i need the answer quickly Equivalent noise temperature2G.F)TeNa%3D%3DKKBandlimited white noiseG) df = NaB = KtBP =%3D%3DThe power spectral density at the input and output can be found asGyf) = |H(f)l²x(f)And the autocorrelation for the noisy output isRy (T) = | |H(F)|²x(f)e}2nft dfx-The average power of the output signal is< y? >= R,(0) = [*,IH()P*x(f)dfExample 1:Calculate the RMS and the available power at the thermal noise in 100 2 at 27 C° and 6MH:bandwidth.

It is given that: R=100ΩT=27°CB=6MHz

Answered: Example 1: Calculate the RMS and the…

Engineering

Electrical Engineering

Example 1: Calculate the RMS and the available power at the thermal noise in 100 2 at 27 C° and 6MH: bandwidth.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Show that the derivative of a 1-D signal, I=I(x), amplifies the higher frequency components of the signal. Then, prove that even a slight amount of noise n=n(x), can be responsible for a large difference between the derivative I and I+n (Hint: Assume that n can be written as εsin(ωx) for some very small ε and very large ω).
Obtaining broadband FM signal from narrowband frequency modulated (FM) signal is shown below. The narrowband FM signal has a maximum frequency deviation of 100 Hz. The frequency of the local oscillator is f0=100 kHz. Since the sign at point A is Ac(cos 2πf0t+θ(t)), express the signs at points B and C. Ac is a constant and θ(t) is a function of m(t).
For the system defined by the first-order differential equation 100y'(t) + y(t) = x(t). a) Plot the log magnitude (dB)-log frequency graph of H(jw). b) The input is assumed to be suppressed when the magnitude of H(jw) is -40 dB. It is given that the x(t)=coswat signal is suppressed by this system. What is the smallest wa value in this case? Subject: Signals and Systems
100 y(t)+ y (t) = X(t) for a system defined by a first-order differential equation:a. Draw the log magnitude(dB)-log frequency graph of H (jw) (phase graph is not requested. it is expected that the frequency axis will also be logarithmic when plotting the log magnitude graph).b. If the magnitude of H(jw) is -40 dB, it is assumed that the input is suppressed. it is given that the signal X (t) = coswat is suppressed by this system. What is the smallest wa value in this case?
An FM signal, eFM = 50 sin [2π(800k)t - 4 sin 2π(5k)t] is produced by a frequency modulator with -500Hz/V frequency deviation constant. Determine (a)Determine the equation of the carrier signal (b) What is the equation of the modulating signal (c) Determine the approximate bandwidth of the FM signal (use Carson’s Approximation)
1. The CT signal x(t)=3cos (600πt) + 6cos2 (mπt) is critically sampled (Nyquist rate)by fs=4000 Hz. Find:i. The value of m.ii. The frequency components of the signal.iii. The frequency resolution (Δf) of the output spectrum if the sampled signal isprocessed by 64 point-DFT.iv. Define frequency resolution.
It is given that F(ω)=eωu(-ω)+e-ωu(?). 1. Find f(t). 2. Find the 1 Ω energy associated with f(t) via time-domainintegration. 3. Repeat (b) using frequency-domain integration. 4. Find the value of ω1 if f(t) has 90% of the energy in the frequencyband 0≤| ω |≤ω1.
A continuous time signal, x(t) = sin(20πt) + cos(40πt), is sampled uniformly at intervals of T to obtaina discrete time signal,x(n) = sin(πn/5) + cos(2πn/5).a) What is the value of T assuming no aliasing has occurred?b) Assume both frequency components have been aliased. In this case, is your choice of T unique? If not,specify some choices of T consistent with the information given
Let's consider a communication system where four signals with different frequencies (f1,f2,f3 and f4) are combined to form a composite signal. The composite signal is represented by the equation:
4. A single sideband signal is derived from a sinusoidal carrier of 100kHz and audiofrequencies between 6kHz and 10kHz. In this situation, the upper sideband wouldextend from:a 106kHz to 110kHzb 210kHz to 216kHzc 90kHz to 94kHzd 6kHz to 10kHz 5. A BFO:a extracts the lower sideband from a DSB transmission.b generates a signal that is exactly twice the frequency of the system carrier wave.c generates a sinewave of constant frequency.d allows FM signals to be demodulated on an AM broadcast receiver
In case the sound from the engine of a vehicle is modelled by the function y(t) = cos[ω(t + τ) + θ] where time delay=τ & phase=θ Determine the frequency & period of the signal u(t) whena)[ω, τ, θ] = [π/3, 1/2, π/2]b)[ω, τ, θ] = [3π/4, 1/2, π/4] N.b time should be in seconds & frequency in Hertz. c) y(t) = e-atu(t) for t≥0 & y(t) = 0 for t<0 where a>0 is a constant The function above defines the model of the decay of the vibration of a vehicle engine. i.Make a sketch of the signal y(t) & determime its fourier transform.
a. In an RC circuit supplied with AC power, a 500 ohm resistor is used to create a system with a crossover frequency wc =440 rad/s. What capacitance is the capacitor in this circuit? b. If an inductor is to be added to this circuit to make the resonant frequency equal to the crossover frequency, then what inductance must this inductor have? c. If, near a particular time t1, the instantaneous voltage drop over the resistor is given by v(t1)=0.65V cos(440t), then what is i(t1) (the function of instantaneous current with respect to time) for its capacitor? d. What would the Irms value be based on the sinusoidal function you found in part c? (Pick off Ipeak from the function, then plug in to rms equation) Since this is multi-part, answers to later parts will be graded based on your answers to previous parts when necessary.