F7.3 Determine the forces in members CD, HJ and CJ knowing that the loads supported by the Pratt truss are: B = 175 lbs, D = 175 lbs, and J = 325 lbs. Indicate tension or compression. E F B C 7.5 t A H + panels @ 6-24 t

F7.3 Determine the forces in members CD, HJ and CJ knowing that the loads supported by the Pratt truss are: B = 175 lbs, D = 175 lbs, and J = 325 lbs. Indicate tension or compression. E F B C 7.5 t A H + panels @ 6-24 t

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 11P

See similar textbooks

Related questions

Q: Ex. A 4.0 m wide rectangular channel carries a discharge of 12.0 m³/s at a depth of 2.0 m. Calculate…

Q: Q- A rectangular open channel of 6 m width is carrying a discharge of 20 m³/s. Consider the…

Q: DESIGN A SEPTIC TANK FOR A SMALL COLONY OF 300 PERSONS WITH AVERAGE DAILY SEWAGE FLOW OF 81 LITRES…

Q: A Single rivet lop joint is to connect 12mm thick plates by providing 20mm dia. rivet at so mm…

Q: A column is made of steel and concrete, if the normal forces on steel and concrete are 6.8kip and…

A: Given : Normal force on steel = 6.8 kip Normal force on concrete = 145 kip Allowable stress of…

Q: forward tangent is -3.0%, and the location of the highest point elevation of the highest point is…

Q: A rectangular beam has a width of 400 mm, and effective depth d=700 mm to centroid of tension steel…

A: Answer We are given Width b = 400 mm effective depth d = 700 mm Tension steel rienforcement As =…

Q: An isolated T-beam is used as a walkway. The beam is simply supported with an effective span of 6 m.…

Q: A 116.79 kips (B 172.79 kips 92.79 kips A 119.38 kips B 40 kips 1.5" V 40 kips C From the figure,…

Q: 3Q. An oil pipeline has a 12 inch diameter, and the oil in it flows at an average velocity of 4.0…

Q: Given a 2.7 m, and b = 6.0 m, = y Iy b = a determine the moment of inertia of the area about the…

Q: Enumerate at least 10 types of water pollutants found in sea waters and river waters (salt water and…

A: Marine and river pollutants and their treatment are as following .

Q: Determine the reactions at the support A, B and C using force method. El is constant. 12ft BO Note:…

A: Given: To find: Reactions at supports A, B, and C using the Force method.

Q: 6. Calculate the location of the centroid (x and y) of the area shown below. All dimension are in…

A: To determine the location of the centroid.

Q: Explain (in short answer) how the dimensions of metric modular block, brick, and rigid insulation…

A: Masonry Cavity Wall: A masonry cavity wall is a wall that is made by composing two separate masonry…

Q: a liquid compressed in a cylinder has a volume of 1500cm³ at 1 mn/m² and a volume of 1495 cm³ at…

Q: A fillet-welded joint of 6 mm size is shown in the figure. The welded surfaces meet at 60-90 degree…

Q: 8-62 A horizontal pipe has an abrupt expansion from D₁ = 8 cm to D₂ = 16 cm. The water velocity in…

A: We have to find out the downstream pressure P2 and error if bernoulli's equation is used .

Q: A simple beam of 15ft span has a concentrated live load of 15kips at its mid-point. The beam also…

A: Given: span = 15 ft LL = 15 kips (at mid-point) UDL: DL = 3 kip/ft LL = 1 kip/ft Braces at every 5…

Q: 3. A 200 lb man climbs up the ladder and stops at the position shown after sensing that the ladder…

Q: 14.3 Identify the type of CMU block shown below VERTICAL REINFORCEMENT AS REQ'D VIEW OF STANDARD…

A: Type of CMU

Q: EXAMPLE: For the foundation shown in the below; estimate quantity of Reinforcement. Depth of…

Q: polygonal lot: & a quadrilateral lot.) LINE AB BEARING N4825 E BC CD DA 139 S 50°18'E S 33 50 W ?…

A: Project of an line on North-South axis is called Latitude. While projection of line on East-West…

Q: Locate the center of mass of the homogeneous rod bent into the shape of a circular arc.

A: Given: Rod bent into circular arc

Q: Consider the beam shown in (Figure 1). Suppose that w₁ 950 N/m and w₂ = 600 N/m Figure W₁ 3m 3 m 1…

Q: Determine all bar forces using the method of Joints. Summarize answers as shown in the table below.

A: To find all bar forces using the method of Joints

Q: 1. Use LRFD. A W 10x30 unbraced column carries a factored load (P) of 250 kips. If the col- umn is…

A: NOTE : Since you have asked multiple questions, we will solve the first question for you. If you…

Q: 17.6 A solid steel shaft 3 in. in diameter and 4 ft long is fixed at one end and free at the other,…

A: Given data Diameter of shaft =3 in Length of shaft = 4 ft Axial tensile force = 50000 Lb

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f = 0.0225) of length…

Q: : A T- beam section shown in the figure below. f'c-28 Mpa, fy-420 Mpa. Calculate the design moment…

Q: Problem Direct stresses of 120 N/mm² tensile and 90 N/mm² compression exist on two perpendicular…

A: Given : Direct stresses = 120 N/mm2 ( tensile ) and 90 N/mm2 ( Compression ) Principal stress = 150…

Q: An axial load P of magnitude 560 kN is applied at a point on the x axis at a distance e = 6 mm from…

Q: Discuss the Steps for Equipment Selection as well as Equipment Utilization in a 1000 bedded…

A: Steps for Equipment Selection: 1) Determining the need: Before purchasing any equipment, the primary…

Q: Determine the magnitudes of the maximum tensile and compressive normal stresses on the transverse…

A: Given : This is a problem of solid mechanics where we have to find the magnitude of max. tensile…

Q: wo smooth cylinders are placed in the position shown. Cylinder A 1,000N and has a radius of 10cm…

Q: A bar 40 mm in diameter is subjected to a tensile force of 40,000 kg . The extension of bar measured…

Q: 1. Determine the horizontal and vertical components of the hinge supports at A and D and the…

Q: Using examples of how the concept or system has been used or can be used in buildings (new…

A: The concept of smart windows which is adopted in the new construction buildings and retrofits is…

Q: A flat bar 10 mm thick and 100 mm wide is subjected to a pull of 100 kN. One side the bar is…

A: A ) Given data : Thickness = 10 mm Width = 100 mm Pull = 100 kN E = 200 kN/mm2 and Poisson's ratio…

Q: Integration mine the deflection at midspan between A and B by

Q: 2. In a longitudinal profile, which is rotated at center lane. If the width of the road is 3.00 m,…

Q: The plan area of an old survey plotted to a scale of 10 m to 1 cm presently measures 82.5 cm². It…

A: Given data: The plan area of an old survey plotted to a scale of 10 m to 1 cm presently measure 82.5…

Q: Ex. A small stream has a cross section which can be approximated by a trapezoid. The cross-sectional…

Q: depth of 56 cm and an average velocity of 9 m/s undergoes a hydraulic jump. Determine the head loss…

Q: A beam is loaded with a distributed load as shown. Given that wo = 415 lb/ft, the equivalent…

A: Answer We can determine the location of equivalent concentrated load to the right of A by using…

Q: The following mix design information is provided to you for 1 m³ concrete. • Air content = 5% • w/cm…

A: Reference : Concrete technology, Mix design ACI 318 mix design code Given : Air content, w/c ratio,…

Q: Determine the following using the conjugate beam method: a) Slope at D b) Displacement at end A EI…

Q: Question 4 = A 6 KN force is applied at the free end of a wood (E = Fig. Q4. Neglecting the effect…

A: Given data: Modulus of elasticity, Ewood= 12 GPa The maximum compressive stress in the beam can be…

Q: A beam section is limited to a width of 250 mm, and total depth h=550 mm, and has to resist a…

Q: A student recorded the following repeated paces of a given line: 456, 448, 462, 447, 452, 455. If…

A: Given: Pace factor= 0.628m/pace

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

From A to B it is 7.5ft, from A to G it is 24ft.

F7.3 Determine the forces in members CD, HJ and CJ knowing that the loads supported by the
Pratt truss are: B = 175 lbs, D = 175 lbs, and J = 325 lbs. Indicate tension or compression.
E
F
B
C
7.5
A
H
+ panels @ 6-24 t

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the force in member BD in kN. P1 = 51 kN, P2 = 53 kN and x = 5.3 m.
Set P1 = 53 kN, P2 = 36 kN A) Determine the force in member AD and state if the member is in tension or compression B) Determine the force in member BC and state if the member is in tension or compression C) Determine the force in member BD and state if the member is in tension or compression D) Determine the force in member CD and state if the member is in tension or compression B)
Compute the force in member AB in kN. P1 = 81 kN, P2 = 60 kN and x = 7.8 m.
Determine the force in each member of the truss. P1 = 800 lb and P2 = 400lb. (Prob. P6.1/2)
Set P1 = 49 kN , P2 = 32 kN . Determine the force in member AD, and state if the member is in tension or compression. Determine the force in member BC, and state if the member is in tension or compression. Determine the force in member BD, and state if the member is in tension or compression.
From the given truss shown, compute the force in member DE. a.62.5 N (C) b.187.5 N (C) c.62.5 N (T) d.37.5 N (C)
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
1. Find the resultant of tension F and Ta. 27.6 kNb. 37.2 kNc. 33.7 kNd. 44.6 kN2. What is the angle that their resultant makes with the horizontal rod OA? a. 28 degb. 37 degc. 33 degd. 44 deg3. Find the weight, W to prevent uplift. Use a factor of safety of 2.5. a. 49.23 kNb. 42.86 kNc. 59.51 kNd. 44.72 kN
17. Determine the force in BC member of the loaded truss. a. 7.40 kN T b. 8.54 kN T c. 4.13 kN C d. 6.32 kN C
For the truss shown below is supported by a pin at A and roller at F. If it is loaded with P (kips)at joints B and E, determine the force in members AD, GH, BD, CE, and DG. P(kN) = 516
Determine the forces in members CH, AH, and CD of the loaded truss. 5 kN 5 kN 5 kN 2 kN 2 kN B 3m F 2 m 4 m 4 m BC = CD = DE =
The Channel section is used as a purlin placed on top of trusses with spacing of 4.9 m and slope 1V to 4H. The purling are supporting a total uniform load of 15 kN/m. Properties of Channel:Sx = 119 x 10^3 mm^3Sy = 87 x 10^3 mm^3 Questions:Compute the maximum bending stress if supported by sagrods at third points.