Explain five (5) applications of the hall effects With the aid of a diagram, explain how a P-N Junction is form. State five (5) application of PN Junction, and explain the property of the PN junction that make those application possible. Explain what carrier mobility is and elaborate on the factors that influence carrier mobility. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is a. rectified using a half wave rectifier circuit and connected to a 47.5 Q load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage.

Explain five (5) applications of the hall effects With the aid of a diagram, explain how a P-N Junction is form. State five (5) application of PN Junction, and explain the property of the PN junction that make those application possible. Explain what carrier mobility is and elaborate on the factors that influence carrier mobility. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is a. rectified using a half wave rectifier circuit and connected to a 47.5 Q load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain five (5) applications of the hall effects With the aid of a diagram, explain how a P-N Junction is form. iii. State five (5) application of PN Junction, and explain the property of the PN junction that make those application possible. Explain what carrier mobility is and elaborate on the factors that influence carrier mobility. A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is rectified using a half wave rectifier circuit and connected to a 47.5 Ω load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage. Calculate the following about the circuit in Figure 2.1 (If silicon diodes are employed in the rectification); the peak value of the output voltage considering the drop across each diode, the average voltage, iii. The current through the load resistor, The current diode, The frequency of the output signal, Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch…
Describing the concept of discontinuous conduction mode in power converters, how does continuous conduction mode differ?Make a DC-DC converter circuit that operates in discontinuous conduction mode.
What is the maximum dc voltage you could expect to obtain from a transformer with an 18 Vrms secondary using a bridge rectifier circuit with a filter capacitor? in your own words
Some electronic devices operate on a DC voltage of 7.5 V. To obtain 7.5 V DC from a 120-V (rms) AC line, first the voltage is dropped to 7.5 V (rms) AC by a transformer, and then the 7.5 V AC is converted to 7.5 V DC by a rectifier circuit involving diodes. Consider a device of resistance 15 Ω connected to the 7.5-V DC output of the rectifier. Again assuming no power loss anywhere, what is the rms current, in milliamperes, in the primary winding?
2.A single phase uncontrolled half wave rectifier has a transformer with a turns ratio of 5:1, has a source of 220Vrms at 60 Hz frequency, its supplies the load with a 100ohm resistance. Find: A. Average voltage and current and also in RMS B. Power and ripple factor
Derive the current equations for the circuit shown below, using the labels as shown.Note that rz here is a model of the parasitic imperfection of the Zener diode.a) IL = ?b) II = ?c) IZ = ?d) What impact does rz have on VL?
(i) With necessary sketch, write the load current flow path of a single phase semi converter during freewheeling period. Assume the load have resistance and high inductance value and the semi converter requires multiple gate pulse for triggering. (i) Draw the circuit diagram of the single phase half wave controlled rectifier (RL load) with center-tapped transformer and compare its performance with uncontrolled rectifier operation.
What is scientific Reason? c. Elaborate why Depletion Zone inside P-N Junction is a problematic area? What necessary measurement should be taken to remove the depletion zone?
in Steady-State Operation of Boost DC-DC Converter, What is the maximum voltage occurs across the switch in your practical results? Is there any difference between practical and theoretical results? Comment.
Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary. (2nd Approximation)
Describe the operating principle and characteristics of a typical Zener diode found in the market place, including examples of their common applications. The circuit shown below is to be used to provide a stabilised output to the load. The Zener diode characteristic is also shown on the next page. Find the load voltage (VL) and source current (IS) if the battery voltage is 18 V, series resistance is 1.4 KΩ and load resistance is 11 KΩ. Additionally, determine the value of the source resistance (R) if the Zener diode is at the threshold of activating in its reverse bias. Comment on the purpose of having this value of R in the circuit.
What is the maximum value of vs(i.e.vsm ) Find the peak-to-peak ripple voltage vr Find the average output voltage Vo in steady state Find the average diode current ID in steady state. If the secondary winding resistance of the transformer is 1.5 Ω, calculate the maximum surge current in the worst-case scenario