Develop a mathematical model of the performance of a plastic bonding process given the process data shown in the table below for the situation where the time indicated is related to the time that the plastic sample is clamped after the binder is applied. Time Binding strength achieved 0.000 0.000 0.250 -0.043 0.500 0.542 0.750 0.934 1.000 0.997 1.250 0.958 1.500 0.954 1.750 0.980 2.000 0.997 2.250 1.000 2.500 0.998 Make sure that your model is a typical input-output type model and that you give the full explanation for the result. Describe any approximations, assumptions, and modeling decisions you make. Your model should be in the form of: ?(?) = ?(?, ??????????) ??? ? ≥ 0

Develop a mathematical model of the performance of a plastic bonding process given the process data shown in the table below for the situation where the time indicated is related to the time that the plastic sample is clamped after the binder is applied. Time Binding strength achieved 0.000 0.000 0.250 -0.043 0.500 0.542 0.750 0.934 1.000 0.997 1.250 0.958 1.500 0.954 1.750 0.980 2.000 0.997 2.250 1.000 2.500 0.998 Make sure that your model is a typical input-output type model and that you give the full explanation for the result. Describe any approximations, assumptions, and modeling decisions you make. Your model should be in the form of: ?(?) = ?(?, ??????????) ??? ? ≥ 0

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.5P: To determine the thermal conductivity of a structural material, a large 15-cm-thick slab of the...

See similar textbooks

Similar questions

A sample of crosslinked polvisoprene rubber undergoes a constant strain rate axial tension experiment The initial sample measurements are 3.60 cm gauge length (axial direction); 0.b2 cm wide; 0.1/ cm thick:
. An elliptical hair, 10.0 cm long, has the following semi-diameters A = 35\mu , B=25 \mu When the hair was extended from 10.0 cm to 10.1 cm at 50% RH the force on the hair increased by 11.3 grams. What is the modulus of elasticity in GPa, (round off) Group of answer choices 10.0 1.0 8.0 4.0
A long steel rod is placed horizontally between two supports, one at each end. The rod bends a little in the center. Which property of this rod can be used to estimate how much the rod should bend at the center? 1. Its Shear Modulus 2. Its Young's Modulus 3. All of these Moduli can be used to compute how much it bends. 4. Its Bulk Modulus.
At 250C, the interfacial tension between water and n – octyl alcohol is 8.50 dyne/cm. if the surface tension of n-octyl is 27.53 dyne/cm and that of the water is 72.75 dyne/cm, predict whether water spreads on the alcohol by calculating a) Work of cohesion of n-octyl b) Work of adhesion and c) the spreading coefficient of water on the alcohol. Will alcohol spread on water?
The nuchal ligament in a horse supports the weight of the horse’s head. This ligament is much more elastic than a typical ligament, stretching from 15% to 45% longer than its resting length as a horse’s head moves up and down while it runs. This stretch of the ligament stores energy, making locomotion more efficient. Measurements on a segment of ligament show a linear stress-versusstrain relationship until the stress approaches 0.80. Smoothed data for the stretch are shown. The volume of the ligament stays the same as it stretches, so the cross-section area decreases as the length increases. Given this, how would a force F versus change in length ΔL curve appear?
The materials laboratory that you direct received the following data on the tensile strength in MPa of 15 samples of Aluminum Nitride. The data obtained for each sample are: Sample Endurance (Mpa) SAMPLE (STRENGTH) MPa 1 190 2 233 3 268 4 160 5 257 6 300 7 310 8 262 9 185 10 205 11 275 12 245 13 220 14 290 15 228 You are asked to calculate the Weibull modulus, m, considering that the probability of failure is n/16, where n is the number of specimens that failed at a given stress. You can use Excel to speed up the calculations.
A band of polyisoprene is to hold together a bundle of steel rods for up to 1 year (52 weeks). If the stress on the band is less than 10MPa at that stage, the band will not hold the rods tightly any longer. Determine the initial stress that must be applied to the polyisoprene band when it is slipped over the steel. A series of tests showed that an initial stress of 7MPa decreased to 6.8MPa after 6 weeks. In a simple model, the rate at which stress relaxation occurs in elastomers is related to the relaxation time λ, which is considered a property of the elastomer. The stress after time t, is given by σ = σoexp(-t/λ) where σo = original stress A. None of the mentioned B. σ = 11.73 MPa C. σ = 10.29 MPa D. σ = 13.03 MPa
The following table lists molecular weight data for a polypropylene material. Compute the number-average molecular weight, Molecular Weight Range (g/mol)//// xi////// wi 8,000–16,000//// 0.05/// 0.02 16,000–24,000 ///0.16// 0.10 24,000–32,000 ///0.24// 0.20 32,000–40,000 ///0.28// 0.30 40,000–48,000 ///0.20// 0.27 48,000–56,000 ///0.07// 0.11 Round your answer to 0 decimal places.
To determine the thermal conductivity of a structural material, a large 15-cm-thick slab of the material is subjected to a uniform heat flux of 2500 W/m2 while thermocouples embedded in the wall at 2.5 cm. intervals are read over a period of time. After the system had reached equilibrium, an operator recorded the thermocouple readings shown below for two different environmental conditions: Distance from the Surface (cm) Temperature (C) Test 1 0 40 5 65 10 97 15 132 Test 2 0 95 5 130 10 168 15 208 From these data, determine an approximate expression for the thermal conductivity as a function of temperature between 40 and 208C.
R Value: Wall: 0.961m2k/w Floor: 0.676m2k/w Roof: 0.7465m2k/w In a table format show with calculations and research how much money you can save by installing a 115mm layer of insulation (R2.9) in your walls, floor and ceiling over a 5 and 10 year period. Consider the capital costs. Hint: State the current R value of each component. Convert to U value. Calculate new R value of each component (walls, floor and ceiling). Convert to U value. Use Q(W)=A*(change in U)*temperature change. Determine price for installation of new insulation. Determine price saved based on less heat loss through each component separately, then add all values together, and calculate per 5 years and per 10 years. Present all of this information in a table. You do not need to draw any diagrams, simply add the R value in series with your current components R values. Assume the energy cost is 25 cents kWh
The shear modulus, G, of an alloy can be determined by measuring the angular twist, θ,resulting from a torque applied to a cylindrical rod made from the alloy. For a rod of radius Rand a torque applied at a length L from a fixed end, the modulus is found by G=2LT/pR4θ.Examine the effect of the relative uncertainty of each measured variable on the shearmodulus. If during test planning all of the uncertainties are estimated to be 1%, what is theuncertainty in G?
4) If two variables are highly correlated, does this imply that changes in one cause changes in the other? If not, give at least one example from the real world-that illustrates what else could cause a high correlation.