engine fuel tank was completely filled with gasoline before testing. After 4 hours of continuous test, 3.7 liters of fuel was used to completely refill the tank. Test has shown that the engine shaft power was 10 hp. What is the specific fuel consumption of the engine (g/kW-h)?

engine fuel tank was completely filled with gasoline before testing. After 4 hours of continuous test, 3.7 liters of fuel was used to completely refill the tank. Test has shown that the engine shaft power was 10 hp. What is the specific fuel consumption of the engine (g/kW-h)?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter2: Matter And Energy

Section: Chapter Questions

Problem 26RQ: How many Btu of heat can be produced by 4 kWh ofelectricity?

See similar textbooks

Related questions

Q: For an ideal gas, a constant pressure line and a constant volume line intersect at a point, in the t...

Q: 0 kmph and the vehicle is to be stopped at a distance of 50 m. Take the diameter of the vehicle tyre...

Q: Two vertical forces are applied to a beam of the cross-section shown. Determine the maximum tensile ...

Q: meter. ler A:B:C has a speed ratio of 3:2:4 are externall ter distance between cylinder A and C is 3...

Q: Water drains from a pressurized tank (50 kPa gage) through a 0.1m-diameter pipe system at a rate of ...

A: Given:d=0.1 mQ=0.0371 m3/sρ=1000 kg/m3μ=1.12*10-3 Ns/m2

Q: Pls show the edge view of two triangles in a single reference plane...kindy explain the steps

A: Solution: Given Data:

Q: Which of the following is a unit of fundamental quantity A) meter per second B) gram (c) Kelvin (D) ...

A: 1. Unit of Fundamental Quantity : The fundamental quantity does not depend upon another quantity The...

Q: A rubber block is placed between two rigid walls where a load of P = 60 kN is applied on top as show...

A: GivenP=-60kN compressive

Q: Using the DE-Goodman criteria and a design factor of 1.5, calculate the diameter based on the shaft...

Q: An isosceles triangular plate of base 4 m and altitude 4 m is immersed vertically in an oil of sp. g...

A: The total pressure is defined as the force exerted by a static fluid on the surface either plane or ...

Q: The block A starts at y=0 and then moves upward due to the force, F, in the cable. The block has an ...

Q: A circular bar of L 570mm length is supported freely at its two ends. It is acted upon by a central ...

Q: Cantilever circular shaft is loaded by concentrated couples. М1 М2 Мз M4 A l2 14 Given: /1= 1,61; lz...

Q: ᴄᴀʟᴄᴜʟᴀᴛᴇ ᴛʜᴇ Qᴜᴀɴᴛɪᴛʏ ᴏꜰ ʜᴇᴀᴛ ᴄᴏɴᴅᴜᴄᴛᴇᴅ ᴘᴇʀ ᴍɪɴᴜᴛᴇ ᴛʜʀᴏᴜɢʜ ᴀ ᴅᴜʀᴀʟᴜᴍɪɴ ᴄɪʀᴄᴜʟᴀʀ ᴅɪꜱᴄ 127 ᴍᴍ ᴅɪᴀᴍᴇᴛᴇ...

Q: Identify the various operations performed during its rice production in Japan? For each operation, d...

A: Paddy rice is the staple food in japan . Since japan's mild and humid climate is good for growing cr...

Q: 4. The analyst in the Red Diamond Electronics Company wishes to assign a number of like facilities t...

A: Given data: l=0.34+0.26=0.6 minutesm=1.48 minutesC1=$12 per hourC2=$18 per hourw=0.06 Need to determ...

Q: A welded joint of circular shaft as shown in figure is subjected to an eccentric load of 2.5 kN. If ...

Q: Q14. As shown in the image below, the force acting on the box is F = (C · t2) N,where constant C = 3...

A: Given:F=C.t2C=3t=0 to t=1.4 sec

Q: Hazel stands on the edge of a lookout admiring the view of a waterfall. The lookout is supported by ...

A: Givenmass m=60kgg=9.81m/s2θ=700

Q: D,I 3.4-5. Use the graphical method to solve this problem: Minimize Z = 15x, + 20x,, subject to X + ...

Q: Define the meaning and significance of the ductile to brittle transition temperature (DBTT). Identif...

A: DBTT: A temperature at which there is abrupt change in the ability of material to absorb force witho...

Q: Le mathematical model by considering the man body, and restraints for a vibratio: -Windshield Instru...

A: a human body and controlled framework at the time vehicle crash are displayed in the given figure

Q: For the same system, write equations of motion in the matrix form: ku k12 :) m12 ) = 0 m11 m21 m22 k...

A: Given: →m11m12m21m22x¨y¨+k11k12k21k22xy=0→m11x¨+m12y¨m21x¨+m22y¨+k11x+k12yk21x+k22y=0so→m11x¨+m12y¨+...

Q: Which of the following is the Camot Efficiency? work input /work output (input temperature - output ...

A: Carnot efficiency: It is maximum efficiency of a thermodynamic cycle. Heat input and heat output is ...

Q: A greenhouse system consists of a controller for controlling the system, sensors for detecting the e...

A: Nursery, additionally called glasshouse, building intended for the security of delicate or unavailab...

Q: The temperature at which the vapor pressure of a liquid equals the external pressure is known as? Se...

A: Vapour pressure determines the tendency of a liquid to change into its vapour phase.

Q: What type of axle housing resembles a banjo?

A: Given Data : Banjo

Q: A in.x 3 in. bar of 1045 hot-rolled steel is loaded by a tension force varying continuously from Pma...

Q: 1- The steady state temperature profile for a wire carrying current is R* (1- G) gR T(4) = + + T; %|...

Q: titude of 10000m. Determine the gage pressure e of plane with a velocity of 274 m/s. The density

Q: mechanical vibrations Show one example. Summarize the method. How would you solve these application...

Q: A reaction turbine is working under a head of 10 m with an average discharge of 700 m/min. The overa...

A: Given data as per question Head =10 m Average discharge =700 m3/min Overall efficiency =90% Speed of...

Q: PROBLEM 2 This force-couple system is to be replaced by an equivalent system consisting of the follo...

Q: Dexit Dentrance U exit lUentrance u(x) X = 0 X = L

Q: /elop a ithematical ind plow sh considering the mass, elasticity, and damping of the tires, shock ab...

A: A tractor and plow Damping of tires eventually leads to an increase in the temperature of the tire a...

Q: Given: Tdb = 46°C , RH = 30% Determine the air properties using the psychrometric chart (show solut...

A: To find : air properties using psychrometric chart, plot them and make projections of them

Q: A steel shaft of 75 mm diameter and 250 mm long turned on a lathe. Speed of spindle = 2 m/s, feed = ...

A: Turning is one of the most common operations. surfaces of revolution are generally produced by this ...

Q: a) A part for a specialist mining machine is made from solid A992 structural steel with a diameter o...

A: Solution: Given Data: d = 25 mm

Q: ith 3% moisture, 2.5 kg of steam has an enthalpy of 6600 kJ. It is heated at constant pressure to a ...

Q: 32. Velocity profile for turbulent flow in smooth circular pipes may be empirically expressed as V(r...

A: Velocity profile is integrated to get volume flow rate and from there average velocity is calculated...

Q: Which factors affect the mechanical properties of a material under applied loads?

Q: A piston cylinder contains 0.72 kg of air initially at 600 kPa and 225 °C, now the air expands in a ...

A: GIVEN DATA- MASS m=0.72kg P1=600KPa T1=225'C=225+273=498K P2=125KPa T2=25'C=25+273=298K WE HAVE TO C...

Q: f flyewheel is collached fo to keep its fefational speed between engice 9o radls tollorádl /s f Ahe ...

A: GIVEN DATA- ∆E=0.01KJ ω1 = 110 rad/s ω2 = 90 rad/s WE HAVE TO FIND MASS MOMENT OF INERTIA

Q: A small sphere of density rho, diameter D and heat generation gdot0 is exposed to a fluid at Tinf wi...

A: We additionally accept a consistent hotness move coefficient h and disregard radiation. The definiti...

Q: A crate is supported by a cable and spring. The spring has unstreached length of 2m. Calculate stiff...

A: Given:m=40 KgL=2 m

Q: 1) Two parallel shaft connected by pure rolling turn in the same direction and having a speed ratio ...

A: Given:SR=2.75dp=22 cm

Q: Determine the force in members CF of the truss. State if the members are in tension or compression. ...

A: GIVEN DATA- A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN MEMBER CF

Q: What is Line J? ARROWHEAD .35mm 7.0- HIDDEN LINE 3mm K 01 5 0,5- 3. NOTE 5mm H. E. ABCO

A: Answer: The line "J" is called "section line". Therefore, the correct option is (C).

Q: 2. Find the Moment about A and B for the forces acting on the body shown below. The forces acting at...

A: Moment about a point is the product of force and perpendicular distance between point and force. It ...

Q: e number of instant center and locate all of them using IC Circle method. ea software to visualize t...

Question

An engine fuel tank was completely filled with gasoline before testing. After 4 hours of continuous test, 3.7 liters of fuel was used to completely refill the tank. Test has shown that the engine shaft power was 10 hp. What is the specific fuel consumption of the engine (g/kW-h)?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The density of jet fuel is 760 kg/m3. Determine the specific weight and specific gravity of the fuel.
A foreign manufacturer lists the fuel consumption for a new automobile as 15kilometers per liter (km/L). Determine the fuel consumption in miles per gallon
If you rent a car, you can (1) return it with a full gas tank, (2) return it without filling it and pay $5.75/gallon, or (3) accept a fixed price of $60 for gas. The local price is $3.50/gallon for gasoline, and you expect this car to get 25 miles per gallon. The car has a 16-gallon tank. What choice should you make if you expect to drive: (a) 150 miles? (b) 300 miles? (c) 450 miles? (d) How do your answers change if stopping at the filling station takes 20 minutes and your time is worth $15/hr?
A Boeing 767 due to fly from Montreal to Edmontonrequired refueling. Because the fuel gauge on the aircraft was not working, a mechanic used a dipstick todetermine that 7682 L of fuel were left on the plane.The plane required 22,300 kg of fuel to make the trip. Inorder to determine the volume of fuel required, thepilot asked for the conversion factor needed to converta volume of fuel to a mass of fuel. The mechanic gavethe factor as 1.77. Assuming that this factor was in metric units the pilot calculated the volume to beadded as 4916 L. This volume of fuel was added andthe 767 subsequently ran out the fuel, but landed safelyby gliding into Gimli Airport near Winnipeg. The errorarose because the factor 1.77 was in units of pounds perliter. What volume of fuel should have been added?
Specific Gravity of Water=1.0 SG of Mercury= 13.6 SG of n-Octane=0.655
A 200-hp engine can deliver, in SI units, an average power of ____. (1 hp = 746 W)
If an engine that throws 200 kW of heat energy into the atmosphere produces 150 horsepower (hp), what is the efficiency of this engine? TIP: Horsepower is not included in the international unit system, you must convert it to kW.
The dry exhaust gas from oil engine has the following gravimetric analysis (by mass basis): CO2 = 22.1%, O2=3.7%, N2=74.2%. Calculate the specific gravity of the flue gas if the molecular weight of air is 28.97 kg/kmol.
A tank having a volume of 1000 ft3contains 22 lb of CO2, 46 lb of O2 and 154 lb of N2. What pressure will be indicated by a pressure gage attached to the tank if the gas is at ambient temperature (80°F)?
Identify if the property of the following steam: Pressure Specific Volume Internal Energy MPa m3/kg kJ/kg 13 ? 1338
If you check automobile tire pressure on a cold morning before leaving home, and check it again after driving a few miles, would you expect the tire pressure to increase or decrease?
A child takes a helium balloon on a plane from Denver (with an air pressure of 0.83 atm) on a cool day when the temperature is 20.0oC to Boston (at sea level, with an air pressure of 1.0 atm) where the temperature is 5.0oC. Assume that no gas escapes from the balloon during the flight. What is the volume of the balloon in Boston, relative to its size in Denver? Group of answer choices The volume in Boston is 0.79 times the volume in Denver. The volume in Boston is 0.20 times the volume in Denver. The volume in Boston is 0.87 times the volume in Denver The volume in Boston is 1.3 times the volume in Denver. The volume in Boston is the same as the volume in Denver.