None QI:a- Identify the zero-force members in the30truss.b- Determine the force in each member of thetruss. State if the members are in tension orcompression.3 mGroup A: Take P= 900 kNGroup B: Take P = 700 kNEvening Group: Take P 600 kN3 m3 m 3 mQ2:Determine the internal normal force, shear force,and moment at point B.w N/mGroup A: Take w = 300 N/mGroup B: Take w 600 N/mEvening group: Take w = 450 N/mA2 m2 mQ3:Draw the shear force and bending momentdiagrams for the beam.30 kNMkN mGroup A: Take M = 30 kN.mGroup B: Take M 60 kN.mEvening group: Take M 15 kN.m1.5 m 1.5 m 1.5 m 1.5 m

Hi! Thank you for the question As per the honor code, We’ll answer one question since the exact one…

Answered: Draw the shear force and bending moment…

Engineering

Civil Engineering

Draw the shear force and bending moment diagrams for the beam.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

15. If Q = 1261.26 N, calculate the force in member BE in kN. Indicate whether the member is in compression (-) or tension (+).
In the shown loaded truss, P = 225 kN, calculate the following and select the correct values from the given drop-down list: a) the support reactions at roller A and pin B (i.e., Ax, Ay & By ). 3 m b) the angle a. c) the forces in members AC and AB using the method of joints (i.e., FAC & FAB).
1. Find the resultant of tension F and Ta. 27.6 kNb. 37.2 kNc. 33.7 kNd. 44.6 kN2. What is the angle that their resultant makes with the horizontal rod OA? a. 28 degb. 37 degc. 33 degd. 44 deg3. Find the weight, W to prevent uplift. Use a factor of safety of 2.5. a. 49.23 kNb. 42.86 kNc. 59.51 kNd. 44.72 kN
Compute the force in member BD in kN. P1=117 kN, P2=72 kN and x = 7.8 m. Write numerical value only and in 2 decimal places
If the allowable bearing stress for the material under the supports at A and B (σ_(b allow)= 1.5 MPa, determine the size of square bearing plates A’ and B’ required to support the load. Dimension the plates to the nearest mm. The reaction at the supports are vertical. Take P = 100 kN.
Set P1 = 49 kN , P2 = 32 kN . Determine the force in member AD, and state if the member is in tension or compression. Determine the force in member BC, and state if the member is in tension or compression. Determine the force in member BD, and state if the member is in tension or compression.
Thecable of length 15m supports the forces W1 = W2 = W at B and C. (a) Derive the simultaneous equations for β1, β2, and β3. (b) Show that the solution to these equations is β1 = 41.0◦, β2 = 9.8◦, and β3 = 50.5◦. (c) Compute the force in each segment in terms of W.
Determine the magnitude of the 15 points force in member CD using method of section * (O 35.3KN Tension O none of the above (O 15.02KN Tension () 27.7 KN Compression (O 13.83 KN Tension O 16.2 KN Compression
A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
Using method of sections, determine the reaction at A, the force in members BD, FE and CE if θ=30degrees, Φ=60degrees and d=12ft.
Determine the tension at AC. A. 55.23 kN B. 52.53 kN C. 32.55 kN D. 25.35 kN
Take 2 KN/m in place of 1.5. Determine support reaction