Explain briefly what happens when load resistances are being removed one at a time in a parallel connection.
Q: 20. Two support messengers in an expansion loop are separated by 30 cm. What's the minimum bend…
A: Given that Two support messengers in expansion loop are separated by 30cm Hence the bend radius for…
Q: When do you say that the delta-connected resistors are equivalent to wye-connected resistors?
A: To solve above question, one should know about delta and star /wye connection. Delta Connection: In…
Q: What is the expected voltage drop across each load in this circuit?
A: if the two resistors with similar resistance are connected in series then the voltage across each…
Q: e Definition of electrical series circuits and Definition of electrical parallel circuits ?
A: Electrical circuits are generally divided in two catagories series circuit consists of the all the…
Q: a.) Enumerate good practices in circuiting. b.) How to prevent overcurrent?
A: (a) Below are the following enumerate good practices in circuiting. Never touch any electrical…
Q: Why capacitance voltage dividers are not preferred for high d.c. voltage measurements ?
A: As we know that capacitance voltage divider is used for measuring the voltage.
Q: If a particular hook-up requires very large conductors, it may be better to use several smaller…
A: Here, the hook-up requires very large conductors, this large conductor is made of several conductors…
Q: If the cable in Figure ran for the whole of its length, grouped with others of the same size in a…
A: Ambient temperature – The standard or reference temperature for the installation of cables is…
Q: Question: How do the secondary voltage and current react to the different types of load and how do…
A: It is asked how in transformer the secondary voltage and current react to the different types of…
Q: have an underground buried cable, suppose the cable is derected (oper circuit) somewhere along its…
A: Given that an underground buried cable has open circuit fault and we have to locate the position of…
Q: On what depends the value of the tunneling current?
A: A quantum mechanical phenomena known as tunneling. When electrons pass through a barrier that they…
Q: differentiate between overhead service connection and under ground service connection with sketch
A: Overhead Service Connection:- Electric locomotives, trolleybuses, and trams receive their electrical…
Q: Compare different designs and suggest your design to estimate location of fault somewhere in…
A: Concept: A capacity to do work is called energy and it may exist in potential, kinetic, thermal,…
Q: Most residential general lighting circuits are wired with 14-AWG copper conductors and are protected…
A: Generally, the electricians follow the table wherein the calculated values of circuit breaker size…
Q: What is the different b/w solid type cables and pressure cables (oil and gas)...
A: There are various ways of classifying the cables and the classification depends upon various…
Q: 9/ The Underground Cable operating at a Nominal Voltage of 36 KV is classified as Super Tension…
A: The detailed answer is solved below according to the given parameters and instructions in the…
Q: Kirchhoff's voltage law (KVL) states that the sum of all voltages around any closed path (loop) in a…
A: KVL states that the algebraic sum of all the voltages around any closed path in a electrical circuit…
Q: The ladder diagram of OR gate will have two Normally closed contact in parallel. Select one: True…
A: Ladder diagrams can be used to represent boolean functions. Ladder diagrams are made of controlled…
Q: Refer to circuit shown below, Determine: (a) The equation for Kirchhoff's Current Law (b) The 3…
A:
Q: What happens to total current flow when an additional load is added in parallel?
A: when an additional load is added in parallel,
Q: Using Superposition Method. Determine the voltages at the 5-ohm resistor due to the 24-Volt, 38-Volt…
A:
Q: What is the different be Series and Parallel Circuits?
A: The explanation of differences between series and parallel circuits is as follows.
Q: What happens if a new pi equivalent circuit given the busbar admintas matrix and reactance and…
A: If a new element is added in two buses, then it will not affect the other bus matrix elements. As…
Q: Due to the effect of the resistance of the cable connected to RTD, two-wire cables up to ……. meters…
A: c) 50-195
Q: Grounding methods in Power systems
A:
Q: What is the resistance of a copper bus-bar,as used in the power distribution panel of a high-rise…
A: To solve above problem, one should know about resistance calculation of a material. The resistance…
Q: Single core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material…
A: electrical gradient in a cable is given by g=potentail differnecex lnR2R1 = Vx lnR2R1
Q: What is the difference between Shunt and Series Stub? 2. The stub is used to produce pure resistance…
A: As per our policy, i have attempted 3 parts. 1) Difference between shunt and series stub Shunt stub…
Q: The Bedding protects the Core or Conductor against corrosion and mechanical injury due to armoring.…
A: Given The Bedding protects the Core or Conductor against corrosion and mechanical injury due to…
Q: Explain briefly Series-Parallel Circuit
A: Series circuit : Series circuit is type of circuit in which the electrical components connected end…
Q: ransferred surge current method is used to find a. Fault in the transformer insulation b. Fault in…
A: Transferred surge current method is used to find Fault in the transformer insulation.
Q: Write down the KVL equation of the First loop for the circuit shown in Figure.
A: The given circuit is shown below:
Q: 3. The zero sequence current is times the current in neutral wire.
A: Zero sequence current in all phase are in phase and same magnitude . Neutral current sum of three…
Q: With lapse of time what is the change in insulation resistance expected? Why?
A: The explanation is as follows.
Q: Q4 (a) Summarize the procedure to include the effects of load current in the fault analysis.
A: Since you have posted multiple different questions. we will solve the first question for you. To get…
Q: Which type of circuit provides multiple paths for current flow so that the failure of a single…
A: In series current flow is same i.e., if one path fail current Will not flow as there is only one…
Q: under what condition may nonmetalic-sheathed cable(type NM)be finished in the hollow voids…
A: A non metallic jacket that enclosed two or more insulated conductors is known as non metallic…
Q: X.a- The figure shows a fault condition in an ungrounded electrical system. Which of the following…
A: So in question we have the figure given and based on that we need to answer the condition that will…
Q: Under Unbalanced Condition With Faults: d. The Fault Current (I)
A: We have to find the fault current from given data Three phase supply voltage Ean,Ebn and Ecn are in…
Q: For air duct in an installation type of bonding is used In Main equipotential bonding separate…
A: Ducts means passages in ventilation or heating systems to deliver and evacuate air .
Q: Refer to circuit shown below, Determine: (a) The equation for Kirchhoff's Current Law (b) The 3…
A:
Q: Explain what it means to install "conductors in parallel," and give five conditions that must be…
A: Conductors in parallel have same voltage across each other. Conductors in parallel is installed to…
Q: Why we need to use the split way in distribution panel boards?
A: The split way is used in the distribution panelboard in order to split the incoming supply into…
Q: In two way switch method, we will connected a known resistor with unknown resistor on series by…
A: We use switches in our Offices, homes, industries, motors and a variety of other places all the…
Q: Overhead service-drop conductors must have a horizontal clearance of __ from a pool. A. 6 ft…
A: Answer : (B) 10 ftOverhead service-drop conductors must have a horizontal clearance of _10ft from a…
Q: False
A:
Q: Solid conductors are either or in cross-section and are used for fixed wiring.
A: Solid conductors are either copper or aluminium in cross-section and are used for fixed wiring. -…
Explain briefly what happens when load resistances are being removed one at a time in a parallel connection.
Step by step
Solved in 2 steps
- For loop ACDBA, what is the total voltage with 30 V for V1 , 90 V for V5 , 120 V for V3 and including 240 V applied voltage?Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4what is the introduction for MEASUREMENT USING DC BRIDGES
- Explain the concept of load shedding and provide examples of situations where load shedding might be necessary.Compare different designs and suggest your design to estimate location of fault somewhere in underground cable by taking some suitable values.What is the different be Series and Parallel Circuits?
- Discuss causes of insulation failures in high voltage engineering. High voltage engineering[Fill-in-the-blank] in dwelling units shall supply only loads within that dwelling unit or no loads associated only with that dwelling unit. Select one: a. None of these b. Ground-fault protection c. Service-entrance conductors d. Branch circuitsIn residential and commercial buildings, what kind of circuit connection is being used? Is it series connection or parallel connection? Why?
- Explain briefly Series-Parallel CircuitSingle core cable design for 25 kV. The radius of conductor is 0.5 cm. The insulation material consists of two layers. The thickness of each layer is 2 cm. The voltage of first and second layers are 20 kV, 5 kV respectively. The minimum Electric stress of the cable is *The Bedding protects the Core or Conductor against corrosion and mechanical injury due to armoring. Select one: True False
