The rigid beam is supported by a pin at C and an A-36 steel guy wire AB.Part AWIf the wire has a diameter of 0.4 in., determine how much it stretches when a distributed load of 100 lb/ft acts on the beam. The material remains elastic.Express your answer to three significant figures and include appropriate units.Submit10 ftSAB = ValueProvide FeedbackRequest AnswerUnits?

Given: The diameter of wire is, d=0.4 in. The distribution load is, w=100 lb/ft. The length of the…

Answered: e rigid beam is supported by a pin at C…

Engineering

Mechanical Engineering

e rigid beam is supported by a pin at C and an A-36 steel guy wire AB.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.1P: A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar...

See similar textbooks

Related questions

Q: Find the solar heat gain though reference glass with the following conditions 2 m² window area 30°…

A: Solution: Given Data: To Find: (a) The solar heat gain. (b) The overall factor.

Q: Provide a statement of sustainability criteria for a hydrogen car charger at a university campus

A: A sustainable hydrogen car charger at a university campus should meet the following criteria: Use…

Q: A copper pipe carrying hot water is losing heat with a convective heat transfer coefficient of h =…

Q: In order to reduce the steady-state error of a system, a lag compensator was designed as shown.…

A: To find: The steady-state error. Given: The system is shown below.

Q: O A motorist starts from rest at point A on a circular entrance ramp when t = 0, increases the speed…

Q: Determine the reactions at supports for the following Figures. A 40 kN/m 8 m B. -3 m 20 KN 150 kN m

Q: A 8 ft 20 k B G 80 k 8 ft 8 ft 20 k C 20 k X X X F 80 k 8 ft 8 ft 20 K D E ΠΟΙΟΙΟΙ 8 ft 8 ft

Q: Two 270- x 20-mm steel plates are welded to the flanges of a W254 × 89 wide flange beam (see Table…

A: Given: To find: Second moment of area with respect to the horizontal axis through the centroid…

Q: G a-s graph for a rocket moving along a straight track has been experimentally determined. The…

Q: The boom is supported by the winch cable that has an allowable normal stress of allow = 24 ksi. It…

Q: Two steel plates are to be held together by means of 16-mm-diameter high-strength steel bolts…

A: Given: The diameter of high strength steel bolt d=16 mm=0.016 m The maximum average normal stress in…

Q: In servo motors, the position is determined by: a. The frequency of the PWM signal. b. The amplitude…

A: Servo motors control systems

Q: At what angle 8 must the 800-N force be applied in order that the resultant R of the two forces have…

A: “Since you have posted a multiple question, we will provide the solution only to the first question…

Q: A two dimensional diverging duct is being designed to diffuse the high speed air existing a wind…

A: Given: The wind speed at section 1 u1=300 ms The wind speed at section 2 u2=100 ms The air density…

Q: Using the partial motion diagram, answer: a) Complete the motion diagram by adding acceleration…

A: Given: Velocity vector diagram To find: a) Complete the motion diagram by adding acceleration…

Q: A jet airplane moving at 900 km/hr takes 700 N/s of air into is engine, burns 15 N/s of fuel, and…

A: To find: The exhaust gas velocity. Given: The velocity of the jet airplane is v=900 km/hr5/18 m/s1…

Q: A three stage C.P. has impellers (cm) in diameter and (1.8cm) wide at outlet. The vanes are curved…

Q: A container is divided into two equal volumes by a very thin membrane. It is held at a fixed…

Q: Q3/ Saturated steam at 125 kPa is compressed adiabatically in a centrifugal compressor to 700 kPa at…

Q: velocity A ball is shot Vertically into the air @ a of 193.20 81/sec. After 4 secs another ball is…

Q: Which one of the graphs in the image above represents the dependence of the twist-angle on the…

A: According to the question there are many graphs b/w the angle of twist and the length of the rod we…

Q: using excel how can we convert these two 9.81 m/s2 to ft/s2 i. 2000 kg/m3 to lbm/ft3

A: Unit conversion can be done in excel using the CONVERT function. This function is very helpful in…

Q: The bent plate is 1.6 m wide and is pinned at A and rests on a smooth support at B. The fluid is…

Q: he nylon cord has an original length L and is tied to a bolt at A and a roller at B. A force P is…

Q: Which equations would be in the expanded form of the constraint ax ≤ b, where i E (1, 2) and j € {1,…

A: Given equation: aijxi≤biwhere,i ∈ {1,2}j ∈ {1,2} To Find: Expand the equation

Q: 4.43 The rig shown consists of a 1200-lb horizontal member ABC and a vertical member DBE welded…

A: (a) To find: The reaction at E when the cable is anchored at F. Given: At a distance of x=12 ft the…

Q: 5 and 5.66 For the beam and loading shown, design the cross section of the beam, knowing that the…

Q: One kg of CO2 is heated in a 0.5 m3 vessel from -18 C to 93 C. Determine the initial and final…

A: To find: The initial and final state and the amount of energy transfer as heat to the CO2. Given:…

Q: The condensate pump on the Navaho power plant raises the water pressure from 3.5 in of mercury to…

Q: 1)The gravity at a location is 5 m/s². The density of fluid was 2000 kg/m³. The pressure exerted by…

Q: Example: Pressure in A Decelerating Tank of Liquid The tank on a trailer truck is filled completely…

A: Given: The specific gravity of gasoline(γ)=42 lbfft3=6.60kNm3 The deacceleration rate of truck al=10…

Q: 1. The thermal resistance of A, B, C, and D are 1, 2, 2, 4 W/ °C, respectively. The total thermal…

Q: Of the following, the SHORTEST is ______ a. 1.2 miles b. 1610 meters c. 63350 inches d. 1060…

Q: a. What is the maximum bending moment on the beam? Answer in kN-m rounded-off to the nearest…

Q: Kevin's favorite hiking route is on the foothills of Rocky's in Colorado. Kevin's barometer reads…

Q: The load has a mass of 15 kg and is lifted by the pulley system shown. Determine the force F in the…

Q: water sucam? Q2/ An ideal gas initially at 600 K and 10 bar undergoes a four step mechanically…

A: Solution.jpg

Q: A tension test was performed on a steel specimen having an original diameter of 0.503 in. and gauge…

A: Given: The original diameter of steel specimen d=0.503 in The original gauge length l=2 in

Q: The horizontal roof of a building has an emittance of 0.9. Air temperature is 1oC on a clear night.…

A: Conduction and convection heat transfer needed the use of a material medium to transfer heat from…

Q: 5. Determine the maximum possible reduction for cold rolling a 300mm thick slab when u = 0.08, and…

Q: Example 1.3 Apply the conduction equation to the situation illustrated in Figure 1.1, but let k =…

Q: Under what conditions does the Monoclinic system reduce to the orthorhombic system?

Q: Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear…

Q: Two cables are tied together at Cand are loaded as shown. Determine the tension (a) in cable AC, (b)…

A: Given load at C is 400 lb. Tension in cable AC and BC.

Q: Mohr's circle, invented by Christian Otto Mohr, is a graphical representation of the transformation…

Q: Q4: Determine the moment of the force about point 0 of Fig.4. Fig.4

A: According to the question data Force = 600 lb with the help of the figure provided we need to…

Q: Convert the tungsten melting point temperature, 6192 oF into Kelvin units. 3,681 K 11,451 K 3,695…

Q: 15. Fig. 2.48 shows a mercury manometer fitted to a venturimeter in which water is flowing.…

Q: 2-101. Determine the position (x, y, 0) for fixing cable BA so that the resultant force exerted on…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

The rigid beam is supported by a pin at C and an A-36 steel guy wire AB.
Part A
W
If the wire has a diameter of 0.4 in., determine how much it stretches when a distributed load of 100 lb/ft acts on the beam. The material remains elastic.
Express your answer to three significant figures and include appropriate units.
Submit
10 ft
SAB = Value
Provide Feedback
Request Answer
Units
?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 10-ft rigid bar AB is supported with a vertical translational spring at A and a pin at B. The bar is subjected to a linearly varying distributed load with maximum intensity q0. Calculate the vertical deform at ion of the spring if the spring constant is 4 kips/in.
A steel pipe column with pinned ends supports an axial load P = 21 kips. The pipe has outside and inside diameters of 3.5 in. and 2.9 in., respectively. What is the maximum permissible length Lmaxof the column if E = 29,000 ksi and y = 36 ksi?
Solve the preceding problem for an aluminum column with b = 6,0 in., t = 0.5 in., P = 10 kips, and E = 10.6 × 106 ksi. The defied ion at the top is limited to 2.0 in.
An aluminum tube AB with a circular cross section has a sliding support at the base and is pinned at the top to a horizontal beam supporting a load Q = 200 kN (sec figure). Determine the required thickness t of the tube if its outside diameter d is 200 mm and the desired factor of safety with respect to Eu 1er buckling is n = 3.0. (Assume E = 72 GPa.)
A cantilever aluminum column has a square tube cross section with an outer dimension of 150 mm. The column has a length L = 4 m and is designed to support an axial load of 45 kN. Find the minimum required thickness of the section if the factor of safety n = 2.5 with respect to buckling. Assume that the modulus of elasticity is 72 GPa and the proportional limit is 480 MPa.
A W8 × 28 steel wide-flange column with pinned ends carries an axial load P. What is the maximum permissible length of the column if (a) P = 50 kips, and (b) P = 100 kips? (Assume E = 29,000 ksi and y = 36 ksi.)
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.
An aluminum box column with a square cross section is fixed at the base and free at the top (sec figure). The outside dimension b of each side is 100 mm and the thickness t of the wall is 8 mm. The resultant of the compressive loads acting on the top of the column is a force P = 50 kN acting at the outer edge of the column at the midpoint of one side. What is the longest permissible length Lmaxof the column if the deflection at the top is not to exceed 30 mm? (Assume E = 73 GPa
Repeat Problem 11.2-14 using L = 12 ft, ß = 0.25 kips/in., ßRl= 1.5ßL2, and ßR2= 2 ßR1.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?