steady state?. Explain
When the unit step function is applied to the system input given the block diagram below, the output response takes the value c (0.2) = 0.11 fort = 0.2 s and c (infinity) = 0.333 for t = infinity. What is the steady-state error of the system? calculate
Let x(t) be defined as?(?)={3, −1≤?≤0, {1, 0<?≤1, {0, ????. Sketch the following:
a) Y(ω) = 1/(5+jω) The expression above defines the frequency domain signal Y(ω) from a time domain signal y(t) i) Determine the imaginary & real parts of Y(ω). ii.Determine the signal y(t) that produced the signal Y(ω). b)What are the 3 areas of application of i.Signals ii.Systems c) Briefly summarise with explanation the difference between discrete & continuous time signal and also write an expression that describes each signal type.
a. Find the circuit’s input, or driving-point, impedance, Zi, in the s-domain.