elementary surveying A heavy 50-m tape having a cross-sectional area of 0.07cm² has been standardized at a tension of 6.4kg. Assume E = 3.20x10⁶ kg/cm². 1.Determine the elongation of the tape if a pull of 15kg is applied. 2.Determine the actual length of the tape.

elementary surveying A heavy 50-m tape having a cross-sectional area of 0.07cm² has been standardized at a tension of 6.4kg. Assume E = 3.20x10⁶ kg/cm². 1.Determine the elongation of the tape if a pull of 15kg is applied. 2.Determine the actual length of the tape.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate the magnitude of a uniformly distributed load (in addition to the beam's) which will cause...

A: Given : Width of web, Bw = 250 mm Width of bottom, Bb = 500 mm Width of flange, Bf = 750 mm Heigh...

Q: Find static indeterminacy for all structures please. Ns, Nse(exterior), Nsi(interior)

A: Given data in question Trusses To find out external static indeterminacy Internal static indeterm...

Q: The cross-sectional area of an aluminum bar is 170 mm?. It carries an axial loads at the positions a...

A: Given Area, A=170mm2 E= 80GGpa = 80x109N/m2= 80x103N/mm2 Formula used deformation = P*L/A*E p- load ...

Q: The solid aluminum shaft ABCD carries the three torques shown. (a) Determine the smallest safe diame...

A: Given: The allowable shear stress is 30 ksi. The shear modulus G is 4 x 106 psi. Consider the figure...

Q: Select all true statements. The advantage(s) of using two primers initiated at the same time is(are)...

A: statement wise explanation whether it's true or false with its reason is explained below. defining p...

Q: From the figure below, a shaft consists of different sections. Bar (a) is a hollow bar and has an ou...

Q: The soil is uniform if the coefficient of uniformity Cu close to: O 1.2.0 O 2.1.5 O 3.0.1 O 4.1.0 QU...

Q: True or False 1.) In a statically determinate structure, the number of independent unknowns must be...

A: True or false of the statements based on the explanation are given below

Q: Using LRFD and A-50 steel, determine the maximum load Pu that the system below can carry. Assume wel...

Q: The figure below shows a bracket plate to transmit a reaction of 150 kN at an eccentricity of 95 mm ...

Q: 4.10 PROBLEMS 4.1 Calculate the maximum axial load below. Materials are, C20 and materials. (a) Sect...

A: Given Data; 400*400 for both sections.

Q: Contractor X is developing his bidding strategy against contractor Y. The ratio of Y's bid price to ...

Q: Given data : Force=3 N Work done=18 Joule Determine displacement

Q: Calculate the shear force and bending moment for the beam subjected to the loads, then draw the shea...

Q: A cantilever beam is propped at the free end and carrying a uniform load of 400 kN/m throughout the ...

Q: A rectangular beam has a width of 375mm and has an effective depth of 450 mm. f'c = 25 MPa, Fy = 300...

Q: Self-healing concrete. Explain why that strategy and how it can help in the product development pro...

A: Strategy behind self healing concrete,

Q: A shaft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer d...

Q: The network of a small construction project awarded to a contractor is shown in the following figure...

Q: QUESTION 9 A 72 cm3 sample of moist soil weights 141.5 g. When it is dried out in an oven, it weighs...

Q: What will be the design bending strength for a laterally supported beam ISMB 300 of plastic section?...

Q: hormal deptr nom

Q: In 2007 the average growth of the global population was 1.2 percent per year. (a) Determine the doub...

A: Using the given average growth rate of 1.2% per year we can calculate the time expected for the glo...

Q: 1. From the video, the following data were obtained. a. Mass of SSD Sand = 505.0g b. Mass of pycnome...

A: For 1st sand, The saturated surface dry weight of the sample S =500 g Weight of pycnometer full of ...

Q: Construct Free Body Diagrams (FBD) of typical 12' and 16' joists and the interior beam along grid li...

A: According to given data Construct Free Body Diagrams (FBD) of typical 12 and 16' joists and the int...

Q: From the beam shown below: Compute for the Reactions and Draw the Shear and Moment Diagram under the...

A: Compute for the Reactions and Draw the Shear and Moment Diagram under the Beam

Q: 0/Derive the double armature 1. equation. As stress As

Q: 150 kN El is constant 3m 60° 200 kN 2 panels at 4m 8m

A: Method of joints: Method of joints is one of the methods which is used to solve unknown forces actin...

Q: Use the ratio an+1 -to determine if the sequence an {nbd is strictly increasing or strictly decreasi...

A: For the given sequence,

Q: Explain 'hydrologic equation

Q: 1. The connection shown consist of 10-A490 bolts and isattached to the column flange. The bolts are ...

Q: Ontario Building Code 2012 (Div. B-Part 9): Determine the dimensions of a 'landing' required of a ra...

A: Given data, Turning angle of ramp = 45o Occupant load = 200

Q: 32. Find the present value in pesos, of a perpetuity of Php 15000 payable semi-annually if money is ...

A: Present value is as below,

Q: Use the conjugate beam method to determine the slope at point A and the deflection at point Cof the ...

A: Given: Beam with point loads Conjugate beam is to be drawn E = 200 GPa I = 1080 *10^6 mm^4, 2I = 208...

Q: Determine the theoretical nominal moment capacity of the beam shown if fy = 420 MPa and fc' = 28 MPa...

A: Given - Fy = 420Mpa F'c = 28 Mpa To find-Nominal moment capacity of beam

Q: 1000 kg 200kg/m A C - 3m- 6m R1. R2

A: Given Data : length of AC = 6m length of BC = 3m at point B load = 1000 kg at section BC unifomly lo...

Q: What is oMn for W8x24 - A36 steel in lb-ft for: a) 15 ft b) 30 ft

Q: Determine the force in each member due to dead load, and rain loads.

Q: Determine the (x, y) coordinates of the centroid of the shaded area shown in the figure below. y D-8...

Q: A landfill project requires 5000 m3 of compacted soil. The void index specified for the compacted la...

A: Given : 5000 m3 of compacted landfill void ratio = 0.7 Gs = 2.6

Q: ane freeway (three lanes in each direction) in a scenic area has a measured free-flow speed of 55 mi...

Q: 3. Using Virtual Work, solve for the maximum PLL that a W 21x57 beam with a simple span length of 11...

Q: Given data : Water content%3D0.3 Void ratio=0.25 Specific gravity=2.7 Determine degree of saturation

A: This question is related with geotechnical engineering . In this question we are provided with value...

Q: er for fatigue cracking a

A: A binder ordered PG - 58-28 would meet the expected actual properties at an asphalt temperature as ...

Q: Determine the direct runoff, the D-index, and the excess rainfall hyetograph for the storm given bel...

A: DRH=Direct runoff hydrograph we have to determine ϕ-index here and excess rainfall for the hyetograp...

Q: A six-lane freeway (three lanes in each direction) has regular weekday users and currently operates ...

A: Given: The width of the lane is 11 ft. The width of the right-side shoulder is 4 ft. The percentage ...

Q: A bridge column carries a downward factored ultimate load of 310 kN and a service load of 200 kN. It...

A: Given: The ultimate load is 310 kN. The service load is 200 kN. The OCR is 2. The value of Su is 250...

Q: briefly the concept behind limiting the amount of tension steel reinforcement in a reinforced concre...

Q: A W 12 x 50 steel wide-flange beam and a segment of a 4-inch thick concrete slab (see figure) jointl...

A: Given data: I section w 12×50 with following properties. IXX=391 in4A=14.6 in2d=12.2 in Concrete sla...

Q: A butt joint is bolted using A325 bolts with a diameter of 22mm, with threads excluded from shear pl...

Concept explainers

Methods of Surveying

Surveying is the practice to determine the relative three-dimensional positions of various points on the earth’s surface. This is done by computing the vertical and horizontal distances, angles between the points, collecting the observations, and plotting them on a map of any appropriate scale. Accuracy can be achieved by using the latest instruments like a theodolite, tachometer, etc. Leveling is a subdivision of surveying where the objective is to locate the elevation of objects considering a datum level.

Question

elementary surveying

A heavy 50-m tape having a cross-sectional area of 0.07cm² has been standardized at a tension of 6.4kg. Assume E = 3.20x10⁶ kg/cm².

1.Determine the elongation of the tape if a pull of 15kg is applied.

2.Determine the actual length of the tape.

Determining the relative position of points on the Earth's surface and measuring the angle and distance between them in order to calculate the required parameters such as elevation and enclosed area.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The measured length of an inclined distance was recorded to be 417.698 m long. The difference in elevation between the initial and end points was found to be 1.72 m. The 25 m tape is of standard length at temperature 13 ˚C. During measurement the temperature reading was 20˚C and the tape was supported at both ends with an applied pull of 72N. The tape has a weight of 0.549 kg/m. (K=0.0000116 m/˚C) Determine the corrected horizontal distance (in meters)
elementary surveying A 30-m tape weighing 1.5kg is of standard length under a pull of 6kg, supported for full length. The tape was used in laying a line 2,893.4m long on smooth level ground under a steady pull of 17kg. Assuming E = 3.2x10⁶ kg/cm² and the unit weight of steel to be 7.9x10⁻³ kg/cm³. 1.Determine the correction for increase in tension. 2.Determine the correct length of the line measured.
Q1/Find the horizontal displacement at C . and @y by using Virtual Work Method, i you know E - 200 GPa, I - 25°(10% mmé , (P KN)
A 50m tape weighing 0.03kg/m is used to measure distance AB. The tape is supported at both end points and at its midspan and then applied tension is 6kg. Determine the total sag correction if the measured distance is 1,320.50m.
CORRECTION DUE TO SAG. A 30-m steel tape weighing 0.04 kg/m is constantly supported only at its endpoints, and used to measure a line with a steady pull of 8.5kg. If the measured length of the line is 2465.18 m, determine the correct LENGTH OF THE LINE.
Note: q = 19 kN/m P = 85.50 kN
A line is measured on a uniform slope with a 30 m steel tape pulled with a force of 5 kg and is found to be 575m long. The temperature at the time of measurement is 1 C. the tape is standardized at 17 C and at a pull of 5 Kg. the different of level of the two ends of the line is 10m . Determine the horizontal distance between the two ends of the line. Coefficient of expansion is 11.5 X 10^-6 degree centigrade (C) .
What must be the pull in a (7)(10) meters tape in order to eliminate the sag and temperature correction, given the following? a = 7x10% m? E = 2x101 N/m? Weight of tape, 11 N Po = 10kg To = 22°C T = 20°C K= 0.0000116/°C The tape length is supported at both ends. Fundamentals of surveying
The taped distance of a line is 198.175 m using a 50 m steel tape weighing 2.4 kg with a cross sectional area of 0.036 cm2 at 32°F with a pull of 8 N is applied, supported at 20 m interval during the measurement. The angle of the tape during measurement is 11°20′. The tape is exactly 50 m at a temp of 28°F at standard pull of 5 N, find the following: a) Correction due to combined correction of the tape b) Correction due to slope c) The correct horizontal distance of the line
A 30-m tape is supported only at its ends under a steady pull of 8-kg. If the tape weighs 0.91-kg, determine the sag correction and the correct distance between the tape ends of the tape. Illustrate.
A 30-m steel tape weighing 0.04 kg/m is constantly supported only at its end points, and used to measure a line with a steady pull of 8.5 kg. If the measured length of the line is 2465. 18 m, determine the correct length of the line. Please include the complete solution
The crest gate shown consists of a cylindrical surface which AB is the base, supported by a structural frame hinged at C. It is retaining water on one side. The length of the gate perpendicular to the paper is 8.29 m. Use R = 14 meters, and θ = 42°. Determine the distance (in meters) of the vertical component of the hydrostatic force measured from the hinge at C. Round off to three decimal places.