the 4-N force exerted at A and a 300-N.mm restor-back-release mechanism. The part is subjected toDetermine the y-intercept of the line of action of theing moment exerted by a hidden torsional spring.part of an automobile seat-ExampleThe device shown is asingle equivalent force.F=4N10 mm15°40 mm300 N-mm

To find y-intercept of equivalent force

Example The device shown is a part of an automobile seat- back-release mechanism. The part is subjected to the 4-N force exerted at A and a 300-N mm restor- ing moment exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force. y F=4N 10 mm 15° A 40 mm 300 N-mm

Example The device shown is a part of an automobile seat- back-release mechanism. The part is subjected to the 4-N force exerted at A and a 300-N mm restor- ing moment exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force. y F=4N 10 mm 15° A 40 mm 300 N-mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 0.67-lb slider moves freely along the fixed curved rod from A to B in the vertical plane under the action of the constant 1.1-lb tension in the cord. If the slider is released from rest at A, calculate its speed v as it reaches B.
The boom AC in the figure rests in a ball and socket joint at A and is held in equilibrium by the cables BE and CD. The load applied at C. Determine the coordinates of D in the YZ plane so that the force in CD will be a minimum. Neglect the weight of the boom and cables. Answers: y = 16 ft; z = -34.7 ft
Determine the external reaction at the roller support in kN. Select one: a. 280 b. 30 c. 310 d. 120
Determine the magnitude of the horizontal forceF = -Fi acting on the handle of the wrench so that thisforce produces a component of the moment along theOA axis (z axis) of the pipe assembly of Mz = {4k} N ⋅ m.Both the wrench and the pipe assembly, OABC, lie inthe y-z plane. Suggestion: Use a scalar analysis.
Two cylindrical bars, AB and BC are connected at point B as shown. Knowing that d1 = 50mm and d2 = 30mm, find the voltages normal in the AB and BC stretches. Admitting that the material of stretch AB is aluminum (E = 70 GPa), and of the BC section being steel (E=200 GPa), determine the displacements of points B and C.
Determine: -vertical component of reaction at C Last time i post but answer is wrong expert did not consider moment 60 kn. M Please consider moment
Refer to the given figure below and compute for moment at force C -- (CW+) Mc
Determine the reactions in pounds the hinge and the rocker exert on the beam supporting the distributed load. (Assume that the +x-axis is to the right and the +y-axis is up along the page. Due to the nature of this problem, do not use rounded intermediate values in your calculations or answers) Magnitude and direction Magnitude in lbs. Ax- Magnitude is 0 Ay- By-
Solve this plz X1=4
When the 15KN/m load is applied to the three-member frame the support at D settles 10mm. Determine the moment acting at each of the fixed support A, C and D. The members are pin connected at B. E = 200GPa, and I = 800(10^6)mm^4.
Replace the loading by an equivalent resultant force and couple moment acting at point A.
ENGINEERING MECHANICS (UPVOTE WILL BE GIVEN. PLEASE WRITET THE COMPLETE SOLUTIONS COMPLETELY AND LEGIBLY. ANSWER IN 3 DECIMAL PLACES.) Using a ring collar the P = 613 N force can act in the vertical plane at various angles. Determine the magnitude of the maximum moment (Nm) it produces about point A. Round off only on the final answer expressed in 3 decimal places.