EX2: (Buck dc-dc converter. Evaluation of the output voltage ripple) A buck converter has the following specifications: Vin= dc input voltage =50 V, D = duty cycle=D0.4, L=400 µH, C=100 µF f,= switching frequency = 20 kHz, R=20 2 Assuming that the converter is ideal, calculate: a) The output voltage. b) The maximum and minimum inductor current values. c) The output voltage ripple.

EX2: (Buck dc-dc converter. Evaluation of the output voltage ripple) A buck converter has the following specifications: Vin= dc input voltage =50 V, D = duty cycle=D0.4, L=400 µH, C=100 µF f,= switching frequency = 20 kHz, R=20 2 Assuming that the converter is ideal, calculate: a) The output voltage. b) The maximum and minimum inductor current values. c) The output voltage ripple.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Discuss the principle and working of the thermionic converter with a neat diagram.
For the dc-dc converter (operating in CCM) depicted in the figure below, make all the required assumptionsand find the input-output voltage ratio (Vo/Vin = ?).
plot the theoretical and practical control characteristics of the Buck converter, and comments on your the obtained curve.
Drive the expression for the average output voltage of a single phase full converter and draw the waveform of output voltage. please explain in details
the Advantages DC-TO-DC Converter.
Industrial Electronics If the given types of DC-DC Converter has an input voltage of 25V. The output voltage of each converter using a duty cycle of 0.4s. a.) Buck Converter Vout?b.) Boost Converter Vout?C.)Buck-boost converter Vout?
For a single-phase Ac-Ac Converter with unidirictional phase control, find the output dc voltage, where, the delay angle is 0 degree, the input voltage is 120sinwt with 10ohm resistive load consider
The circuit diagram of step-up type DC-DC converter is given below. It is assumed that the output capacitor is large enough and the output voltage is constant. (Consider that there is no circuit losses.) What should the inductance value be for the circuit to always operate in Continuous Current Mode (CCM)? Calculate.
3) Explain the construction, principle of operation, circuit and applications of Variable reluctance transducer with neat diagrams. 4) Describe the construction of LVDT and explain its principle of operation with the aid of diagram, list the advantages, disadvantages and applications of LVDT.
Describing the concept of discontinuous conduction mode in power converters, how does continuous conduction mode differ?Make a DC-DC converter circuit that operates in discontinuous conduction mode.
A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is 33 V
amplifier (boost) DC-DA converter circuit, given below; 1- Source voltage (E) value: In the voltage range of [A B] (Volts) 2- Switching frequency (f) value: M kHz 3- Voltage between load terminals (Vload) F (volt) 4- Capacity value is 470 (microF) 5- Pload>= H(watts) consumed per load In which case below do you see the lowest L inductance value in microH that can keep the DC-DC converter in a continuous current state under the conditions? A=25 VOLT B=40 VOLT M= 25kHz F = 55 VOLT H=15 Watts a) 454.5475 b) 382,045 c) 263.62 d) 128.5 e) 581.81