Estimate the coefficient of permeability for a uniform sand where a sieve analysis indicates that the D10 size is 0.15 mm (by Hazen formula). The particle-size distribution curve for a sand indicates that the D15 size is 0.19 mm. If the sand deposit is in the dense or compact state, estimate the coefficient of permeability.

Estimate the coefficient of permeability for a uniform sand where a sieve analysis indicates that the D10 size is 0.15 mm (by Hazen formula). The particle-size distribution curve for a sand indicates that the D15 size is 0.19 mm. If the sand deposit is in the dense or compact state, estimate the coefficient of permeability.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter5: Soil Compaction

Section: Chapter Questions

Problem 5.13P

See similar textbooks

Similar questions

Estimate the coefficient of permeability for uniform sand where a sieve analysis indicates that the D10 size is 0.15 mm (by Hazen formula). Also, the particle-size distribution curve for another sand indicates that the D15 size is 0.19 mm. If the sand deposit is in the dense or compact state, estimate the coefficient of permeability.
A sample of sand is subjected to a constant head permeability test. The sample diameter is 60 mm and its length is 130 mm. Under an applied head of 60 cm, 119 cm³ of water flows through the sample in 5 minutes. Determine (a) the coefficient of permeability, and (b) the discharge velocity.
Situation 2 - For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen = 16 cm Diameter of specimen = 96 mm Constant Head Difference = 50 cm Volume of water collected in 4 min = 420 cc Void ratio of the soil specimen = 0.55 a. Determine the seepage velocity in m/min. Round off to four decimal places. b. determine the discharge velocity in m/min. Round off to four decimal places.
Estimate coefficient of permeability for a sand deposit where field testing indicates that the in-situ e=0.50 and D10=0.55 mm and Cu = 8. Using the information from (1) determine the D60 particle size using the Kozeny-Carman equation.
2. Situation 2 - For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen = 16 cm Diameter of specimen = 96 mm Constant Head Difference = 50 cm Volume of water collected in 4 min = 420 cc Void ratio of the soil specimen = 0.55 a. Determine the hydraulic conductivity of the soil in m/min. Round off to four decimal places. b. Determine the discharge velocity in m/min. Round off to four decimal places. c. Determine the seepage velocity in m/min. Round off to four decimal places.
A modified proctor compaction test is performed on a sample of silty sand in a 150 mm diameter mold. The maximum dry unit weight is 19.6 kN/m3 and optimum water content is 11%. If the specific gravity solids is 2.65, draw the three-phase diagram of the sample in the mold and calculate all volumes and weight for that sample. What is the degree of saturation?
Given: Weight of wet sand sample (Ww) = 500 g Weight of Dry sand sample (Wd) = 490 g Moisture content of the given sand is: 5% 4% 2% 1%
The in situ dry density of a sand is 1.68 Mg/m3. The maximum and minimum dry densities, determined by standard laboratory tests, are 1.84 Mg/m3 and 1.47 Mg/m3, respectively. Determine the relative density of the sand. The particle specific gravity of the sand is 2.65. (Density of water 1 Mg/m3)
Problem: For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen - 16 cm Diameter of specimen - 9.6 cm Constant head difference - 50 cm Volume of water collected in 4 min - 420 cc Void ratio of the soil specimen - 0.55 A.) Determine the hydraulic conductivity of the soil in cm/sec B.) Determine the discharge velocity in cm/sec C.) Determine seepage velocity in cm/sec Problem: For a falling head permeability test, the following are given: Length of Soil Specimen - 200mm Area of Soil Specimen - 1000mm^2 Area of Stand pipe - 40mm^2 Head Difference at time t = 0 min - 500mm Head Difference at time t = 3 min - 300mm A.) Compute hydraulic conductivity of the soil in cm/sec B.) Compute the seepage velocity if the porosity is 0.25 in cm/sec C.) What is the head difference at time t = 100 sec in mm
John is analyzing a silty sand. it has a void ratio in loosest condition equal to 0.87 and a void ratio of 0.36 in the densest condition. If the relative density of the silty sand is 77%, compute the in-situ porosity.
a. What is the compacted dry density?b. What is the field water content?c. What is the relative compaction?d. Does the test meet specifications?e. What is the degree of saturation of the field sample?f. Plot the laboratory curve and the results of the sand cone test on the same graph. Show the limits of the acceptable range.
Question 40 The results of a constant head permeability test for a fine sand are as follows: Diameter of the sample = 25 cm Length of sample = 80 cm Constant head difference = 77 cm Time of collection = 388 secs Weight of water collected = 340 grams Find the seepage velocity in cm/min. if the void ratio is 0.49. Round off to four decimal places.