Field density testing (e.g., sand replacement method) has shown bulk density of a compacted road base to be 2.06 t/m? with a water content of 11.6%. Specific gravity of the soil grains is 2.69. Calculate the dry density, porosity, void ratio and degree of saturation.

Field density testing (e.g., sand replacement method) has shown bulk density of a compacted road base to be 2.06 t/m? with a water content of 11.6%. Specific gravity of the soil grains is 2.69. Calculate the dry density, porosity, void ratio and degree of saturation.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter11: Compressibility Of Soil

Section: Chapter Questions

Problem 11.5P

See similar textbooks

Similar questions

1. A wet sand sample has a volume of 4.64 x 10⁻⁴ and weighs 8N. After oven drying, the weight reduces to 7.5N. Calculate the water content, void ratio and degree of saturation.(use Gs = 2.7) 2. A contractor has compacted the base course for a new road and found that the mean value of the test sample shows, w = 14.6%, Gs =2.81, and γ= 18.2 KN/m³. The specification require thate ≤0.8. has the contractor complied with the specifications? 3. The moist unit weight of soil is 16.5 KN/m³. Given that the w=15% and Gs = 2.70. Find:1) dry unit weight2) porosity3) degree of saturation
A sample of soil compacted according to the standard Proct or test has a density of 2.06 g/cm³ at 100% compaction and at an optimum water content of 14%. What is the dry unit weight? What is the dry unit weight at zero air-voids? If the voids become filled with water what would be the saturated unit weight? Assume Gs = 2.67 Air Water Solids Ma + - + M st
An undisturbed sample of fine sand is tested in the laboratory and found to have a dry mass of 4.63 kg, a total volume of 0.00198 m³ and a specific gravity of 2.70. Other laboratory tests are performed to determine the maximum and minimum density of the sand. At the maximum density, it is determined that the void ratio is 0.35 at the minimum density, the void ratio is 0.95. A. Compute the void ratio of the sand. B. Compute the relative density of the undisturbed sample. C. Compute the dry density in Mg/m³.
SIZE (mm) PERCENT FINER 2.0 90.1 0.073 53.96 0.053 41.9 0.0045 25.16 0.0017 10.1 A sample of residual soil developed on shaly sandstone has the following grain-size characteristics. USING USDA, DETERMINE THE FOLLOWING AND SHOW COMPLETE SOLUTION. PLOT THE GRAPH. (ALL FINAL ANSWER IS IN 3 DECIMAL PLACES) 1. Determine the modified percentage of sand. 2. Determine the modified percentage of silt. 3. Determine the modified percentage of clay. 4. Determine the classification of soil.
EXERCICE 2 Field density testing (e.g., sand replacement method) has shown bulk density of a compacted road base to be 2.06 t/m³ with a water content of 11.6%. Specific gravity of the soil grains is 2.69. Using the two methods (Physical relations and Phases diagram); calculate the dry density, porosity, void ratio and degree of saturation.
the maximum and minimum void ratio for sand are 0.805 and 0.501 respectively . The field density test performed on the same soil has given the following result Bulk density 1.81Mg/m3 . water content 12.7% .Assume the specific gravity 2.65 and volume 1m3 . compute the dry density of solids and volume of voids ratio and relative density of sand.
d) A sample of silty clay has a mass of 126 g. Laboratory tests results give a bulk density (p») of 2.05 g/em', a specific gravity of solids (G.) of 2.71, and a moisture content (w) of 15.7%. Determine all the phase distributions and use the values to calculate the following: i) void ratio (e), ii) porosity (n), ii) degree of saturation (S), iv) dry density (pa), v) dry unit weight (ya), and vi) bulk unit weight (yhwlk)
sample of gray silty clay has a mass of 126 kg. Laboratory tests results give a moist density (ρ) of 2.05 g/cm3, a specific gravity of solids (Gs) of 2.71, and moisture content (w) of 15.7%. First determine all entries in the phase diagram. Then determine the void ratio (e), the porosity (n), the degree of saturation (S), the dry density (ρd), the dry unit weight (Ƴd), and the moist unit weight (Ƴ)
A sample of gray silty clay has a mass of 126 kg. Laboratory tests results give a moist density(ρ) of 2.05 g/cm3, a specific gravity of solids (Gs) of 2.67, and a moisture content (w) of 14.7%.First determine all entries in the phase diagram. Then determine the void ratio (e), the porosity(n), the degree of saturation (S), the dry density (ρd), the dry unit weight (γd), and the moistunit weight (γ).
1. Sand cone equipment is used to determine an in-place unit weight (field density test) on a compacted earth fill. Ottowa sand is used in the cone and is known to have a bulk density of 100 pcf. a. From the information given below, determine the in-place dry unit weight of the tested soil, and the water content. Soil sample dug from test hole wet weight = 4.62 lb Dried Weight of soil sample = 4.02 lb Weight of Ottowa Sand (Sand Cone) to fill test hole = 3.60 lb b. Determine the percentage of compaction of the tested soil if the laboratory moisture unit weight curve indicates a dry unit weight of 115 pcf and optimum moisture content of 13 percent.
Following table presents information for a fine-grained soil: Current effective stress (kPa) Current void ratio of the soil Overconsolidation Ratio (OCR) Compression index (Cc) Re-compression index (Cr) 30 0.96 7.06 0.18 0.06 Determine the void ratio of the soil at the preconsolidation pressure.
An undisturbed sample of fine sand is tested in the laboratory and found to have a dry mass of 3.23 kg, a total volume of 0.00187 m3and a specific gravity of 2.65. Other laboratory tests are performed to determine the maximum and minimum density for the sand. At the maximum density, it is determined that the void ratio is 0.38; at the minimum density, the void ratio is 0.85. Determine the relative density of the undisturbed sample.