Draw the figure to an enlarged scale in Isohyetal method

Q: 5-6. PROBLEMS, (cont.) 5-8. Calculate the bearing and distance of course E-F. Ans.: 5-9. a. b. C. d.…

A:

Q: Compute the roots of the auxiliary equation (m² - 4) (m² - 1) - 0.

A: Lets solve the quadratic equation,(m2 - 4)(m2 -1)=0Firstly expand and simplify the…

Q: 4.1 A cube of moist soil weighs 330 lb and has a volume of 3.00 ft3. Its moisture content is 27.0%…

A:

Q: a. If the mass of bullet is 5g and the mass of the gun is 10kg and the velocity of the bullet is…

A:

Q: Case Study: A 0 Design of a foundation (Reinforced Concrete) 4m Feu = 30 MPa fx = 460 N/mm² Ⓡ H 5m…

A:

Q: answer is given just give the solution and right answer.

A: The objective of the question is to determine the flow in line AD, the flow in line DC, and the…

Q: In the following structure, bolt B has a diameter of 1.75” and bolt A has a diameter of 2.50”. Bar…

A:

Q: Using the building section associated with the floor plan in figure below, assume a total dead load…

A:

Q: 1-102 Determine the intensity w of the maximum distrib- uted load that can be supported by the…

A:

Q: 4 Deep ZE 5' 2" Deep 21" Plan View of Building Volume of Backfill Section A-A 48 Deep 11 3' 6" Deep…

A:

Q: A community of 300 residents (water use per person = 130 gpd) is looking at using two sources for…

A: Optimal System Configuration****Calculations:**The Total Cost function is . Differentiate with…

Q: HW 1: Determine the deflection at point D of the beam shown in Fig. below by the virtual work…

A:

Q: For the cantilever retaining wall shown below. Calculate the factor of safety with respect to…

A:

Q: Which joint would be the best place to start your analysis of the truss shown?

A:

Q: A student is concerned with the amount of air pollution students are exposed to in the school’s…

A: The objective of the given scenario is to enhance the reliability of an investigation assessing…

Q: B P a с b

A:

Q: of longitunal rebars. 1. area 2-area of transverse bars. 3. area of termal rebars. 4. area of edge…

A: Given :- Strength of rebars () =              Strength of concrete () =             Length of the…

Q: Find the risk of liquefaction for each soil layer (at the mid-point of layers) Determine the…

A: Risk of Liquefaction:Sand: The risk of liquefaction for the sand layer is low as the groundwater…

Q: Calculate thr A) ultimate column loads  B) upward ultimate soil pressure C) footing effective depth…

A: Given:- Axial loads at a distance of 4m           Allowable soil pressure  =           Size of…

Q: 5.1.3 Determine the uniform flow depth in a rectangular channel 2.5 ;m wide with a discharge of 3…

A: Given Width 2.5 mDischarge 3 m3/ secSlope 0.004Roughness 0.015To find out Uniform depth

Q: F3-12. Determine the force in members GF, CF, and CD and state whether they are in tension or…

A:

Q: bearing at A. Determine the resultant internal loadings acting on the cross section. at C.

A: Given:- Total span of shaft = 3m             UDL acting = 800N/m             Point load acting =…

Q: What is bearing?

A: The term 'bearing' in civil engineering refers to the direction or angle at which one point or…

Q: The inside diameter of an open cylinder tank was measured. The results of four replicate…

A:

Q: Text - Problem 2.56] (Show your answer in ppmv as well as ppbv.) 56 Convert the concentration of SO₂…

A:

Q: ) find the reactions at supports A and B for the beam shown in Figure 3.

A:

Q: Problem 7. [Concepts: Allowable stresses and factor of safety] Two aluminum rods AB and AC support a…

A:

Q: Q4. In Figure 3, If the coordinate direction angles for F3 are a3 = 120°, 3 = 45° and 3 = 60°,…

A:

Q: 1 11. Determine the resultant internal loadings on the cross section at point C Assume the support…

A: Determine the internal resultant force at point C.

Q: A 60-cm-wide belt moves as shown in the figure. Calculate the horsepower requirement assuming a…

A:

Q: An estimated 60 percent of the annual precipitation in a watershed (drainage area = 20,000 acres) is…

A: Given data:

Q: 2 m 2 m 3 m Figure P2.11 A Dry sand; e = 0.5 G, = 2.65 B Water table Sand Gs = 2.65 e = 0.6 C Clay w…

A:

Q: ) Replace the parallel force system acting on the plate by a resultant force and specify its…

A:

Q: Referring to the same river as the previous question, how many minutes does it take before the…

A:

Q: Show that 1. gamma sat= (e/w)(1+w/1+e) gamma water. 2. Gamma dry= Gamma/1+m

A:

Q: 1. A motorist travelling at 104 KPH on an expressway intends to leave the expressway using an exit…

A:

Q: illustrate normal stresses in cross section.

A: Normal stress is the stress component perpendicular to a given surface, such as a cross section of a…

Q: A test driver’s perception-reaction time is being conducted on a special testing track with wet…

A: (1) Initial velocity of the car(2) Final velocity of the car(3) Visible distance(4) Coefficient of…

Q: 4) Draw the shear and moment curves and sketch the deflected shape. E P = 36 kips 2' 31 F P= 24 kips…

A: Beam is givenpin supporetd at A and roller supported at DFINDSFD , BMD and deflceted shape of the…

Q: 5.1.2 A 2-m-wide rectangular channel with a bed slope of 0.005 has a depth of flow of 1.5 m.…

A:

Q: In the following structure, determine the stress in each bar. Indicate whether the stress is tensile…

A:

Q: a 9 ● с B col 0.2 m m d FO F₁ F₂ A structure is contructed of three beams DABC, GDEF and HEB.…

A: Sign conventions and assumptions required to solve this strucutureDraw the free body diagram of the…

Q: Two rectangular tanks, A and B, are filled to a height, ha and hb respectively, as shown; ha is…

A:

Q: Am acquifer is recharged by precipitation that infiltrates through fertilised fields. The…

A:

Q: 9.19 Compute the force required to punch a 1-in.-diameter hole through a -in.-thick boiler plate.…

A: diameter hole through a boiler plate that is ½ inch thick. The material has a maximum shear strength…

Q: 7 kN-m 2m BO 3 m 0.90 KN C 2.4 KN 0.90 KN 2m D 3 m 1.3 kN EO 1m F

A: Moment at A Concentrated load

Q: Determine the discharge of the weir having a head of 0.6 m in L/s if a 51⁰ triangular weir is used.…

A: Determine the discharge of the weir having a head of 0.6 m in L/s if a 51⁰ triangular weir is used.…

Q: Plot a histogram for concrete strength and discuss the characteristics. The number of bins can be…

A: From the given data set of concrete strength.

Q: Based on the given design criteria, and without carrying out any preliminary calculations, develop a…

A: The objective of the given problem is to develop detailed conceptual designs for three types of…

Q: Problem #1 Determine the magnitude and the location of the hydrostatic force on the 2 m by 4 m…

A: