Explain what is meant by the tolerance percent defective ?

Q: No Go holes and H7/p6 tolerances

A: 10 H7/p6   Hole dimensions from a standard tolerance chart for 10mm H7 tolerance is +15 therefore…

Q: 14. What size internal chamfer is required for the part? 14. 15. Why does the flatness tolerance not…

A: 15. Why does the flatness tolerance not reference a datum

Q: Give any four significance of ASTM Standard?

A: ASTM stands for American Society for Testing and Materials. ASTM is an organization that indulges in…

Q: Tell us about the tolerance zone in operations.

A: As per given  we have to detail describes about tolerance

Q: Q13) For the following micrometer: a- What is the part diameter?

A: 13

Q: Match the allowance and limit parameter in

A: Given data; Column given below; Column 1= Allowance and limit paramater Column 2=Quantitative…

Q: pes o

A: GIVEN: Explain different types of fits?

Q: c) Evaluate the performance of Static Cone Penetration Tests

A: The Static Cone Penetrometer is utilized to assess the consistency of soils, their level of…

Q: write an introduction for hardness test lab

A: Hardness Measurement methods.

Q: Explain Precision & Accuracy with the help of industrial applications

A: Explain Precision & Accuracy

Q: HW001 What things we measure with the help of vernier?

A: Given data⇒ Vernier

Q: Compare one point vs two point calibration: explain how it affects the measurement curve and…

A: The simplest sort of calibration is one point calibration. A one-point calibration can be…

Q: the case where circular runout has been applied to an end face of a shaft, the following is…

A: Since the circular runout provides both concentricity and circularity with inherent influence. It…

Q: Why cracks of pmma need higher energy to grow than ps

A: It is a reasonable, drab polymer accessible in pellet, little granules, and sheet structures, which…

Q: What is the algebraic difference between the lowest limit of size dmin and the nominal size da (dmin…

A: The correct option is 4 (the lower deviation ei), Lower deviation is the algebraic difference lower…

Q: Unilateral Tolerance is Total tolerance is in both the directions May or may not be in any direction…

A: Unilateral tolerance is the type of tolerance in which true profile is only permitted in one…

Q: 2. Form tolerances are independent of all other Features Size Limits Datums ?

A: Form tolerance is a geometric tolerance that defines the roundness, flatess, straightness of a part.

Q: (a) Identify the types of failure on a diagram below

A: (a) To identify: The types of failure. Explanation: Brittle failure: The failure occurs due to…

Q: Give any four significance of API Standard

A: American Petroleum Institute (API) Standard:-  American Petroleum Institute of standards Improve…

Q: Describe the concept of finding toughness using impact testing machine.

A:

Q: ving data were recorde tensile test of a 12.8 m teel rod. The gauge 5 50 mm. ress-strain diagram anc

A: Calculate the cross section area of test specimen of mild steel. A = π4 d2 Here A cross section area…

Q: The inner radius of clutch plate is 100mm and the outer diameter of the clutch plate is 400mm. what…

A: Write the given data with suitable variables. ri=100 mmdo=400 mm%ri=50%

Q: Slip gauges are standards used along with sine bar for direct angular measurement of workpieces in…

A: Slip gauges are standardize pieces of metal with specific size to a greater degree of accuracy. they…

Q: What is the minimum distance from the holes at each end of the part? - 2x Ø 1.375-1.390 +Ø010 LABC…

A:

Q: Match the following statements with the term that best describes each statement.  hooks law creep…

A:

Q: Tolerance Maximum Limit Minimum Limit 50.7 mm 49.9 mm 26.8 cm 26.6 cm 0.04 mm 0.12 mm 258.03 mm…

A: Given data

Q: 1. AISI steel designation for plain carbon steel. 2. In GD&T, what does this indicate 3. A fit…

A: Steel designations are the ways to define the different plain carbon steels.

Q: 15. On the produced part below, show a simple sketch on how the flatness on the part m verified and…

A: Flatness:- It is defined as the minimum distance between two planes within which all the points on…

Q: Explain the purpose of the v-notch on the specimen for Charpy Test.

A: Charpy test: The Charpy test is also known as Charpy V-notch test for toughness of material. Charpy…

Q: Which type of feature doesn't belong to form tolerances? Circularity The profile of a surface…

A: As we know principle component of form tolerence are Straightness.Flatness.Roundness.Cylindricity.

Q: as the following standard

A: given data shaft dia = 60 mm length of key = 50 mm b = 18 mm h= 11 mm torque T = 350 x 1000 N-mm…

Q: All form tolerances are surface controls except for Form tolerances are independent of all other and

A: Form tolerance is a used to determine the form of the part. It refers to the limitation of a form…

Q: what are plug gauges ? how to use them to judge a qualified part?

A: Different types of gauges used in metrology are: Plug gauge Snap gauge Ring gauge Thread gauge, etc…

Q: Why ceramic block gauges is better than steel slip gauges?

A: Option (b) Due to its resistance to wear  is correct option

Q: 2) Explain the principle of working and operation of Ultrasonic Inspection with neat diagram.

A: To find Working of ultrasonic testing

Q: There is a difference in how "Amplification" is achieved on Mechanical Dial Indicators and Lever…

A: Mechanical Dial Indicators and Lever Type Dial Test indicatorss

Q: 8) __________ notched specimens are used for Charpy impact test. Select one: V U & V U Key hole

A: V notched specimens are used for charpy impact test

Q: Is the 'fit' between the 2 parts shown below a clearance fit or interference fit?

A:

Q: How would a small or tight tolerance affect the layout?

A: The lines that are used for locating the points on the objects and items for the purpose of cutting,…

Q: Sketch and explain the working principle, constructional details, and application of a dial test…

A: Dial Test Indicator :

Q: What tolerance is specified for the width of the groove?

A: Given :-   Bolt Drawing   Find :-  Tolerance of the width of the drawing

Q: Explain the Bathtub curve as it refers to failure

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Define the Rockwell Scale

A: Rockwell method: It is a hardness testing method that is used to measure the hardness of any metal…

Q: What are the strain gauge types and applications?

A: strain gauges I)  Strain gauge is a type of sensor. Whose resistance is varies with applied force.…

Q: If you know the value of tolerance Tp and the upper deviation ES, then by what formula is the lower…

A:

Q: Bilateral tolerance is Total tolerance is in 1 direction only Total tolerance is in both the…

A: As per our guidelines we are supposed to answer first one .Kindly repost other question as a…

Q: 1. Is the 'fit' between the 2 parts shown below a clearance fit or interference fit ? 2. Which…

A:

Q: Go Plug Gage NOT Go Plug Gage Nominal size: Nominal size: Tolerance: Tolerance: Class: Class: Max…

A: