Example 1.6 Around bar as shown in Fig-1- is subjected to an axial tensile load Of 100KN. what must be the diameter(d) if the stress there is to be 100MN/m ? Find also the total elongation. E=200Gpa. 100KN 10cm 100KN Fig-1- ocm- -15cm- -15cm-

Example 1.6 Around bar as shown in Fig-1- is subjected to an axial tensile load Of 100KN. what must be the diameter(d) if the stress there is to be 100MN/m ? Find also the total elongation. E=200Gpa. 100KN 10cm 100KN Fig-1- ocm- -15cm- -15cm-

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.17P: A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at...

See similar textbooks

Related questions

Q: A 12mm thick steel tire has a width of 110mm and has an internal diameter of 800mm. The tire is…

Q: For fig shown if water flow rate is 60 lit/s, Find (h) Note that Density: Pwater = 1 kg/m Pair = 1…

Q: To measure the density of a stone, a digital scale and a beaker cup filled with water are used. The…

A: The density of material shows the thickness of that material in a particular given region. A…

Q: Determine the (f_y when force 80 Ib and angle 30° on the axis (X)

Q: A hot rolled steel tension test sample has a diameter of 6 mm and the original gage lenght of 30 mm.…

A: Original diameter of the specimen, Do=6mm Original Length of the specimen, Lo=30mm Fracture…

Q: 880mm Double shear T= 130MP. В A 720mm 260mm CO Bar 2 OE E = 105 GPa A = 375 mm2 400mm 430mm Bar 1 D…

A: The diameter of the pin B can be easily calculated by using the formula given below as- τs=FrAc…

Q: For a cantilever beam subjected to a vertical force at its free end, how many elements should be…

A: Draw the free-body diagram of a cantilever beam subjected to a vertical force at its free end.

Q: Draw the shear and moment diagram of the beams shown below. 120 kN/m A.) A 1 m 7 m 200 kN

Q: Q2A = 2 inches, AB = 14 inches and AC = 2 inches. If slide 6 has an instantaneous velocity of 1 fps…

Q: 3. Calculate a circular pressure tank volume and its uncertainty if the diameter, D, is 1.5 m and…

Q: 10 .In a certain refrigeration system for low temperature application , a two- stage operation is…

Q: 4. A uniform 45-kg beam is held in a vertical position by a pin at its lower end and a cable at its…

A: The total reaction force at the pin can be calculated using the 3 equations of statics which are-…

Q: 1. Using superposition of loads, create a single V and M function if a positive bending moment of…

A: Bending MomentThe logarithmic amount of everything minutes following up on the construction is known…

Q: A triangular lamina is immersed vertically in water in such a way that its 6 m wide horizontal base…

Q: The roof of a house consists of a 0.70-ft-thick concrete slab (k = 3 W/m · °C) that is 18 m wide and…

Q: 5.1 through 5.15 Calculate the forces in all members of the trusses shown using the method of…

A: Find the force in each members.

Q: What mass of water can be heated from 25.0° C to 50.0° C by the addition of 2825 J? * O 27 gm O 22…

A: Find the mass of water .

Q: An ideal regenerative cycle is executed with steam generation at 10000KPa and 873 Kelvin. Before…

Q: Qu Coolives and adiabitic Huunidifiction by water ijeblon Celacityof couling aile OBT, ac Gilecde…

Q: Market share in Deposits of all banks in 2020 sON 15% 10% 25% Q 26. Find the ratio of the market…

A: Using simple mathematics calculation

Q: Hand Boiler Mechanics

A: A hand boiler is a glass toy filled with ethyl alcohol. The boiler is made out of a twisting…

Q: Derive the kinetic energy equations and the mass equivalents of the two-system shown. -Thin disk of…

Q: (A) Compute the compression ratio of an engine that has a bore of 5 in. and a stroke of 5 in. when…

Q: 1. Determine the force in each member of the truss, and state if the members are in tension or…

Q: nsidering the various failure cases of the join parts to determine the minimi its of the mechanical…

Q: Who invented the hand boiler

A: A hand boiler is a glass toy filled with ethyl alcohol. The boiler is made out of a twisting…

Q: In the system of reservoirs shown below, the flow of Reservoir 1 to Reservoir 2 is Q=15 cfs. At…

A: Consider the given data

Q: Home Work: 1. Draw shear force and bending moment diagrams for the beam shown in figure. 30kN 2m…

Q: 1.0 kN.m 6 kN H Ki 220 mm Q3 Q3. A 6-kN force and a 1.0kNm couple are applied at the top of the…

Q: The motorcycle has a kerb mass of 239 kg and test rider's mass was recorded as 76.35 kg. The wheels…

Q: In an undisturbed sea level condition airstream, the velocity of the flow is 600 ft/s. What is the…

Q: Calculate the reservoir volume filtered in an affinity absorption system plasma filtrate flows…

A: Given Diameter, d = 0. 5mm Velocity, u = 2 mL/min Volume, V = 0.02 mg/mL Find Volume…

Q: ᴀ ꜱᴛᴇᴇʟ ʜᴀꜱ ᴀ ʙʜɴ = 500. ᴡʜᴀᴛ ɪꜱ ɪᴛꜱ ᴀᴘᴘʀᴏxɪᴍᴀᴛᴇ ᴜʟᴛɪᴍᴀᴛᴇ ꜱᴛʀᴇɴɢᴛʜ ɪɴ ᴍᴘᴀ? a.250000 b. 2225 c.1725…

Q: Part A It takes a vertical force of F = 45,000 lb to separate the two parts at A and C in (Eigure…

Q: In a certain refrigeration system for low temperature application , a two- stage operation is…

Q: (Determine the (f_x ) when force 90 N and angle 50° on the axis (Y .A 68N .B 68.94lb .C 69N .D…

Q: A company is feeling adventurous and is expanding into a new market with a new product. They are…

Q: Response of the two-degree-0 0.915 and uz = 2.0 is such that q2 = 0. Find the mode shapes and a,…

A: INTRODUCTION : The response of two degree of freedom system means that, the system required two…

Q: PROBLEM 2.33 An axial force of 60 kN is applied to the assembly shown by means of rigid end plates.…

Q: In an ammonia refrigerator , the pressure in the evaporator is 267. 58 KPa and the ammonia at is…

A: Dear student, in this question only volume of vapor entering the compressor is asked. So there is no…

Q: Convert heat conduction from cylindrical coordinate to Cartesian coordinate?

Q: A triangular lamina is immersed vertically in water in such a way that its 6 m wide horizontal base…

Q: 1. Determine the force in each member of the truss, and state if the members are in tension or…

Q: (Problem 6.32 from the text book) Several wooden planks are glued together to form the box beam…

A: Given: vertical shear, V = 3 kN To find: Average shear stress: (a)at A (b)at B

Q: A fracture surface of a metal matrix composite (nickel with silicon carbide fibres) is investigated…

A: When light is used we can not see anything smaller than the wavelength of light and therefore…

Q: A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37.5mm left…

A: Answer: (a) The axial load at Q is 225 kN. (b) The stress induced at point C is 0.9167 MPa (Tension)…

Q: 1. volume flow rate of Benzene. 2. Mass flow rate of Benzene. 3. Weight flow rate of Benzene

Q: Calculate the reservoir volume filtered in an affinity absorption system plasma filtrate flows…

A: Given Diameter, d = 0. 5mm Velocity, u = 2 mL/min Volume, V = 0.02 mg/mL Find Volume…

Q: In an air-conditioning unit 3.5 m3/s air at 27°C dry-bulb temperature, 21°C wet-bulb temperature,…

Q: The mass of a solid hemisphere is measured once with a digital balance whose resolution is 1 g. The…

Concept explainers

Terminology in Metal Alloys

Metal is the pure chemical element you would find on the periodic table. 91 of the 118 elements on the periodic table are metals – which make them some of the most plentiful elements in the world.

Question

Please solve quickly Resist materials

Example 1.6
Around bar as shown in Fig-1- is subjected to an axial tensile load
Of 100KN. what must be the diameter(d) if the stress there is to be
100MN/m ? Find also the total elongation. E=200Gpa.
100KN
10cm
Ecm
100KN
Fig-1-
ocm-
-15cm-
-15 cm-

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.
An aluminum tube is required to transmit an axial tensile force P = 33 k (sec figure part a). The thickness of the wall of the tube is 0.25 in. (a) What is the minimum required outer diameter d minif the allowable tensile stress is 12.000 psi? (b) Repeat part (a) if the tube has a hole of a diameter J/10 at mid-length (see figure parts b and C).
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A bar of monel metal with a length L = 9 in. and a diameter d = 0225 in. is loaded axially by a tensile force P (see figure). If the bar elongates by 0.0)95 in., what is the decrease in diameter
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A high-strength steel bar used in a large crane has a diameter d = 2.00 in. (sec figure). The steel has a modulus of elasticity E = 29 × 10 psi and Poisson’s ratio is v = 0.29. Because of clearance requirements, the diameter of the bar is limited to 2.001 in. when it is compressed by axial forces. What is the largest compressive load Pmaxthat is permitted?
A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The hole may have any diameter that will fit within the bar. What is the maximum permissible tensile load Pmaxif the allowable tensile stress in the material is st?
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.