Problem 7The drill is jammed in the wall and is subjected to the torque and force shown in .Part APart BA = -215 MPaCorrectPart C((Txy)v) ₁ = 0 MPaAXyCorrecta 20 N-mDetermine the normal stress at point A on the cross section of drill bit at section a-a.Express your answer to three significant figures and include the appropriate units. Enter negative value in the case ofcompression and positive value in the case of tension.ANSWER:125 mmDetermine the transverse stress at point A on the cross section of drill bit at section a-a.Express your answer to three significant figures and include the appropriate units.ANSWER:400 mmSection a-a5 mmDetermine the torsional stress at point A on the cross section of drill bit at section a-a.Express your answer to three significant figures and include the appropriate units.ANSWER:((Txz)T) A =150 N

A drill is subjected to torque, we need to find out the normal stress and transverse stress at point…

e drill is jammed in the wall and is subjected to the torque and force shown in . rt A JA -215 MPa rt B Correct rt C a 20 N-m 125 mm Determine the normal stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: Correct Determine the transverse stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Tay)v) A = 0 MPa 400 mm Section a-a -5 mm Determine the torsional stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Txz)T) A = 150 N

e drill is jammed in the wall and is subjected to the torque and force shown in . rt A JA -215 MPa rt B Correct rt C a 20 N-m 125 mm Determine the normal stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: Correct Determine the transverse stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Tay)v) A = 0 MPa 400 mm Section a-a -5 mm Determine the torsional stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Txz)T) A = 150 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow tube ABCDE constructed of monel-metal is subjected to five torques acting in the directions shown. The tube has an outside diameter d2= 1.0in. The allowable shear stress is 14,950psi and the allowable rate of twist is 2.45degree/ft. Determine the maximum permissible inside diameter d1 of the tube in inches. Use G= 9500ksi.
pls! write the complete solutions. upvote will be given! STRENGTH OF MATERIALS The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. If the valve A is closed and the water pressure is 300 psi, determine the longitudinal and hoop stress developed in the wall of the pipe. Draw the state of stress on a volume element located on the wall and its corresponding Mohr's Circle.
Two solid steel shafts (shafts) in the figureconnected with gears. Permission for steel shaftsthe permissible shear stress is 7000 psi. BC spindle1.6 in diameter and 1.25 in diameter of EF shaftit is known that the width applied to the shaft at the C pointCalculate the large TC torque.
Problem 2): A 20 mm diameter steel rod passes concentrically through a bronze tube (200+Q) mm long, 50 mm external diameter, and 40 mm internal diameter. The ends of the steel rod are threaded and provided with nuts and washers which are adjusted initially so that there is no end play at 25°C. 1. Assuming that there is no change in the thickness of the washers, if the stress produced in the steel is (200+Q) MN/m2 when one of the nuts is tightened, the pitch of the thread being 1 mm: Find the number of turns for the nut and stress in the bronze tube.2. If the temperature of the steel and bronze is then raised to 40°C find the changes that will occur in the stresses in both materials.The coefficient of linear expansion per C is 10 x10-6 for steel and 17 x10-6 for bronze. E for steel = 210 GN/m2 and, E for bronze = 100 GN/m2.Note: Q = 39
The shaft is made of two segments. AC has a diameter of 0.5in, and CB has a diameter of 1in. It is fixed at its ends A and B and is subjected to a torque T=500lb*ft. Gsteel= 10.8*103 ksi What is the minimum shear stress in the shaft?
5.Compute the maximum shearing stress developed in a phosphor bronze spring having a mean diameter of 200 mm and consisting of 24 turns of 20-mm diameter wire when the spring is stretched 100 mm. Assume G = 42 GPa. Use Wahl formula.
Question-02Describe the various types of stresses developed in the shaft AB due to load P acting at the end C as shownin Figure 1.
What is the minimum required bolt diameter (mm) at C ifthe allowable bolt shear stress is 68 Mpa.a. 9 mm c. 11 mmb. 10 mm d. 12 mm Determine the stress (Mpa) in strut BC.a. 5.6 MPa c. 3.2 MPab. 2.8 MPa d. 6.4 MPa Calculate the bolt stress (Mpa) at A if its diameter is 20mm.a. 7.64 MPa c.11.46 MPab. 3.82 MPa d.14.92 MPa
A full forming P= 52 kN axial force acts on the part shaped by the machining method made of xCy steel material. The thickness of the part is t= 20 mm and the steel tensile strength is sigma(tensile) = 620 MPa . Calculate the individual fatigue life of the A and B sections of the machine part for 90% reliability. Draw logarithmic S_N diagrams.
Of the following solid shafts diameter, which is the smallest that can be used for the rotor of a 6 hp motor operating at 4500 rpm, if the maximum shear stress for the shaft is 8500 psi?A. 5/16 inB. 3/8 inC. 1/2 inD. 1 in
Given Y = 9.79 kN/m^3 Find: P @ bottom of tank (kpa) Force (tensile) on each bolt (kN) Stress on each bolt (MPa)
A worker applies the forces P = "-50i" + 40j N and Q = 50i N to the hand- grips of the electric drill. These forces are equivalent to the force R = 40j N acting at the tip of the drill and the couple C = "-1800j" N mm Determine the dimensions a and b.