F 0.5 S 0 UBC Engineering N A block of a mass of 6 kg and a spring with a k value 30 as shown in the diagram shown below. The m kinetic μ has a value of μ = 0.2 the applied force F = 60 N. Assume the block is already in motion (only use kinetic coefficient) and there more the spring is already compressed by 0.5 m. What is the magnitude of work done by force, spring, and total work after the system comes to an equilibrium?

F 0.5 S 0 UBC Engineering N A block of a mass of 6 kg and a spring with a k value 30 as shown in the diagram shown below. The m kinetic μ has a value of μ = 0.2 the applied force F = 60 N. Assume the block is already in motion (only use kinetic coefficient) and there more the spring is already compressed by 0.5 m. What is the magnitude of work done by force, spring, and total work after the system comes to an equilibrium?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Similar questions

There are two double-acting pneumatic actuators, the extension of each one is executed in 5 seconds at 80 psi and recoil in 4 seconds at 30 psi, the travel of both is 12 inches, the diameter of the piston is dp = 4 "and of the rod dv = 1"a) Determine the compression ratios. The local atmospheric pressure is 79kpa = (11.5 psi)b) Determine the air consumption in cubic feet per minute of free air PCMc) Determine the average air consumption for each.d) Propose the regulation values of the pressure switch, system pressure and safety valve
A stone is dropped from a bridge and allowed to free-fall downward. As it falls a certain distance its gravitational potential energy decreases by 1000 J. By how much does the stone's kinetic energy increase? (Neglect air resistance). a) 100 J b) 2200 J c) 500 J d) 1000 J
A 20 kg box is released from rest and let slide down a 25˚ ramp. If the box/ramp kinetic friction coefficient is uk=0.20m what should be the minimum spring constant of the spring attached to the box so that the box stop before reaching the bottom of the ramp 0.5 meters below the starting point? (Assume the spring is neither stretched nor compressed) a. 110 N/m b. 190 N/m c. 280 N/m d. 410 N/m
Thermodynamic problem. ou have a system in which we can go from point A to point B using two equations for pressure as a function of volume.p1(V) = 1atm + (0.25 atm/ lt^2 ) V ^2 and p2 (V) =(1.25 atm/lt) V a) Verify that the pressure is the same for both equations when the volume is Vi=4lt and Vf=1lt.b) Would you expect the work to be the same? in compression work given these volume values?c) Calculate the work in both cases, compare and explain.
SUMMARIZED IN YOUR OWN WORDS THE RELEVANCE OF IST AND SECOND LAW OF THERMODYNAMICS IN YOUR CAREER AS A CIVIL ENGINEER
A box with a mass of 3m is on frictionless ground, attached to a wall (on the left-side of the box) by a spring with constant k. Inside the box (on the frictionless floor of the box), is a block of mass m. The block is also attached to the left-side of the box (but inside it), by a second spring, with a spring constant 2k/5.1) What are the F = ma equations for the box and the block? (Remember how the motion of each, affects each other)2) What are the matrices K and M for the system?3) What are the normal frequencies of the system?4) Describe the motion of the masses. In phase? Out of phase? Does one mass oscillate with a higher amplitude than the other?
A power station with an efficiency e generates W watts of electric power and dissipates D J of heat energy each second to the cooling water that flows through it. The cooling water increases its temperature by T degrees of Celsius. Find the mass of cooling water which flows through the plant each second. Specific heat capacity of water cw = 4,184 J/kgC e = 0.2W = 4.9 x 108 wattsD = 2.5 x 108 JT = 4 C Enter value in tons (1 ton = 1000 kg).Enter two digits after decimal point.
A gas-filled piston-cylinder unit with volume 2 m³ compressed and pressure 100 kpa. On the piston page. An nika constant spring of 200 kN/m . The units are then heated and Causes the volume of gas to increase to three times the volume of the original, which is pressing Springs. If it is known the surface area of the unit is 0.3 m² radius, a). The final pressure in the cylinder B) A work done with gas c) A work done with springs
A forced draft centrifugal fan draws air at 1.32 cubic meter/sec towards a combustion chamber of a steam generator. The static pressures are 15mm. water below atmospheric at suction and 10mm. water above atmospheric at the discharge. The inlet duct is 30cm in diameter and the discharge duct is 27cm in diameter. The fan mechanical efficiency is 70%. The air is measured at 25 degrees Celsius and 760mmHg. Determine: a. the Air Power in kW 0.664 0.464 0.546 b. the Brake Power in kW 0.546 0.464 0.664 c. the static efficiency 50.00 48.77 52.03
There is a spring-mass system, driven by an external piston, which applies a force to it. Newtons that satisfies the following relation F = 6*cos (3*π*t), as can be seen in the figure, it is known that the spring constant has a value of k = 25 Nm, and the block has a mass of 4 kg, furthermore, dissipative frictional effects cause the relationship between velocity and force to satisfy the ratio F = bv, where b is the damping constant, and it is known that the numerical ratio of force is 10 times the value of speed. Determine: a) The natural frequency of the system. b) The driving frequency of the external force. c) The maximum value exerted by the external force. d) The damping constant. e) The amplitude of the forced oscillatory motion in steady state. f) If dissipative (damping) effects are neglected, what is the value of the amplitude.
Initial condition: P = 8 MPax = 100%m = 5 kgProcess: IsothermalFinal condition: Q in KJ = 75% of h1Required: Work
A 15-kg mass block rests on a frictionless inclined plane at 35 degrees. The spring is originally stretched 0.25 meters. What is the total work done, if the spring constant k = 30 N/m and s=3m?