Each propeller of the twin-screw ship develops a full-speed thrust of F = 375 kN. In maneuvering the ship, one propeller is turning full speed ahead and the other full speed in reverse. What thrust P must each tug exert on the ship to counteract the effect of the ship's propellers? Assume a = 50 m, b= 108 m, c= 15 m. Answer: P= i kN

Each propeller of the twin-screw ship develops a full-speed thrust of F = 375 kN. In maneuvering the ship, one propeller is turning full speed ahead and the other full speed in reverse. What thrust P must each tug exert on the ship to counteract the effect of the ship's propellers? Assume a = 50 m, b= 108 m, c= 15 m. Answer: P= i kN

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.11P: Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.

See similar textbooks

Similar questions

A torque T = 0.30 N-m is applied to a bevel gear B. Bevel gear D meshes with gear B and drives pump A. Gear B has a radius of gyration of 150 mm and a weight of 50 N, whereas gear D and the im- peller of pump A have a combined radius of gy- ration of 50 mm and a weight of 100 N. Find how many revolutions of gear B are needed to get the pump up to 200 rpm from rest. What is the power output of the pump at this speed if it is 90% efficient.
Each propeller of the twin-screw ship develops a full-speed thrust of F = 395 kN. In maneuvering the ship, one propeller is turning full speed ahead and the other full speed in reverse. What thrust P must each tug exert on the ship to counteract the effect of the ship's propellers?
If the speed of the shaft, as shown in Figure 1 below, is 220 rev/min, calculate the magnitudes and orientations of the bearing reactions at A and B for the two-mass system. Given a = b = 250 mm, c = 50 mm, R1 = 60 mm, R2 = 40 mm, m1 = 2 kg, and m2 = 1.5 kg.
Why does the single thrust bearing have two couple moments? is it not supported by the tension cable at CB?
Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.
Find the effect of gyroscopic couple acting on the body of the aeroplane for the following conditions: 1-PROPELLER rotates in ANTICLOCKWISE direction when seen from front end and Aeroplane turns towards LEFT. 2- PROPELLER rotates in ANTICLOCKWISE direction when seen from front end and Aeroplane turns towards RIGHT. 3- PROPELLER rotates in ANTICLOCKWISE direction when seen from rear end and Aeroplane turns towards LEFT. 4- PROPELLER rotates in ANTICLOCKWISE direction when seen from rear end and Aeroplane turns towards RIGHT.
A shaft has three eccentrics of mass 1kg each. The central plane of the eccentrics is 50 mm apart. The distances of the centers from the axis of rotation are 20 mm, 30 mm, and 20 mm and their angular positions are 120 degree apart. Find the amount of out-of-balance force and couple at 600 rpm. If the shaft is balances by adding two masses at a radius of 70 mm and at a distance of 100 mm from the central plane of the middle eccentrics, find the amount of masses and their angular positions. (Use graphical method for solution)
The mass of the A gear is 10 kg and the turning radius is 200 mm. Of gear Bits mass is 3kg and the turning radius is 80 mm. When the system is stationary to gear B. Moment of 6 N.m is applied. By neglecting friction;Find the tangential force from gear B to gear A.
Using the equilibrium concept, calculate the magnitude of F1 and its direction ф as shown in the Figure? Help me fast so that I will give Upvote.
Dynamic Forces Analysis:- Present a clearly labelled free body diagram for each rod and the slider;- Calculate the magnitudes and directions of all reaction forces at the instant shown using accelerations obtained in acceleration analysis part;- Calculate the instantaneous torque, T, required to drive the mechanism at the instant shown.
Find the mass-radius products and the angular location needed to dynamically balance the system using the correction plane A and B
1)Calculate the velocity of the arm, observed by a stationary person on the ground.2)Draw the FBD of the combined body (crane body, arm and load).3)Is the combined body stable? Why?4)Calculate the moment of the following, about wheel A,i) combined crane bodyii) load mass5)Which combined body’s component(s) will not fail? Why? (Hint: The crane was initially in equilibrium.)6)What are the various limits (maximum or minimum) for the combined body to be stable? Explain why.