1Draw the shear and moment diagrams for the loaded beam. After you have the diagrams, answer the questions in order to gainconfidence in your plots.5 KN5 kN7 kN mm7 kNm 5 mQuestions:When x 1,5 m,kN M-V-kN-mWhen x- 8.0m,V=kN M-kN-mWhen x- 13.0 m, V-kN M-kN-mWhen x- 20.0 m, V-kN M-kN-mThe maximum (absolute value) shear force in the beam is:|Vmal167kNhe maximum (absolute value) bending moment in the beam is:IMnalkN-m

Answered: Image /qna-images/answer/9737bf12-93ff-4b03-a774-7d33bb339381.jpg

Draw the shear and moment diagrams for the loaded beam. After you have the diagrams, answer the questions in order to gain confidence in your plots S kN 5 KN 7 kN m -5 m 4 m 7 kN Questions: When x- 1,5 m. V- kN M- kN-m When x-8.0m, V- kN M- kN-m When x 13.0 m, V- kN M- kN-m When x- 20.0 m. v- kN M- kN-m The maximum (absolute value) shear force in the beam is: Vmal 167 kN The maximum (absolute value) bending moment in the beam is: Mnal kN-m 圣る

Draw the shear and moment diagrams for the loaded beam. After you have the diagrams, answer the questions in order to gain confidence in your plots S kN 5 KN 7 kN m -5 m 4 m 7 kN Questions: When x- 1,5 m. V- kN M- kN-m When x-8.0m, V- kN M- kN-m When x 13.0 m, V- kN M- kN-m When x- 20.0 m. v- kN M- kN-m The maximum (absolute value) shear force in the beam is: Vmal 167 kN The maximum (absolute value) bending moment in the beam is: Mnal kN-m 圣る

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the bending moment 2.25 m to the right of point A for the beam shown below if P = 1705 N, T = 3205 Nm, a = 0.95 m, b = 0.97 m, and c = 1.15 m. Round of the final answer (in N m) to four decimal places
Use the graphical method to construct the bending-moment diagram and identify the magnitude of the largest moment (consider both positive and negative). The ground reactions are provided.MB = 146 kN-mMC = 53 kN-mAy = 16.58 kN (down)Dy = 16.58 kN (up)
The 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel?
From the beam shown. Let P = 30 kN, Q = 2 kN/m, L =6m and EI = 200MNm^2Determine the following;C. Slope at L/3. D. Deflection at L/3.
Draw the shear and moment diagrams given that Ra=110.2 kN, Rb=310.1 kN, Rc=220.6 kN, Ma=-124.5 kN m, Mb =-258.9 kN m, Mc = -160.5 kN
Draw the shear and moment of the beam shown by Shear and Moment Equation Method and by Relation of Load to Shear and Moment Method. P=74 6P= 6(74) = 444 kN 8P = 8(74) = 692 kN
What is the general moment equation? Section the beam at the rightmost segment of the beam. El = 75,000 kN∙m2
may i know why did you use the 35 kN twice and not the 70kN? also, why is the moment at A = 0?
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x 150 mm section and E = 80 GPa. Note that: a = 3.7 m b = 31.0 kN/m c = 35 kN Find the ff. A. Vertical reaction at B in kN. B. Moment reaction at A in kN-m. C. Deflection at point C in mm. D. Deflection at midspan of AB in mm.
Determine the magnitude of F so that the resultant couple moment acting on the beam is 1.5 kN.m clockwise ?
A continuous beam is loaded as shown 18. Which of the following gives the fixed end moment AB in kN-m? a. 12 kN-m b. 8 kN-m c. 10 kN-m d. 5 kN-m 2. Which of the following gives the distribution factor at B for the member BA in %? a. 33.3% b. 66.6% c. 35.47% d. 45% 3. Which of the following nearly gives the moment at B using moment distribution method in kN.m? a. 12.89 b. 13.2 c. 11.2 d. 14.6
20 -In the cantilever beam in the figure, bar clearance L= 225 cm and single load acting on the free end of the bar P = 12 kN. The cross-sectional effects at point B will be calculated. Accordingly, the Moon on the fixed support at point A=? A) None.B) 27000C) 12000D) 0E) 9000