Ex. 317. Determine the closed-loop steady-state error given a R(s) + E(s) >0----->| G(s) 1---+---> C(s) (a) unit step input, (b) unit ramp input, and (c) unit parabola input. G(s)=12/(s (s+14)) Also determine the (d) position constant, (e) velocity constant, and (f) acceleration | constant. If any value is infinite, enter 8. ans:6

Ex. 317. Determine the closed-loop steady-state error given a R(s) + E(s) >0----->| G(s) 1---+---> C(s) (a) unit step input, (b) unit ramp input, and (c) unit parabola input. G(s)=12/(s (s+14)) Also determine the (d) position constant, (e) velocity constant, and (f) acceleration | constant. If any value is infinite, enter 8. ans:6

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the root locus for the control system whose T.F. is given below,
Which row represent the most stable system and why? nyquist and root locus plot attached.
A system has the following characteristic equation: s + s + 3 + 2s + 2 = 0 Using the Routh-Hurwitz method, check
At t=0, a 1 pound force, denoted by f(t), is applied to the translational mechanical system. Determine K and M such that the response has a 1 second peak time and 4 second settling time if fv = 1. Additionally, what is the resulting overshoot percentage? Determine also the resulting transfer function as well as the steady state error for step input.
Enter the value of the K coefficient required for the marginally stable/unstable system of a system whose characteristic equation is given as s3+6s2+3s+K=0.
Transfer function of the pulmonary system that represents alveolar pressure PA to Pao is given by H(s)=(0.8∗8,5)/(s^2+4s+8,5) . for Pao = 5 mmH2O, PA at steady-state is …… mmH2O
Select the forward path gain (M ktop) for the system for the SFG diagram given below
G(s)=((s+1)*(s+15))/((s+0.1)*(s+2.5)*(s+120)*(s+240)) 1-draw nyquist 2- Nyquist criterion, compute the number of unstable poles of the closed loop system as a function of K 3-determine for which values of K the closed system is stable.
For the circuit shown below, determine:a)The expression of the input current of the circuit in the time and frequency domain, respectively, i(t) and I(s).b)The circuit impedance, Z(s) = V(s)/I(s).c)The stress expression, v(t).d)The currents in the resistor, iR(t), and in the capacitor, iC(t).e)Repeat items c and d if v(0) = – 5 V.
By plotting the root locus of the system given as the open loop function : G(s)= K/(s*(s+2)); a) When K=4, show the locations of the closed loop poles on the root locus. Determine the Damping Ratio and Natural Frequency values in this gain value. b) Calculate the unit step response of this closed-loop system by calculating the Percent Overshoot, Peak, and Settlement Time values and plot them to scale. c) Scan the region on the root locus where the pairs of conjugate poles must be in order for this inspected system to work at least in the success criteria (greater than the calculated damping rate and natural frequency) in (a).
For the circuit shown below, the initial conditions are zero, Idc is a current source continuous and switch S is open at t = 0.a)Determine the equivalent impedance to the right of points a and b of the circuit, Z(s).b)Obtain the voltage between points a and b of the circuit in the frequency domain, V(s). Employ the initial and final value properties and calculate the values of v(0) and v(∞).c)Find the expression for v(t). Check that the values of v(0) and v(∞) agree with those calculated in the previous item.d)Obtain currents i1(t) and i2(t).
The structural engineering design section within the engineering department of a regional electrical utility corporation has developed several standard designs for a group of similar transmission line towers. The detailed design for each tower is based on one of the standard designs. A transmission line project involving 50 towers has been approved. The estimated number of engineering hours needed to accomplish the first detailed tower design is 126. Assuming a 95% learning curve, a. What is your estimate of the number of engineering hours needed to design the eighth tower and to design the last tower in the project? b. What is your estimate of the cumulative average hours required for the first five designs?