Discuss about the basic features of CNC machines and FMS systems. Draw a diagram if necessary

Q: Determine the expected Fanning friction factor for water at 28 degrees Celsius, flowing through a…

A: Give data as per the question The internal diameter of the tube =15 mm = 0.015 m velocity =0.3 m/s…

Q: A fluid flows at 455 m3 per min inside a rectangular duct, whose cross-section has a length of 150…

A: Given data: Q=455 m3/min=7.5833 m3/secL=150 mw=85 cm Need to determine the average velocity of the…

Q: 5. Calculate the net hydrostatic force per unit width on the rectangular panel AB and its location…

A: Answer: ◆The net hydrostatic force per unit width on the rectangular panel AB is 28.88304 kN. ◆ It's…

Q: 10. A reverted epicyclic gear train for a hoist block is shown in Fig. 13.39. The arm E is keyed to…

A:

Q: Air at 3.4 atm abs and 15°C is flowing in a steel pipe whose ID is 75-mm. The flow rate is kept at…

A:

Q: A room contains air at specified conditions, 20°C and 85 kPa, and relative humidity of 85%. The air…

A: Given: Let us consider the given data, Relative humidity,ϕ=85% T=20°Cρ=85 kPa To find: Partial…

Q: 2/186 The hoisting system shown is used to easily raise kayaks for overhead storage. Determine…

A:

Q: Air at 110°F passes through a -in-diameter orifice having a flow capacity constant of 3.5. If the…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: AB = 1923.27 N AC = 264.57 N BC = -738.27 N

Q: The 600 lb pole is anchored by cables to supports at A, B and C.The coordinate directional angles of…

A:

Q: A body reaches the ground in 3 s when it is released with zero velocity from the top of a building.…

A: Given, Time taken by body to reach ground = t = 3 s Initial velocity of the body = u = 0 m/s   Let…

Q: 3. In a reverted gear train, as shown in Fig. 13.32, two shafts A and B are in the same straight…

A:

Q: The spring-held follower AB has a weight of 0.75 lb and moves back and forth as its end rolls on the…

A:

Q: A ____ cycle consists of two Rankine vapor power cycles that use different working fluids.

A: Given A ____ cycle consists of two Rankine vapor power cycles that use different working fluids.

Q: The flow velocity of air over a flat plate of dimension 1160 ×610 ×25 mm at 30 OC is 3.2 m/s. The…

A: Given Plate dimension = 1160 mm X 610 mm X 25 mm Temperature = 30o C Velocity = 3.2 m/s Top surface…

Q: Instantaneous Center Method—Analytical For the reciprocating saw shown in FigureP6.21, use the…

A: Introduction: Intantaneous center method: An instantaneous center method is a graphical approach for…

Q: Which of the ff. will likely reduce the power requirement in pumping the same fluid at the same vol…

A: GIVEN DATA-  A MCQ IS GIVEN ABOUT PUMPING POWER  WE HAVE TO SELECT CORRECT ANSWER

Q: A shaft is to have a semicircular grove machined around the circumference at a specified location.…

A:

Q: Determine the missing properties, show it on a P-V diagram. T (°C) u (kJ/kg) P (kPa) 400 v (m²/kg)…

A:

Q: What is the discharge of the pipe into reservoir B if a 1.2 m diameter concrete pipe 1800 m long…

A:

Q: A: When the pressure of liquid is increased from 3.5 MN/m² to 6.5 MN/m² its volume is found to…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked.…

Q: Water @ 4C flows through a 100-mm ID smooth pipe. The Reynolds # of the flow is 150000. Determine…

A: following is the solution-

Q: HW2: A hydroelectric power plant built for a design head of Hn=12.5 m should develop a rated output…

A: Given: Head of the plant→Hn=12.5 m Rated power→P=12000 hp=8952 KW Because efficiency→e=0.90 Density…

Q: Determine the horizontal and vertical components of reaction on the beam caused by the pin at 8 and…

A: To determine the reaction for the given loading.

Q: A venturi meter (ID = 15 cm) is set in a pipe whose ID is 50 cm. Water flows through the venturi…

A: GIVEN DATA-  A VENTURIMETER GIVEN WITH DIAMETER 15cm AND 50cm PRESSURE DROP 400Pa  WE HAVE TO FIND…

Q: Steam at 20 MPa and 620°C enters a steam turbine and expands to a condenser pressure of 100 kPa. An…

A:

Q: Example procedure of Level, Flow, Pressure and Temperature control system in mechanical engineering

A: Given: Briefly explain level, flow, pressure, and temperature control system example procedure.

Q: (b) A horizontal electronic component, 5 mm wide and 10 mm long with a surface temperature of 35°C…

A: Note: As per policy, we can solve the first question from multiple questions. Please resubmit the…

Q: n on ased Oves orce tiff- num osi- 3/134 The spring attached to the 10-kg mass is nonlin- ear,…

A:

Q: Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in…

A:

Q: Arrow tool, Arc tool, Pen tool and Drawing Elements tool are used to add ...... to ChemDraw…

A: Solution is attached below:

Q: 2. The 250-kg, 4-m-wide rectangular gate shown in the figure is hinged at B. The gate is to be…

A:

Q: the work output from the turbine

A: Given data;  At steady state,  Steam enters a turbine having mass,m1=500 kg/s  Specific…

Q: 1. Column ABC shown has a uniform rectangular cross section and is braced in the x plane at its…

A: The factor of safety,FOS=2.7 Load,P=5.4×103N Length,L=600mm Modulus of Elasticity,E=70GPa=70×109Pa

Q: etermine the viscosity of liquid biphenyl at 450K in cP

A: Given Temperature = 450 K To find Viscosity

Q: 35 and wet bulb temp at 25c Dry bulb temp what is the humidity percantage?

A:

Q: A bow uses a 16-gram arrow as its ammo, and its string behaves as an ideal spring. When the string…

A:

Q: An unsteady, incompressible, velocity field is given by the following vector: V = (u, v, w) = (t +…

A: Given: Let us consider the given velocity field in vector, V→=u,v,w=t+5x-7yi→+-3yj→+2t-4zk→ To find:…

Q: Plasma spraying is a process used to coat the surface of a material with a protective layer to…

A:

Q: The particle has a mass of 0.45 kg and is confined to move along the smooth horizontal slot due to…

A: Introduction: The idea of equilibrium or balance is a fundamental concept when dealing with forces.…

Q: Determine the force in each member of the loaded truss. Make use of symmetry of the truss and of the…

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN ALL MEMBER

Q: Learning Goal: Consider the mass and pulley system shown. Mass m₁ = 32 kg and mass m₂ = 10 kg. The…

A:

Q: cross sectional dimensions at a-a Figure 1 shows the steel bar has its original dimension. if it is…

A: Given: The load, P = 50 kN The elastic modulus of steel, Est = 203 GPa The poison ratio of steel,…

Q: 8. An epicyclic gear train, as shown in Fig. 13.37, has a sun wheel S of 30 teeth and two planet…

A:

Q: A pitot tube with dia of 3cm is installed in a pipe with ID150 mm. Water flows through the pipe, and…

A:

Q: compound shaft consists of segment (1), which has a diameter of 1.7 in., and segment (2), which has…

A:

Q: A fan is used to transport CO2 gas (MW = 44 g/mol) gas at rest @ 700mmHg. At the discharge end, the…

A:

Q: In the resistance welding process, select the factor/s that contribute to accomplish coalescence:…

A: Resistance welding: It is the permeant joining process for metals by passing current for a length of…

Q: Water is flowing at a rate of 25 gpm in a pipe and at one end of the pipe, the internal diameter is…

A:

Q: various loading. Draw the shear and moment diagram. Fb 12 MPa. and Fv = 1.00 MPa a. Design the beam…

A:

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.