Explain the five most common uses of CAD/CAM software using concrete examples. You may learn more about the potential applications of simulation by reading academic publications on the topic. Nothing needs to be tackled simultaneously.

Q: Problem 4. A receipt of surface water sample is given in Table below: Substance Concentration (mg/L)…

A:

Q: A load 600kN applied at point A, as shown in fig above, produces a vertical deflection at A, B and C…

A: Given: Load 600 kN applied at point A, Load 200 kN applied at point B, Load 400 kN applied at point…

Q: Determine the support reaction 335 KN A 4 m + B 4 m forces of each given beam. 180 kN Hinge 0 4 m D…

A:

Q: Determine the force in member CG. The force is positive if in tension, negative if in compression.…

A:

Q: For the beam shown in Fig.Q4, use the principle of virtual work to determine (1) the vertical…

A: Given: q= 15KN/m P= 27 KN Required: Support reactions and deflection at C

Q: Situation 4: A W530 x 92 simply supported beam has a length of 12 m. The beam supports a super…

A: NOTE : Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The pressure drop of water in a pipe is measured by a manometer using a liquid of density 2000…

A: Given data- Density of the liquid- ρm=2000 kg/m3, The difference in height h=10 cm=0.1 m, To Find-…

Q: catchment's outlet has an annual discharge of 0.80 m^3/a. It's size is 250 km^2. The annual…

A:

Q: 100 KN . m G 2m 2 m 25 kN/m -4 m. + 4 m 150 KN 4 m m

A:

Q: In a rectangular beam of size 200 mm x 400 mm, if the ultimate shear force due to design load is 80…

A: Width b=200 mm, Depth d=400 mm, Ultimate shear force due to design load=80 kN,

Q: 1. A built-up column has a length of 6 m. If consist of a core of W360 x 382 with two plates having…

A: Given,  L = 6 m or 6000 mm  Kx = 1  Ky = 0.85 Fy = 250 MPa

Q: What are the various limit states of design for a steel structure as per IS: 800-2007?

A: Given: steel structure To determine: various limit state of design for steel structure as per IS…

Q: For the branching pipe system in the figure below, if the discharge through pipe A is given, which…

A: The branching pipe system is given in the above figure. Discharge through pipe A is given.  We have…

Q: The flooring of a warehouse is made up of double - tee oints. The joints are simply-supported on a…

A: Data Provided : simply supported span ( L ) = 8 Meter One tendon in each stem  Initial Jacking force…

Q: GF Q2: Estimate the peak flowrate for a catchment which has an area of 10 km². The length and slope…

A: Answer  We know that peak flow rate is given by Q = A*I*R360 where  Q = peak flow rate in m3/sec A =…

Q: At a section of a shaft, a bending moment of 8 kN-m and a twisting moment of 6 kN-m act together.…

A: Given- Bending moment M=8 kN-m, Twisting moment T=6 kN-m, It is needed to find the equivalent…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: An infinitely long slope is made up of a C-o soil having the properties cohesion (C) = 20 kPa and…

A: Given- Cohesion C=20 kPa, Dry unit weight γd=16 kN/m3. Angle of inclination=40o, Critical length of…

Q: 2. For the bea moments ar

A: To determine: SFD and BMD using method of superposition

Q: A wooden beam is loaded by a concentrated load P = 2000 N and supported by boundary conditions as…

A: Answer  (b) Let us first draw the free body diagram and calculate the support reactions at A and B.…

Q: A fluid is flowing over a flat plate. At a distance of 8 cm from the leading edge, the Reynolds…

A:

Q: Q2 - the magnitude of the minimum normal stress in the beam and where within the beam it is…

A: To determine The magnitude of the minimum normal stress The location of the minimum normal stress

Q: During the construction of a highway bridge, the average permanent load on the clay layer is…

A:

Q: H.W2: Draw I.L for a E 1 A TI F B a 3@6m=18m G C D H 8m

A: Solution: Draw the Influence line for the forces in members EC of the given truss.

Q: A two-stage cyclone (i.e., two cyclones in series) is designed to remove particulate matter from the…

A: Given:- The geometric mean diameter = 10 μm The geometric standard deviation = 2 To determine:- The…

Q: A timber beam, 100 mm wide and 150 mm deep, supports a UDL over a span of 2 m. If the safe stresses…

A: Given data- A timber beam- Width b=100 mm, Depth d=150 mm, UDL on the span L=2 m = 2000 mm, Safe…

Q: A fluid is flowing over a flat plate. At a distance of 8 cm from the leading edge, the Reynolds…

A: Given- Reynold's number Re=25600, Distance x=8 cm = 0.08 m,

Q: a) Use the principle of virtual work to determine the rotation at Support B. (The postive direction…

A: Given: q = 14KN/m P = 35 KN Required : Rotation at support B

Q: Determine the reactions at the beam supports for the given loading: 2 distributed A 2.20 kN/m 2.90…

A: To find support reaction

Q: A cable suspends across a gap of 250m and carries a UDL of 10KN/m horizontally calculate the maximum…

A:

Q: 5. According to Fig. 5, the beam AC is simply supported at A and C and is subject to a load that is…

A: Given:- The beam is simply supported at point A and C The magnitude of the distributed load = 300…

Q: Question: A three-story office building has interior columns that are spaced 6m apart in two…

A: The given data is as follows: Spacing between interior columns=6 mRoof loading=0.96 kPa

Q: In the case of a beam simply supported at both ends, if the same load instead of being concentrated…

A: Deflection at centre of S.S.B at point load = WL³/48EI Deflection at centre of S.S.B at UDL =…

Q: Determine the magnitude of the force which member CD exerts on the pin at C. A 125% B 0.63 m Answer:…

A:

Q: Old Southwest Canning Co. has determined that any one of four machines can be used in its…

A: Since in the given data cash flow rate is only given, no information regarding the revenue is…

Q: Problem I Compute for the moments at support of the beam loaded as shown: 0 MA THREE MOMENT EQUATION…

A: Given data Find the moment at the support and support reaction using Three moment equation.

Q: Given the table below, determine the BULK SPECIFIC GRAVITY OF GROUP 3. Data and Results Weights…

A:

Q: 6. A dam 4m on top 18m at the bottom and 25m high has water 20m deep acting on its vertical sides.…

A: The pressure at bottom of dam =Given:B = width of dam bottom =18mH = height of water acting on dam…

Q: What is the average skid resistance of the pavement surface when a vehicle travelling at a speed of…

A: Given that :- Length of skid marks  = L = 8 m Speed  = U = 36 kmph To Find the average skid…

Q: Steel column pinned at both ends has a modulus of elasticity E = 2 x 105 N/mm², moment of inertia I…

A: Given- Steel column pinned at both ends E=2×05 N/mm2I=90000 mm4 Length L=1.75 m

Q: A typical serious candidate for services examination take no less than 25 minutes to answer a…

A:

Q: (1 - ++ e) (Gs+ Se) Xu A I te WHY OR HOW DID THIS BECOMES 1 (Gs + Se) Xw

A:

Q: A structural beam subjected to sagging bending has a cross section which is an unsymmetrical I…

A:

Q: At the proportional limit, a 29 mm wide by 12 mm thick bar elongates 1.7 mm under an axial load of…

A:

Q: It is desired to determine the location of the free-surface, y, in a contained fluid undergoing…

A: Given that, the location of the free surface (y) is to be expressed as a function of angular…

Q: determine the following Activity 1-2 1-3 2-4 3-5 4-9 5-6 5-7 6- (To) 6 2 6 4 2 4 5 (Tm) 9 4 8 7 3 7…

A:

Q: Ass: maximum velocity that pass through a vag parabolic curve having sight distance of 500 ff when…

A: Answer  We are given Sight distance S = 500 ft G1 = -1.5% G2 = 2.5% Calculations shown in steps…

Q: If design bond stress = 1.5 N/mm2 is assumed, then the development length of an Fe 500 HYSD bar of…

A: Given- Design bond stress τbd=1.5 N/mm2,Nominal dia ϕ=12 mm, It is needed to find the value of the…

Q: Find the angle 8. 5.6 kips 33° 14> B Answer: 0 = i C 2.3 kips 7.7' S 7.7'- C 7.7' 0 E

A: Given Data  Find the angle θ

Q: With the water levels in the high plains aquifer still dropping precipitously, what should be done?…

A: The given question has the following parts 1. Water levels in high plain aquifer dropping…