i need the answer quickly Examining and modifying the contents of the 8086's internal registers1. Use the REGISTER command to display the current contents of all the internal registers bytyping R.o List the values of the following registers:BXDXIPSPCSSSo What is the address of the next instruction to be executed?2. Enter the command: R AH (hit ) What happens and why?3. Use a REGISTER command to first display the current contents of BX and then change thisvalue to 0020h.

Answered: Image /qna-images/answer/9955a2dc-2db0-4fa8-ac87-fb5285d25e0f.jpg

Examining and modifying the contents of the 8086's internal registers 1. Use the REGISTER command to display the current contents of all the internal registers by typing R. o List the values of the following registers: BN DX IP o What is the address of the next instruction to be executed? 2. Enter the command: R AH (hit ) What happens and why? 3. Use a REGISTER command to first display the current contents of BX and then change this value to 0020h.

Examining and modifying the contents of the 8086's internal registers 1. Use the REGISTER command to display the current contents of all the internal registers by typing R. o List the values of the following registers: BN DX IP o What is the address of the next instruction to be executed? 2. Enter the command: R AH (hit ) What happens and why? 3. Use a REGISTER command to first display the current contents of BX and then change this value to 0020h.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Change your Virtual Memory pagefile to the following capacity: Initial Size: 10MBMaximum size: 250MBNB: Do not apply your changes. (9)Instructions:- Provide all necessary steps to accomplishing the tasks above.- Upon successful completion, provide screenshots of your created Virtual Memory pagefile.
Rearrange the steps for X86 interrupt processing: a. Save current processor status word (condition codes) b. Switch to kernel mode c. Interrupt handler saves registers it might clobber d. Save current program counter e. Switch to kernel stack; put SP, PC, PSW on stack f. Vector through interrupt table g. Save current stack pointer
3 Suppose, you need to service 48 hardware interrupts on your 8086microprocessor. Explain how many 8259 (PIC) chips you’d need to service the above number ofinterrupts. Further, explain why only a total of 64 interrupts can be serviced with the help ofcascading.
Instruction: Analyze the given Emu8086 assembly codes and answer the following questions. Note: You can execute the program if you have the Emu8086 Emulator installed on your computer. What is the purpose of Lines 39-40? What is the purpose of Lines 49-50? What is the purpose of the next: section in the program?
What do you call the logic that determines what data is most needed in the future and should be stored in the CPU’s cache? interrupt caching discombobulate logic replacement policy virtual memory
What is the purpose of RAM's "zero page"? A. It is connected to all the System Board slots. Programs can write/read to those addresses. B. It is an unused part of RAM C. The operating system stores its I/O libraries at that location D. It identifies all the addresses in RAM that have many leading zero bits.Which of the following is true about a chipset? There might be more than one correct answer. A. It is a group of chips (machines) that cooperate together on a common purpose. B. The chips (machines) on a controller card are also considered to be chipsets. C. The MIPS CPU Chipset consists of the Integer CPU, the Floating-point co-processor, and the Interrupt (or Error) co-processor. All these devices can also connect with RAM. D. The MIPS CPU Chipset consists of the Integer CPU, the Floating-point co-processor, and the Interrupt (or Error) co-processor. Only the Integer CPU and the Floating-point co-processor can connect to RAM.
23. How can the processor ignore other interrupts when it is servicing one a. By turning off the interrupt request line b. By disabling the devices from sending the interrupts c. By using edge-triggered request lines d. All of the above
1. Create a program using the ARMv7 instruction set to do the following: o Read a single pushbutton o Output a 0 on a seven segment display when the button is pushed in o Output a 1 on a seven segment display when the button is not pushed 2. Create a program using the 8086 instruction set to do the following: o Read 2 single digit numbers from keystrokes of the keyboard using interrupts o Add the two single digit numbers o Display the numbers using interrupts
Computer Organization and ArchitectureAssignment Submit your work by uploading it in Blackboard or bringing it as a hard copy to my office by the deadline. Answer the following question:1-What is the datapath?2-What is the Instruction cycle?3-What is the memory hierarchy? 4-Give small description or example and indicate the format of the following MIPS functions:(The first two of them are examples) Please here is three columns one to instructions and two to format of instruction and three column is to description of function to all instructions but i don't copy to here only Please solve it. FormatFormatDescription lw $1,100($2)Iload word from $2+100 and put it in $1 and $1,$2,$3Gadd $2 and $3 and put the result in $1 | $1= $2+$3 Sw $1,100($2) la $1,label andi $1,$2,100 or $1,$2,100 srl $1,$2,10 li $1,100 move $1,$2 Beq $1,$2,100 Bne $1,$2,100 div $2,$3 Bgt $1,$2,100 addi $1,$2,100 addu $1,$2,$3
Assume the PC has the address 0x021A when FETCH INSTRUCTION phase begins. After that first instruction executes, which one describes the second instruction to execute? a) LDR R4 with a value from memory b) LDR R5 with a value from memory c) ADD R4 to R5 and save result in R7 d)
Microprocessor 8086 Code Mov 0058H ,04H Mov 0053H,06H So when I calculate physical address in formula Ds*10+offset address I get my Ds indicates 3000 So 3000*10+0058=30058 physical address When try to find 30058 in the memory location in emu8086 I couldn’t find this physical address in the memory but I see another address is that I am wrong in this way What want to do is When go to 30058 physical address in this address to value of 04H on its data a m wrong?
using the tasm syntax (intel style), write a x86 assembly code that does the following tasks: (a) add two groups of numbers using the loop instruction, 1 + 3 + 5 + ... + 99 2 + 4 + 6 + ... + 100 (b) print the two results on the screen. (c) the code must be assembled/built/run successfully with the gui_tasm software