Example 6 1-38: Link BC is 6 mm thick, has a width w = with a 480 MPa ultimate strength in tension. What was the safety factor used if the structure shown was designed to support a 16 kN load P? 25 mm, and is made of a steel 600 mm W. 90° 480 mm

Example 6 1-38: Link BC is 6 mm thick, has a width w = with a 480 MPa ultimate strength in tension. What was the safety factor used if the structure shown was designed to support a 16 kN load P? 25 mm, and is made of a steel 600 mm W. 90° 480 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.5P: A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure)....

See similar textbooks

Related questions

Q: Problem 1 of 2: Nodal displacements for the elements 1-3 and 2-3 of a plane truss were determined to…

A: Given dataDisplacements of points in x and y directionsu1 = 1.5mmu2 = 0.2mmu3 = -2.7mmv1 = 3.1mmv2…

Q: Figure Q2 shows a rigid link supported by a pin at C and two A-36 steel wires. Each wire having an…

Q: a. Two brass rods used as compression members, each of 3-m effective length with pin end, have the…

A: Given:Effective length of the rods, Le=3 mOuter diameter of circle, do=60mmInner diameter of circle,…

Q: Both ends of the fixed (fixed) rod were mounted at 0 °C. Calculate the minimum diameter of the bar…

Q: "Prob. 10.3-5. A square, tubular steel column has the di- mensions shown in Fig. P10.3.5, has a…

A: Given:L=3 mP=50 KNEst=210GPaσy=250MPaa=150mmb=125mm

Q: The metallic hollow pipe shown in Figure Q2 is fixed at its lower end and free at its top end, and…

Q: Required information The cantilevered bar in the figure is made from a ductile material and is…

A: The cantilever beam static load given as, Fy= 380 lbf The diameter of the beam is given as, D= 3 in…

Q: A link is shown in the figure. If the allowable combined stress at a-a is limited to 30 ksi, what is…

A: GivenσA=30ksi

Q: The frame shown in the provide figure has Load F applied at point D. Answer the following questions…

A: Given: The applied force F is 600 N.

Q: Problem 3. The tension lock shown at the figure below will be loaded by an axial force F = 10 kN.…

Q: 2.10-3 A flat bar of width b and thickness 1 has a hole of diameter d drilled through it (see…

A: Given data: - The width of the bar is b. The thickness of the bar is t. The diameter of the hole…

Q: An aluminum bar having a cross-sectional area of 0.5 in? carries the axial loads applied at the…

A: Given Data Area, A=0.5 in2. E=10(106) psi

Q: A column has pinned ends and is axially loaded in compression. The length is 6 m and the weight is…

Q: 3) Figure - 3 illustrates a type of engineering chain used for conveying applications. All…

Q: 2. A square hollow steel strut with a wall thickness, t, = 10 mm is pin connected to two gusset…

Q: • Q-2 Figure gives the cross section of a grade 25 cast-iron pressure vessel. A total of N bolts are…

A: Given: No:25 CI M16×20×60mm class 5.8 H=14.8mm…

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

Q: s): The butt connection shown below is fastened by 20-mm diameter bolts. Find the maximum allowable…

A: given; diameter (d)=20mmload(P)=?bearing stress(σb)=160MPatensile stess(σt)=80MPashearing…

Q: The figure shows truss. It is supported with a pin at A and a roller at B. There are three pointed…

A: (a) Draw the free-body diagram of the truss.

Q: P 5 kN 150 mm 300mm 70° B 10 mm- в 6 mm

A: Given, σy-B = 60 MPaσy-CD = 100 MPaSF = 2t = 6 mm Consider below FBD for the given question:

Q: Q.3. The right-angle bar shown in figure (3) is supported by a pin at B and a roller at C. What is…

Q: A butt connection is shown in the following figure. Plates is Q235 steel; 8.8 Grade M16 high-…

A: Load bearing capacity Loadbearing capacity is the maximum ability of a structural member or…

Q: how many times is the system safe

A: For solution refer below images.

Q: The steel bar in the figure has a hollow circular cross-section (dais = 111 mm, tooth = 85 mm), one…

A: The expression for the buckling load, one side hinged and one side is shown below.

Q: The pinned truss in Fig Q2 is subject to a vertical load of 120kN at Pin C. The strut members AB, BC…

Q: Question 2) In the system given in the figure, a distributed load of w = 88 kN /m affects the AB rcd…

A: Given: load w= 88 kN/m; AB=4.1m; θ=56°; a=28mm;σm=212 MPa; ζm=70 MPa To Find: b? pin diameter at B

Q: Circular steel bars will be used in the cage system in the figure. Accordingly, find the safety and…

A: The roller at D gives the vertical reaction and the hinge at G gives the horizontal and vertical…

Q: Q2/ A bracket as shown in figure (Q2), is fitted to a wall with 5 bolts (M16× 1.5), three at the top…

Q: 1.8-4 The inclined ladder AB supports a house painter (85 kg) at C and the weight (q = 40 N/m) of…

Q: Problem Rigid bar ABCD is initially horizontal before the load W is applied and a change of…

Q: A rigid bar of weight W- 810 N hangs frem three equally spaced vertical wires (length L-150 mm,…

A: FBD of rigid bar Area of Aluminium wireAA=π4dA2=π442=12.5664mm2Area of steel wire…

Q: Q-1 A solid circular rod with a diameter d= 18 mm is shown in Figure Q-3. The rod is made of an…

Q: ,5-16 A rigid bar ABCD is pinned at end A and supported by two cables at points Band C. The cables…

Q: A pin in a knuckle joint carrying a tensile load Fdeflects somewhat on account of this loading,…

Q: The bell crack mechanism shown in Figure is in equilibrium for an applied load of F1 - 15KN at A and…

A: Answer: The magnitude of the resultant reaction force acting at point B is 30.5 kN.

Q: "Prob. 10.3-5. A square, tubular steel column has the d mensions shown in Fig. P10.3.5, has a length…

A: given:axial compression load P=50KNlength L=3mEst=210GPa σy=250MPa

Q: The cantilevered bar in the figure is made from a ductile material and is statically loaded with Fy…

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. P-211. Axial loads…

A: Given that: For the composite bar maximum allowable horizontal deformation is 3 mm. It is required…

Q: required using tresca iheory ww w of (2).

A: Step 1 Resolve the force into vertical and horizontal component Step-2 Calculate net moment acting…

Q: Problem # 4: Three links are used to support load P = 10.25 kips. Disregarding any defomation for…

Q: Problem 209 An aluminum bar having a cross-sectional area of 0.5 in? carries the axial loads applied…

A: P1= 6000 lb Tension P2= 1000 lb Compression P3= 4000 lb Tension

Q: The steel bar has the original dimensions shown in the figure with b = 350 mm and c = 222 mm. If it…

A: It is given that

Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R, and R₂. The…

A: Given data: ● The load applied on the beam: W = 13 kN ● The diameter of the beam: d = 25 mm ● The…

Q: A rectangular filleted bar as shown in figure below is subjected to a fluctuating force F that…

A: The Answer is below

Q: Question 3 An aluminum tube AB of circular secton has a fixed support at the base and is pinned at…

A: Apply moment equilibrium condition.

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A: (a) Draw a free-body diagram of the beam.

Q: 3. A square aluminum bar is to support a load of 40 kN on a length of 3 m. Assuming pinned ends,…

Q: , S-16 A rigid bar ABCD is pinned at end A and supported by two cables at points B and C(see…

A: Stress produces in the material due to changes in temperature is known as thermal stress. Condition…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

Example 6
1-38: Link BC is 6 mm thick, has a width w = 25 mm, and is made of a steel
with a 480 MPa ultimate strength in tension. What was the safety factor used if
the structure shown was designed to support a 16 kN load P?
600 mm
A
W.
90°
480 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness ßRat A. Determine the critical load Pcr for the structure.
The figure shows an idealized structure consisting of two rigid bars joined by an elastic connection with rotational stiffness ßR. Determine the critical load PCTfor the structure.
A pinned-end strut of aluminum (E = 10,400 ksi) with a length L = 6 ft is constructed of circular tubing with an outside diameter d = 1 in. (sec figure). The strut must resist an axial load F = 4 kips with a factor of safety n = 2.0 with respect to the critical load. Determine the required thickness t of the tube.
An aluminum pipe column (E = 10,400 ksi) with a length L = 10.0 ft has inside and outside diameters d1= 5.0 in. and d2= 6.0 in., respectively (sec figure). The column is supported only at the ends and may buckle in any direction. Calculate the critical load Pcrfor the following end conditions: (a) pinned-pinned, (b) fixed-free, (c) fixed-pinned, and (d) fixed-fixed.
An idealized column is made up of rigid bars ABC and CD that are joined by a rotational elastic connection at C with stiffness ßR. The column has a roller support at B and a pin support at D. Find an expression for the critical load Pcr of the column.
A cantilever aluminum column has a square tube cross section with an outer dimension of 150 mm. The column has a length L = 4 m and is designed to support an axial load of 45 kN. Find the minimum required thickness of the section if the factor of safety n = 2.5 with respect to buckling. Assume that the modulus of elasticity is 72 GPa and the proportional limit is 480 MPa.
A fixed-end column with circular cross section is acted on by compressive axial load P. The IS-ft-long-column has an outer diameter of 5 in., a thickness of 0.5 in., and is made of aluminum with a modulus of elasticity of 10,000 ksi. Find the buckling load of the column.
A fixed-pinned column is a W310 × 21 steel shape and is designed to carry an axial load of 125 kN. Determine the maximum permissible height L of the column if a factor of safety n = 2.5 is required with respect to the buckling of the column. Use E = 205 GPa and assume that the proportional limit is 340 MPa. The column may buckle about either axis of the cross section.
An aluminum tube AB with a circular cross section has a sliding support at the base and is pinned at the top to a horizontal beam supporting a load Q = 200 kN (sec figure). Determine the required thickness t of the tube if its outside diameter d is 200 mm and the desired factor of safety with respect to Eu 1er buckling is n = 3.0. (Assume E = 72 GPa.)
A steel pipe column with pinned ends supports an axial load P = 21 kips. The pipe has outside and inside diameters of 3.5 in. and 2.9 in., respectively. What is the maximum permissible length Lmaxof the column if E = 29,000 ksi and y = 36 ksi?
A slender bar AB with pinned ends and length L is held between immovable supports (see figure). What increase T in the temperature of the bar will produce buckling at the Eu1er load?
A wide-flange steel column (E = 30 × l06 psi) of W12 × 87 shape (see figure) h as a length L = 28 ft. It is supported only at the ends and may buckle in any direction. Calculate the allowable load Pallowbased upon the critical load with a factor of safety n = 2.5. Consider the following end conditions: (a) pinned-pinned, (b) fixed-free, (c) fixed-pinned, and (d) fixed-fixed.