Estimate the fallout level if the specifications are 16 ± 5. Estimate ?? and interpret this ratio.
Q: Determine the correct length of a line reduced to the mean sea level when the recorded length with a…
A: Given data : Problem from Surveying: We are asked to determine the correct length of a line reduced…
Q: The lower sand layer in the soil profile shown below is in an artesian condition. Calculate: 2 a)…
A: Given data : It is a multipart problem from Soil Engineering/Mechanics or Geotechnical Engineering.…
Q: 4. Estimate the profile of vertical effective stresses for Zw= 100m and for Zw=3000m. Compare…
A:
Q: From the following cross-section notes, complete the table below. Use prismoidal method. Road bed…
A:
Q: 4. The beam shown in figure below (W 410 x 46.1) has continuous lateral support of both flanges. The…
A: Given: Section: W 410 x 46.1 fc = 35 MPa A36 steel: fy = 250 mm fu = 450 MPa
Q: QUESTION 6 Determine the long chord, PC to PT, of a reverse curve given the following properties: 1₁…
A:
Q: Mr. Burns is having a new convenience store built on the southwest corner of Maple Drive and 3rd…
A: Given, Construction project situation
Q: 1. The distance travelled by a vehicle during perception-reaction time is 55.56m. If this vehicle is…
A:
Q: Question 5 A rectangular presressed concrete beam of span 15 m and width 500 mm is loaded with a…
A: Given data- A rectangular prestressed concrete beam, Span L=15 m, Width b= 500 mm, live load = 30…
Q: 6
A:
Q: A curve of radius 250 ft and e = 0.08 is located at a section of an existing rural highway, which…
A: We have to find out the mnimum radius of curve for safe speed. We will use the formula R =…
Q: If the radius of a circular curve is 105.47 feet and one full station is 200 feet, what is its…
A: This question is related to the Simple curve from Surveying Engineering. Given Data - Radius of…
Q: Question- For a fully developed laminar flow of water (dynamic viscosity 0.003 Pa-sec) through a…
A: Given data- A fully developed laminar flow of water, Dynamic viscosity μ=0.003 Pa-sec, Radius of the…
Q: A container of volume 3 x 103 m³ weighs 10 N. Dry sand was poured to fill the container. The…
A:
Q: A deposit soil sample contains 50 grams of sand, 8.4 grams of gravel, 6.6 grams of air as void and…
A: As per honour code we have to answer first three parts of question . For rest part submit new…
Q: A 3 m long simply supported beam of uniformcross section is subjected to a uniformlydistributed load…
A: A simply supported beam of span 3 m supported at P and Q with hinge and roller respectively. A UDL…
Q: 1. A vertical pressure of 70 MPa is applied to an aluminum cube sample with a length of 10 cm on…
A:
Q: 80 KN -30 kN/m A 6m B
A: Concept Here we will calculate the reactions at each support using the equation of equilibrium.…
Q: Water Water
A:
Q: Draw the influence lines for the bar forces in members AB, BK, BC, and LK if the live load is…
A:
Q: Construction Management Questior The direct and indirect costs estimated by a contractor for bidding…
A: Given data- Direct cost DC = Rs 160000, Indirect cost IC = Rs 20000, Markup =10 % of the bid price.…
Q: 1 m 30 mm B 4- Determine the maximum allowable load P that can be applied to member BC without…
A: Given : F.S. = 3 Est = 200 GPa To Find : Determine the max. allowable load P that can be applied to…
Q: for B, it says moisture range. so I am expecting an interval. Can I ask how did 8.2 came?
A: This question is related to the Soil Mechanics from Civil Engineering. This is combined problem if…
Q: The perpendicular distance between tangents of a reversed curve is 10 m. The chord length from the…
A:
Q: Why must measurement models be evaluated before structural models
A: Context: Measurement and Structural models
Q: 3. For the statically indeterminate cantilever beam (EI is constant) shown in Figure 3 and using…
A: Given Propped cantilever beam with point load acting on it. Length=3mLoad,P=25 kNEI=10*106 N-m2…
Q: Which of the following does NOT belong to a risk assessment? O Risk estimation Exposure assessment O…
A: Brief concept introduction- Risk assessment- A risk assessment is a process used to determine which…
Q: Rigid member ABCD shown here is used to support a 2 kN weight. This member is 6-m-long. Steel (E =…
A: Given : E = 200 GPa Weight supported = 2 kN diameter = 0.5 cm length = 6 m To Find : Deflection of…
Q: 1. 8 kN 45° B L 8 kN 45° L D 60% E
A:
Q: du dt = = 3.6 - 0.06u where u is the vehicle speed in ft/sec. The vehicle is traveling at 45 ft/sec…
A: Given data- Speed-time relation- dudt=3.6-0.06u, To Find- Distance travelled, time to attain a speed…
Q: A water siphon having a constant inside diameter D of 4 in. is arranged as shown in the figure…
A:
Q: Given the following, solve for the radius of the curve: M = 25.988m • 1 = 54.939° NOTE: Solution not…
A: To determine: The radius of curve.
Q: 1 Gate AB is 2.0 m wide perpendicular to the paper and open to let fresh water out when the sea…
A:
Q: Electrical conductivity (EC) value of a saturated extract of soil is 13 m.mho/cm. Leaching…
A:
Q: Example 2 : Design a concrete mix to implement a concrete slab (exposed to sever conditions moisture…
A: Given, f'c = 30 MPa S = 4 MPa Density of aggregate = 1500 kg/m3 FM = 2.4
Q: How does concrete strength affected by Effect of materials and mix proportions?
A: The strength of concrete indicates the resistance of the structure. In the world of construction,…
Q: A live load 0f 80 KN/m moves on a simply supported girder of span 12m. The maximum bending moment…
A:
Q: Please
A:
Q: Determine the correct length of a line reduced to the mean sea level when the recorded length with a…
A: Answer Correct length of a line is given by Correct length = Measured length - Total corrections…
Q: Determine the normal stress in a ball, which has an outside diameter of 160 mm and a wall thickness…
A: Pressure (P)=84kPa = 0.084MPa Thickness (t)=3.6mm Outside diameter (D)=160mm Inside diameter (d)=…
Q: Describe and discuss in detail indirect waste and how is it handled?
A: Indirect waste- A drain pipe that exits a water pipe or fixture and empties into another waste pipe…
Q: 6. Draw the shear and bending moment diagrams of the beam loaded as shown in the figures below.…
A:
Q: 20 KN 15 m 5 kN/m 25 kN
A:
Q: An open tank is filled with a liquid that has a specific gravity of 1.154 and the liquid exerts a…
A:
Q: Write the V and M equation of the beams loaded as shown and the diagram. Then repeat the method…
A:
Q: a) With the context of town planning describe the importance of: 1. Natural resources 2. Economic…
A: Natural resources are substances that occur naturally and are valued in their largely unaltered…
Q: 4 m A AG= G 3 m 9 B 350 kN kN C 100 kN 2m 2m- 1. Find the forces acting on each member: (Round off…
A:
Q: A +4.90% grade meets a +1.55% grade at station 4+200 and elevation 605.568 m, 195-m curve, stakeout…
A: To calculate the station elevations, an equal tangent parabolic curve is given with the following…
Q: A body of dimensions 1-5 m x 1.0 mx 2 m, weighs 1962 N in water. What is the weight of the body in…
A: Given- Dimension of the body- 1.5 m×1.0 m×2 m, Apparent weight-Wapparent=1962 N,g=9.81 m/s2 It is…
Q: For the shown beam, determine the support reactions at pin A & roller B 600 lb/ft A 6 ft- B 3 ft-…
A: Given: A simply supported beam with one side overhanging where hinge at A and roller support at B.…
Estimate the fallout level if the specifications are 16 ± 5. Estimate ?? and interpret this ratio.
Trending now
This is a popular solution!
Step by step
Solved in 2 steps
- A two-story office building totaling 18783 ft2 is interpreted as a light hazard (200 ft2/sprinkler from Table 11.1). If black steel pipe is used, determine the riser size. Fill in the size of the pipe. If 2 1/2 in., input 2.5. Hint: You should first determine how many sprinklers are there using area / [200ft2/sq], and then check this table, and find the size of the pipe. This is a light hazard classification, and the material is steel. You should look at the left-most column.A two-story office building totaling 18783 ft2 is interpreted as a light hazard (200 ft2/sprinkler from Table 11.1). If black steel pipe is used, determine the riser size. Fill in the size of the pipe. If 2 1/2 in., input 2.5. Or see below. You should first determine how many sprinklers are there using area / [200ft2/sq], and then check this table, and find the size of the pipe. This is a light hazard classification, and the material is steel. You should look at the left-most column.Also calculate secondary losses with sudden narrowing
- Quick solution ???b) Looking into the future with mean temperature levels exceeding 2.50C above pre-industrial levels it is considered that the maximum size of the water drain pipe would increase by 4m3/second every decade . Provide a table of expected maximum drain loads over a period from 2030 to 2130 and plot this on a graph. You are advised to plot the maximum expected rainfall against pipe diameter.please avoid typing the answers- On a clear summer afternoon with a wind speed of 3.20 m/s, the particulate concentration was found to be 1,520 mg/m3 at a point 2 km downwind and 0.5 km perpendicular to the plume centerline from a coal-fired power plant. Given the following parameters and conditions, determine the particulate emission rate of the powerplant:
- A water tower will be built to store water produced for needed fire flow. The design of the water tank will be cylindrical with a bottom radius of 50 ft. The service area has 20 one-story warehouses; all warehouses are noncombustible structures, and their average floor area is 0.50 acre. The sum of exposure and communication factors is 0.60 for each warehouse. What will be the needed fire flow (in GPM)? What will be the volume of water (in m3) that needs to be produced and stored in the water tank? What will be the gage pressure (in psi) at the bottom of the water tank?Draw a hyetograph according to the rainfall heights measured at the end of each hour during an 8-hour rainfall.What is the contaminant plume, or simply plume?