ExampleThe beam ABC is loaded via a 500 N.m couple and a 600 N force as shown. Thebeam is connected to the rest of the system by a pin joint at B and a roller support atC. Detemine the magnitude of the reaction forces on the beam at the supports.600 N500 N.m400300500Ans.RC=1700 NRBx=1597.5NDimensions in mmREDMI NOTE 9 PROAI QUAD CAMERARBy=1181.4 N

Answered: Image /qna-images/answer/fae71c35-4d69-4e03-ad61-78a273dce77c.jpg

Example The beam ABC is loaded via a 500 N.m couple and a 600 N force as shown. The beam is connected to the rest of the system by a pin joint at B and a roller support at C. Determine the magnitude of the reaction forces on the beam at the supports. 600 N 500 N.m 400 300 500 Ans. Dimensions in mm RC=1700 N

Example The beam ABC is loaded via a 500 N.m couple and a 600 N force as shown. The beam is connected to the rest of the system by a pin joint at B and a roller support at C. Determine the magnitude of the reaction forces on the beam at the supports. 600 N 500 N.m 400 300 500 Ans. Dimensions in mm RC=1700 N

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.12.12P: A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the...

See similar textbooks

Similar questions

‘11.5-2 A steel bar having a square cross section (50 mm × 50 mm)and length L = 2.0 in is compressed by axial loads that have a resultant P = 60 kN acting at the midpoint of one side of the cross section (sec figure). Assuming that the modulus of elasticity £is equal to 210 GPa and that the ends of the bar are pinned, calculate the maximum deflection S and the maximum bending moment Mmax.
An S6 × 12.5 steel cantilever beam AB is supported by a steel tic rod at B as shown. The tie rod is just taut when a roller support is added at Cat a distance s to the left of £, then the distributed load q is applied to beam segment AC, Assume E = 30 × 106 psi and neglect the self-weight of the beam and tie rod. Sec Table F-2(a) in Appendix F for the properties of the S-shape beam. (a) What value of uniform load q will, if exceeded, result in buckling of the tie rod if L1, =6 ft, s = 2 ft, H = 3 ft, and d = 0.25 in.? (b) What minimum beam moment of inertia ibis required to prevent buckling of the tie rod if q = 200 lb/ft, L1, = 6 ft, H = 3 ft, d = 0.25 in., and s = 2 ft? (c) For what distance s will the tic rod be just on the verge of buckling if q = 200 lb/ft, L1= 6 ft, M = 3 ft, and d = 0.25 in.?
(use EI constant for whole span). A 10-meter-span, propped beam (fixed at the left support and roller at right support), with a uniformly distributed load from left support to six meters to the right, with a magnitude of six kilonewton per lineal meter, a downward concentrated load at the midspan. Solve the reactions at the fixed support and roller support, slope and deflection at the roller support, using Area Moment Method. Use the concentrated load as 24 kN.
Draw the influence lines for the vertical reactions at supports A and E and the reaction moment at support E of the beam shown in Fig. P8.13.
A simply supported beam of length L has a concentrated couple Mo of 10 kN-m applied at one end of the beam. Use E = 200 GPa and I = 60 000 000 mm^4. If L = 7 meters Which of the ff. most nearly gives the maximum deflection from the applied load in mm.
A beam ABCDE is simply supported at A and D. It carries the following loading: a distributed load of 30 kN/m between A and B; a concentrated load of 20 kN at B; a concentrated load of 20 kN at C; a concentrated load of 10 kN at E; a distributed load of 60 kN/m between D and E. Span AB=1.5 m BC=CD=DE=1 m. A. Draw the FBD B. Calculate the value of the reactions at A and D and hence draw the S.F. and B.M. diagrams. C. What are the magnitude and position of the maximum B.M. on the beam?
26 - Support reactions will be found in the gerber beam whose loading condition is given in the figure. A is the fixed support, the G point is the intermediate joint, and the B support is the sliding joint. Distributed loads on the beam q1= 9 kN ⁄ m, q2= 6 kN ⁄ m, beam dimensions a = 3 m, b = 2 m. Accordingly, Bx = ?A) 19.5B) 6C) 0D) 45E) None.
(a) In Fig. a6.00-m-long, uniform beam is hangingfrom a point 1.00 m to the rightof its center. The beam weighs 140 Nand makes an angle of 30.0° with thevertical. At the right-hand end of thebeam a 100.0 N weight is hung; anunknown weight w hangs at the leftend. If the system is in equilibrium,what is w? You can ignore the thicknessof the beam. (b) If the beammakes, instead, an angle of 45.0° withthe vertical, what is w?
For the beam and loading shown, integrate the load distribution to determine (a) the equation of the elastic curve, (b) the deflection at the left end of the beam, and (c) the support reactions By and MB. Assume that EI is constant for the beam. Let w0 = 6 kN/m, L = 4.5 m, E = 210 GPa, and I = 140 x 106 mm4.
Help asap, how can I determine the deflection at point A, B, C, D and E? If E=200MPa and Ixx=169000mm4
I need help with this review problem Engineering Statics Take F1 = 40 kN, F2 = 20 kN, and d = 8 m (a) Draw a free body diagram of the entire truss. (b) Find the support reaction at A (Give the x and y components) (c) Consider a cut through members CD, DI and HI. Draw the free body diagram of the left part of cut. (d) Use the FBD of the previous question to find the tensions in members CD, DI and HI.
I need help on solving this: a) The second moment of area for the hollow cirle section can be calculated as _______ mm^4 b) Find out which of these two column types produces a better buckling performance: (i) Hollow Square Section or (ii) Hollow Circular Section.