drawing all the views

Q: Draw the edge view

A: Solution:   The edge view of the given plane is drawn below:

Q: draw the front, side and top view of the figure thankss

A: Dimensions are assumed

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: orthographic view (software drawn)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: draw multiview drawing including auxiliary view

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: draw multiview drawing

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: -rce. What is the best angle?

A: To find angle.

Q: can you make a sketch of the solution

A:

Q: I need answers to this part for a review activity.

A: Contour definition is used to describe the profiles of complicated shapes, whereas tube bending is a…

Q: Choose the correct option

A: The correct option is II graph shown correct

Q: り ート Joz

A: GIVEN DATA- F1=79N F2=268N F3=274N θ1=23' θ2=62' X=2 Y=9 WE HAVE TO FIND RESULTANT

Q: Given the Top View, Right View, and the outline of the Front View. Create a section view based on…

A:

Q: 97SD Make freehand sketches of any four (in all) common tools, utensils or pieces of furniture . 1.

A: Table is a furniture. Thus, sketch table:

Q: shadow price

A: Given;  Determine  the shadow price of the source? Where,  In a linear programming problem, if a…

Q: Required the three views in first angle projection

A:

Q: Analysis and conclusion from the given picture.

A: Answer given below:

Q: about the y a

A:

Q: mechanical drawing Draw the front, left and top view.

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Draw front and top view

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Identify the lines

A: Answers: 1.Phantom line 2.Section line 3.Hidden line 4.Cutting plane line 5.Leader line 6.Hidden…

Q: What type of drawing is shown (the bottom of the object is horizontal, all lines going towards the…

A: LETS define each one of them   ISOMETRIC DRAWING: Isometric drawing is just a 2D representation of a…

Q: Draw the front, Top , and side planes for a complete cut *Note the shape is symmetrical

A: a. Front b. Side c. Top

Q: Create an oblique drawing

A:

Q: 14 sketch in the missing object and ce nter lines on 14

A: Given figure  To sketch the missing lines  And hidden lines

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: draw missing view?

A: Given data: - The upper part of the given figure is the front view of the component. The lower part…

Q: 15 FRONT 100 20 50

A:

Q: MAKE DETAILED DRAWING AND THREE VIEWS IN FIRST ANGLE PROJECTION use creo parametric to sketch

A:

Q: make a three-view drawing, complete with dimensions, of the part. Show the dimensions with the view…

A: the given isometric view

Q: Determine the shortest distance and the shortest horizontal distance. Complete all views. Y в HRP…

A: At the point when two lines in space are not resemble to one another, yet they also don't converge,…

Q: The front and top views of an object are shown below. Freehand sketch the section view of the front…

A: Given view are top view and front view

Q: Fill in the blank using R-134a

A: Using property table and P-h chart of R-134a, the required properties are taken.

Q: Sketch the othographic  Isometric and  Any other if so draw of the following sketch  ( Use…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Draw by using free hand sketch to find Front, Side and Top views of the following shape

A: Refer the following image for the the free hand sketch  for Front, Side and Top view of the given…

Q: Use creo parametcric 4.0 drawing to Sketch all the compulsary part and partial views, including…

A:

Q: draw the top view

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: How many auxiliary views of the print

A: Auxiliary Views:- When an object has a inclined surface, it is not possible to show inclined surface…

Q: Using the Creo parametric sketch the following: GIVEN - PICTORIAL VIEW DRAW- THE ORTHOGRAPHIC VIEW…

A: given : pictorial view

Q: What is the name of the figure or 3D model

A: Given 3D model To find Figure name

Q: Can you draw on the sketch and show all steps

A: We need to calculate the mass fraction of pro-eutectoid cementite present in various hypereutectoid…

Q:

A: There are three views that can be drawn by using an isometric drawing. TOP View SIDE View FRONT…

Q: 5. According to the given 2 views, try to make the front full sectional view (7') and the left-side…

A: Given:- Top and side view   To find: Sectional A-A view and front view

Q: Draw the view

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: n section views, match patterns should be drawn parallel to one of the edges of the part. True?…

A: In section views, match patterns should be drawn parallel to one of the edges of the part. True?…

Q: Draw front and top view?

A: The Front view and Top view of the given object is drawn by third angle method of projection.

Q: GIVEN - PICTORIAL VIEW DRAW- THE ORTHOGRAPHIC VIEW

A:

Q: Orthographic drawing Needed ( top, front and side view) there are no dimensions

A: Draw the top view (how will it look if seen from the top) for the given figure.

Q: In the following Multiview drawings, find the missing visible and/or hidden lines.

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Know and Understand 1. True or False? The primary purpose of section views is to help feature…

A: As per our guidelines, we can answer only first question. Kindly post the remaining questions in…

Q: 2. Draw the hole in the top and front views: .625 through hole, 90 degree countersink to 1.250 dia.

A: ◆ The purpose of providing countersink is to accommodate the head of the bolt within the workpiece.…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.