Establish metal and non-metallic material properties using destructive and non-destructive test methods

Q: Cold working of metals will give better final properties than hot working. Select one: True False

A: Hot and cold working: Important difference between these processes is hot working is done at high…

Q: Develop knowledge of the properties of ferrous metals to consider when making material selection…

A: Properties of ferrous metal 1)cast iron can be cast in a mould 2)High carbon steel hard but brittle…

Q: The ability of a material/metal to resist the external forces without breaking or yielding is called…

A: The ability of a material/metal to resist the external forces without breaking or yielding is…

Q: List TEN (10) mechanical properties that a mechanical engineer should consider when selecting the…

A: The physical properties that material shows when the forces is applied on it is called mechanical…

Q: 1. hot-rolled bars of AISI 1020 and 1040 steel 2. stainless steel sheets of Type 430 ferritic…

A: Solution:: Ans-1  The separation of metal parts occurs according to two different processes: ferrous…

Q: Cold working of metals will give better final properties than hot working. Select one: True False

A: Solution:

Q: When a material is subjected to repeated stresses it will not fail without any prior indications.

A: When we apply repeated load on a material, then the properties or strength of the material will…

Q: 8.11 After consultation of other references, write a brief report on one or two nondestructive test…

A: Ultrasonic nondestructive testing technique Ultrasonic testing (UT) refers to a group of…

Q: Explain the different properties and uses of materials. Give at least 2 usages (particularly in the…

A: Different properties and uses of materials has been given in step-2.

Q: Process used to improve fatigue resistance of the metal by setting up compressive stresses in its…

A: Cold Peening or Shot Peening: It is a cold work process used to prevent parts from fatigue and…

Q: What is creep and stress rupture testing?

A: Creep and stress rupture testing: The creep and stress rupture testing is used to check the…

Q: Describe the six most common tests used to identify material properties

A: Most common tests used to identify material properties:-

Q: Discus the impact of each defect on material properties.

A: The main defect in a material are point, line, and surface defects. These defects are crystalline…

Q: Describe the non-destructive testing processes – dye penetrant, magnetic particle, ultrasonic and…

A: Non-Destructive Testing Processes is an industrially used measuring and inspection method to assess…

Q: The ability of a material to undergo large permanent deformation with the application of a tensile…

A: Elasticity: It is the ability of the material which allows to return to its original shape and size…

Q: The magnitude of the modulus of elasticity is a measure of the resistance to separation of adjacent…

A: Answers (1) T (2) F (3) T

Q: Describe the working and environmental conditions that lead to failure for a product made from…

A: The auxiliary judgment of conventional FRP components in destructive situations is as a rule…

Q: Questions Conceptual Questions 1. List five important consequences of corrosion.

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: A non-destructive test is any examination of an object in any manner which will not impair the…

A: True , A non-destructive test is any examination of an object in any manner which will not impair…

Q: Identify standards for the classifications of metals and alloys

A: Solution: Standards Classification of Metals: a) Classification by Iron content:  most common way to…

Q: raw a potential to failure curve and explain its characteristics

A:

Q: (a). Create a table of values of any 5 mechanical properties of any carbon steel metal. Define the…

A: The selected material is AISI 1045 carbon steel. The mechanical properties of the material are shown…

Q: What is the importance of knowing the Mechanical Properties of a certain kind of Metal?

A:

Q: Differentiate between the fatigue test and tensile test.

A: On the basis of Tensile Test Fatigue Test Determination For determining the specimen…

Q: Thermal Analysis - Material Characterisation  State the 3 criteria that must be met to qualify a…

A:

Q: It is the lightest metal for general engineering applications and possesses good vibration damping…

A: Magnesium

Q: List four measures that may be taken to increase the resistance of fatigue of a metal alloy

A: Given:- Metal alloy To find: Measures to increase the resistance of fatigue

Q: The shear strength of a metal is commonly determined in which one of the following tests: Group of…

A: The below table describes the determination of corresponding stress for a corresponding test.…

Q: Check the incorrect statements. a) As the thickness of the specimen increases, the fracture…

A:

Q: Describe an example each of the following tests used for identifying metals and indicate whether…

A: Physical test – physical test on the metal is performed to identify the physical properties of the…

Q: Metal work: What are possible sources of error in trying to obtain a specific hardness or strength?

A:

Q: Describe six common mechanisms of failure

A:

Q: Three factors that should be considered in designing laboratory test to assess the mechanical…

A: Mechanical testing is a standard and essential part of any design and manufacturing process. Whether…

Q: After consultation of other references, write a brief report on one or two nondestructive test…

A: Non destructive testing:-  Nondestructive testing is one quality control function and complements…

Q: Yield strength, ultimate tensile strength, linear coefficient of thermal expansion, modulus of…

A: 1) true  2) true  3) false  4) false

Q: is the property of a metal which resist the external forces to scratch. a. strength b. Creep C.…

A: hardness is the property of a metal that resists plastic deformation or indentation, penetration it…

Q: Create an infographics regarding the Mechanical Properties of Metal. Provide short and brief…

A: given;   Create an infographics regarding the Mechanical Properties of Metal. Provide short and…

Q: Q17: chemical properties such as: A: density b: impact c: hardness d: corrosion

A: Chemical properties: The properties of the substance which gives a chemical reaction,hence changes…

Q: Why is it important to make standards for the different building/engineering materials? (Tensile…

A: All things considered, we've been building two-stories wooden homes for millenia, so what's the…

Q: Aside from iron and carbon this metal constituents adds mechanical properties to the metal Some…

A:

Q: Which would be the most likely to measure for an inflated baloon? A. Shear modulus b  bulk modulus…

A: Which would be most likely to measure for an inflated balloon....... First and foremost what is…

Q: want a set of examples of deflection that occurred in nature without human intervention

A: Example is given below:

Q: Brittle materials have more impact strength compared to ductile materials. Select one: O True O…

A: Impact quality is the capability of the fabric to resist a abruptly connected stack and is…

Q: The cold worked components results in uniform properties of the metal. Select one: O True O False

A: There are three types of working condition during production process. These are cold working,…

Q: Metal working Fe-C: What are possible sources of error in trying to obtain a specific hardness or…

A: Solution is attached below

Q: After consultation of other references, write a brief report on one or two nondestructive test…

A: A brief report on Non-Destructive test techniques used to detect and measure the surface or internal…

Q: -High-purity metals are almost always softer and weaker than alloys composed of the same base metal

A: High purity metals are almost always softer and weaker than alloys composed of the same base metal.…