Draw the shear and moment diagram. Show the complete and legible answers/solutions. Add 9 in all the loads. Example: 40 + 9 = 49KN, 68 + 9 = 77KN/m 40 KN 68 KN/m B C A L = 1.5 m. L= 2.2 m. L = 3.6 m. RB RD

Q: A reinforced concrete beam has a width of 380 mm, effective depth of 570 mm and carries a uniform…

A: The given values are as follows,Width=380mmDepth=570mmLive load =90kN/mDead load…

Q: 1. A cantilever beam of length L with stepwise constant cross section carries a vertical load P at…

A:

Q: Disks A and B each weigh 2 Ib and have initial velocities as shown in the figure. The coefficient of…

A:

Q: The two lines shown are the EGL and HGL of a pipeline. Which statement is true? A B C There is no…

A: Option (2) is the correct answer.

Q: 4. (Problem 6.42 from the text book) Knowing that a given vertical shear V causes a maximum shearing…

A: Shear stress Shear stress is a force that tends to produce material deformation by sliding along a…

Q: 69 KN/m 41 KN B C D А L= 1.5 m L= 2.2 m L= 3.6 m RD RB

A:

Q: A prestressed beam has a width of 300 mm and depth of 600 mm. It is subjected to a bonded prestress…

A:

Q: An initially empty tank on Earth is being filled with water so that the height of the water in the…

A:

Q: Draw shear and moment diagram of the beam.

A:

Q: A metallic cube 30 cm side and weighing 450 N is lowered into a tank containing a two fluid laye of…

A: This question is related to the Fluid Mechanics.

Q: A stream has a width of 25 m and depth of flow 2.5 m. The mean velocity of the flow is 1.10 m/s.…

A:

Q: Problem 2. For the truss loaded as shown, determine the forces in members CD, C. and IJ. Also…

A: Given Data -

Q: Engineering Mechanics - Topic: Centroids Determine centroid Y-bar with respect to X-axis,

A:

Q: Q1/The cost of a vehicle at the time of purchasing is (80,000)$, its expected useful life is (10)…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: The figure shows a system for delivering lawn fertilizer in liquid form. The nozzle on the end of…

A:

Q: What is the Maximum moment in kN-m. Given: w1 = 47, w2 = 18, a = 3, b = 3, and c = 3. %3D w1 kN/m w2…

A:

Q: I. PROBLEM SOLVING: PROBLEM COLVNING: USING CENTER HINE METHOD AGURE 1: 0125m 10.40m 10.40m lom…

A:

Q: /115 Calculate the x- and y-components of all forces act- ing on each member of the loaded frame. D…

A:

Q: 50 kN 40 kN/m 10 kN/m OB

A:

Q: The dry weight of a sample is 330 g, and its weight when saturated with water is 360 g. The apparent…

A: We have to determine the porosity of the sample and assuming the sample is coated with a material of…

Q: What is the Maximum moment in kN-m. Given: w = 45, a = 3, b = 3, %3D and c = 3. w kN/m A Stomst B…

A: Finding RA AND RD Using equilibrium equations, we get Summation of upward forces=summation of…

Q: Element A is subjected to the stress state shown in the x-y plane (+x is to the right, ty is up).…

A:

Q: • Consider a flow of two miscible streams of fluid ( deionized water and a solution of 10 nm…

A: Solution-The deionized water and solution =10mm particlesD=1×10-14m2/s in waterIn the main channel…

Q: The system in the figure shows fours applied forces and a 50 kN-m couple, answer the following…

A: Find The line of action of the resultant force is at a perpendicular distance.m from point A

Q: Design for a tension member based on the following conditions below: • Tension member: single…

A: Answer Based on the given loading we need to find required gross section area of tension member.…

Q: Compute the natural frequency in side sway for the frame is figure below. If the initial…

A:

Q: Please Help me to solve the follo wing phy si cal example #1 A boiler has 0.22 m2 of net furnace…

A:

Q: Who uses record drawings for planning future projects? O Contractor O Owner O Facility Manager O…

A: Option 3 is correct  Facility manager

Q: Draw the missing view. exact scaling not needed

A: Since you have posted multiple subparts We will solve only the first four.... Kindly repost the…

Q: Prepare a set of level notes for the data listed. Perform a check and adjust the mis- closure.…

A: Given data,

Q: 1 A six-meter high stand-alone column, with fixed support at the bottom and pinned support at the…

A: ASTM A992 steel rolled into W21x57 section is used to create a six-meter high stand-alone column…

Q: HW:B Find the mux Value of P) that can be aPPlied on the Cantilever beam Shown in figure r knowing…

A:

Q: 120 kN 60 kN 120 kN 120 kN 3 m 3 m 6 m - 3 m B 2 m 4 m Figure P-427

A:

Q: In a rectangular channel, two reaches M and N are in series, with reach M being upstream of reach N.…

A:

Q: In the figure, a 50 mm pipeline leads downhill from a reservoir and discharges into air. If the loss…

A:

Q: 2. Calculate: supports reactions 30 kN 20 kN -10 kN/m A B |C |D - 2 m - 2 m .4 m NOTE: No hinge is…

A:

Q: 31. Water flows in a vertical channel. Use the given data to find the frictional pressure drop from…

A: The given values are as follows ,H=6ftDh=0.145ftP=1000Paisa Xe=8%Vi=3ft/sTi=522fTo Determine the…

Q: A screw Jack has a square thread of 75 mm mean diameter and a pitch of 15 mm.

A: Given data: d=75 mm=0.075 mp=15 mm= 0.015 mμ=0.05lever (L)=500 mm = 0.5 mLoad to be lowered (W)=25…

Q: MA = 12 kN. m w = 3 kN/m А В 6 m

A:

Q: Two 3/16" E70 fillet welds of 15 in. Iong are subjected to a load P. Using LRFD, compute the…

A: Answer (a) Minimum weld length requirement Minimum weld length may not be less than 4 times the…

Q: 50 kN 40 kN/m 10 kN/m AA OB 20KN-m 1m + 1m 2 m+ -2 m 4 m

A:

Q: 6 ft> C. 3 kips A 6 ft 2 kips 15 ft 6 ft 20 ft- For the three hinged arch shown determine the…

A:

Q: The wall thickness of a 4-ft diameter spherical tank is 5/16- in. Calculate the allowable internal…

A:

Q: flowchart detailing the deisgn of One-way Slab

A: One-way Slab: - It is a slab in which longer span is equal or greater than 2 times of shorter span…

Q: (3) The beam is subjected to an internal moment of M = 50 kN.m as shown. Determine the percentage of…

A: parallel axis theorem : The parallel axis theorem, also known as the Huygens–Steiner theorem or…

Q: frepame Plinth Area of all building an approx. estimale of building with tolal so00 sqm, uslng as…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: 8. The BODS of a waste sample was found to be 160 mg/L. The initial oxygen concentration of the…

A:

Q: 50 kN 40 kN/m 10 kN/m B.) OB 20kN-m 1m 1m 2 m- 2 m+ 4 m

A:

Q: 1. What is the surface texture in microinches is specified for the cylinder surface with a maximum…

A: 1) The surface texture in micro inches is specified for the cylinder surface with a maximum material…

Q: The two lines shown are the EGL and HGL of a pipeline. Which statement is not true?

A:

Frames

The trusses and frames are the two most important structural members of civil engineering. Trusses are the interconnection of links and other structural members. The interconnection with other members makes the system behave as a single member that supports and transfers loads. Trusses are generally two types, plane truss, and space truss. Frames on the other hand form the skeleton of any building construction. Frames are structures formed by the connection of beams, columns, slabs, and joists. These members provide the building with the required structural support.