When force F = 1375 N and uniformly distributed load qo= 490 N/m are applied to rigid beam ABC itવાrotates clockwise through angle = 0.3°. The geometry is such that L = 2 m and h = 2.2 m. Determine thetension and normal strain in cable DE under the applied loads. You may assume the cable is made of steel andthe beam is originally horizontal before any loads are applied.TBC =EBC1898.2FA| ¼½ +² +² -Lnumber (rtol=0.01, atol=1e-05)N O?9ThBqo

GIVEN:- F= 1375 qo= 490 N/m θ= 0.3o, L=2 m, h…

Answered: -F A B C T h

Engineering

Civil Engineering

-F A B C T h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: *2-12. Classify each of the frames as statically determinate or indeterminate. If indeterminate,…

Q: Analyze the beam loaded and supported a shown: 40 kN Ans.: A| 2 Ans: 6m B Hinge (a) Determine the…

Q: I will downvote the incorrect solution..A lot has a frontage of 120 m along a road. The other sides,…

Q: Sta. 1 N345 2 Deflection angle 90°00' R 136°25' R 91°15' L 132°21' R 97°29' R Bearing DUE EAST

Q: Answer 4.3

Q: A beam subjected to weather upon concrete pouring has a dimension of approximately 310 mm by 555 mm…

A: Given Beam dimensions b = 315 mm D = 555 mm Assume nominal cover = 30 mm Effective depth of beam…

Q: Find the forces in members EF, KL, and GL 30° JP k 'N 10 kN L F 20 kN 0 M 6 panels at 5 m K G 20 kN…

Q: 4. For the concrete dam shown, calculate the factor of safety against overturning and sliding. Use…

Q: Question 14 Six columns of building are to be located within the plot size of 15x10m. The expected…

A: Given- 6 columns in the building, Plot size- 15×10 m, Load on each column=600 KN, Allowable bearing…

Q: Angle Check: 101 102 103 104 Bearing Dec AZ LAT Closure : DEP Closure : Linear Error of Closure :…

A: A bearing is an angle less than 90° within a quadrant. An azimuth is an angle between 0° and 360°…

Q: Problem 3 in the steel structure shown, a 6-mm-diamter pin is used at D and 10-mm-diameter pins are…

Q: Draw the shear and moment diagrams for the beam shown. After you have the diagrams, answer the…

A: Given : To Find :

Q: The system in the figure is at 20°C. If the pressure at point A is 1900 lb/ft², determine the…

A: A pipe system is given in the figure as shown in the figure above and it has been asked in the…

Q: Compute the location of zero shear from support A.

A: Given: Ay = 6 KN and By = 10 KN Required: Location of zero shear from A

Q: has an order to manufacture 5000 hanging vases to hold ½ pt. of water when full. The vases are…

A: Given:- 5000=manufacture 1/2 point of water height=8 in weighs =130 lb per cu ft To find:- weight…

Q: A 2 kN/m 6m 6 kN 4m 2m

Q: For a certain interval of motion the pin A is forced to move in the fixed parabolic slot by the…

A: From the given equation by using the value of x=4 the value of y can be calculated.

Q: Identify specific examples of terms and conditions to include in the project contract.

A: Project management : Construction project management entails coordinating and arranging every stage…

Q: A carpenter holds a 10-lb 2-in. by 4-in. board as shown. If he exerts vertical forces on the board,…

A: Given, W= 10lb Vertical forces are NA&NB, Free body diagram:-

Q: A retaining wall, 4.5m high has a smooth vertical back. The back fill has a horizontal surface in…

Q: Q- A 2 km long pipe of 0.2 m diameter connects two reservoirs. The difference between water levels…

A: Given- Length of pipe L=2 km, Diameter D=0.2 m, Head difference h=8 m, friction factor f=0.04, It…

Q: A carpenter holds a 17-lb 2-in. by 4-in. board as shown. If he exerts vertical forces on the board,…

Q: Draw the V and M diagrams. Find Θa, θB and θC. show all steps

A: Using slope selection method

Q: An existing rectangular clarifier at a drinking water treatment plant is 18 ft wide and 72 ft long.…

A: Rectangular Clarifier: The rectangular shape of the clarifier provides a longer path for effluent…

Q: T d + d N d LA F₁ M 17. Enter F cd 18.Enter F ld O 19.Enter F kl B F2 F3 F₁ K C DE dddddd The truss…

Q: For the truss shown, determine the force in member BD, member CD and member DE. Report answers as a…

A: Given : Determine the force in member BD , CD and DE?

Q: Differentiate between 'low gravity' and 'high gravity' dams. Calculate the limiting height of low…

Q: Find the forces in members EF, KL, and GL B 30⁰ D E 10 kN 'N L F 20 kN 0 M K 6 panels at 5 m G 20 kN…

Q: This is Structural Theory. Evaluate the structural stability of the following structures. If stable,…

A: Using formula to find static indeterminacy

Q: Estimate the total amount of cost (Php) for concrete works (class "A") based from the following…

Q: PROBLEM 4 A truss is loaded with nodal force at C as shown TOS-003. If the truss members have…

Q: A triangular channel carries a flow of 2.4 cumecs laid on a slope of 0.001 with n=0.012. If the…

A: Given data Discharge (Q) = 2.4 m3/sec Slope (S) = 0.001 Manning coefficient (n) = 0.012 Notch angle…

Q: 6-6. Determine the force in each member of the truss, and state if the members are in tension or…

A: Given : Determine force in each member of truss

Q: Q- In its natural condition, a soil sample has a mass of 1.980 kg and a volume of 0.001 m³. After…

A: Given data: Mass in natural condition, M=1.980 kg. Volume, V=0.001 m3. Mass in dried condition,…

Q: A concurrent force system in space is composed of 3 forces described as follows. P₁ has magnitude of…

A: Reference : Mechanics, Concurrent force system. Given : Magnitude and the origins and their points…

Q: 7. Using the graph of sample height vs. log time, determine the coefficient of consolidation c, in…

Q: 15.1 Refer to the braced cut shown in Figure P15.1. Given: y = 17 kN/m³, ' = 35°, and c' = 0. The…

A: In this problem we have to find earth pressure envelope and determine the strut loads at level A,B…

Q: determinate, statically indeterminate, or unstable. If indeterminate, specify the degree of…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Activity 4.1 Determination of the Slope of a Curve at a Given Point Find the slope of the tangent…

A: Finding slope of curve

Q: A Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(106) mm².…

Q: Q1. If the absolute pressure in a tank is 140 kPa, determine the pressure head in mm of mercury. The…

A: Determine the pressure head in mm of mercury.

Q: 4.9 The maximum and minimum dry unit weights of a sand were determined in the laboratory to be 18.31…

A: (4.9)

Q: Solve the following and submit with the same format of this module, A4 size: 1. Determine the…

A: For W 10x 33 The radius of gyration, r = 1.94 in Gross area, Ag = 9.71 in2 For A992 steel Minimum…

Q: 3. A new office park is considering to start an express bus service for workers. A survey of office…

A: Most studies aim to predict the share of trips made by each mode or the absolute number of trips…

Q: 2. Distribute the trip produced and attracted between 3 zones using the following tables of data…

A: Data given

Q: The mass center G of the 1535-kg rear-engine car is located as shown in the figure. Determine the…

A: Given: Load=1535kg Distance between front wheel and G=1309mm Distance between G and back wheel…

Q: Q. 25. A conical draft tube having diameter at the top as 2m and pressure head at 7m of water…

Q: 6.8 Refer to Figure P6.8. Using the procedure outlined in Section 6.8, determine the average stress…

A: The given figure is shown below:

Q: The mass center G of the 1535-kg rear-engine car is located as shown in the figure. Determine the…

Q: Q- What is end depth in free overall?

A: the solution of above problem is below:

Concept explainers

Steel Framing

A steel frame consists of a skeleton frame structure comprising of horizontal I-beams and vertical steel columns fitted in a rectangular grid building construction to brace the floors, walls, and the roof of the building held onto the frame. Due to the implementation of this methodology, the construction of the skyscrapers was feasible.

Question

When force F = 1375 N and uniformly distributed load qo= 490 N/m are applied to rigid beam ABC it
વા
rotates clockwise through angle = 0.3°. The geometry is such that L = 2 m and h = 2.2 m. Determine the
tension and normal strain in cable DE under the applied loads. You may assume the cable is made of steel and
the beam is originally horizontal before any loads are applied.
TBC =
EBC
1898.2
F
A
| ¼½ +² +² -
L
number (rtol=0.01, atol=1e-05)
N O
?
9
T
h
B
qo

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cable in Figure P6.2 supports four sim-ply supported girders uniformly loaded with 6 kips/ft.(a) Determine the minimum required area of the maincable ABCDE if the allowable stress is 60 kips/in.2.(b) Determine the cable sag at point B.
The cable supports the loading shown. Determine thedistance y and the tension in cable BC. Set P = 3 kN.
The cable ABCD is held in the position shown by the horizontal force P.Determine P and the force in each segment of the cable.
Compute the support reactions and the macimum value of w if the allowable tension force in the cable shown is 200 kN.
1. Compute the maximum tension in the cable. 2. Compute the tension at member BC 3. Compute the sag at point B.
Solve Prob. 3.53 when the tension in cable AB is 306 lb
Compute the support reactions and the maximum tension in the cable in Figure P6.6. Show all the solution and fbd.
A uniform cable weighing 15N/m is suspended from points A and B. The force in the cable at B is known to be 500N. Using the result of Prob. 6.69 , calculate (a) the force in the cable at A; and (b) the span L.
Determine the location of the 40-kN load such that sags at points B and C in the figure are 3m and 2m, respectively. Determine also the maximum tension in the cable and the reactions at support A and D.
2. Forces (Figures Needed) 2.4. Two cables are tied together at C and loaded as shown. Knowing that P= 360N,Determine the tension in cable BC and AC. 1 Free-body Diagram only
Determine the force P needed to hold the cable in the position shown, i.e., so segment BC remains horizontal. Also, compute the sag yB and the maximumtension in the cable.
The cable supports the loading shown. Determine themagnitude of the vertical force P so that y = 4 m.