Answered: figure 1, determine the reaction at A…

figure 1, determine the reaction at A in kN, slope of elastic curve at A in degrees, and deflection at B and D using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A cantilever beam made or square tuce (as shown below) has a length L = 1 m. The bar is required to…

Q: USE MOMENT DISTRIBUTION METHOD. From the indeterminate frame shown, find the moment at E in kNm. EI…

Q: What is the importance of Sieving in the Construction Industry? What is aggregate grading and what…

A: Sieve analysis is done to find the gradation of particles which can be further used in the design of…

Q: Given the data below: Drainage area = 405 hectares Neglect base flow TIME Hr. 0 2 4 6 8 10 12 14 16…

Q: Situation 3: A W12x22 simply supported beam carries a uniformly distributed load. The properties of…

Q: Shear stress 7 produces a shear strain y., (be- the x direction and lines in the y direction) μ…

A: Given data- shear strain γ×y =1200 μ γ×y =0.0012 γ×y…

Q: For the beam shown below, use the 'discontinuity functions' to determine a) the slope of the beam at…

Q: 2 k/ft 24ft What is FEMBA in k-ft? B Select the correct response: ₁12k 8ft 4ft

Q: Two forces are applied to the construction bracket a shown. Determine the angle which makes the…

A: GivenR=RyRx=0

Q: why are collapsible soils rarely found in areas with very wet climates?

A: Here, two questions are given. As per the guidelines, the first question has been attempted.…

Q: Q.5 A construction engineer invests a sum of $10 000 in a bank at a nominal interest rate of 16% for…

Q: 12. A 5 cm pipe is connected with the end of a cylinder having a diameter of 50 cm. There is a…

Q: 1)Explain in 5 lines why Reynolds number is used in the Moody Diagram instead of Froude number.

A: Since, more than one questions are asked hence, as per guidelines the first question is attempted.…

Q: locations Use the graphical method to constuct the shear-force and bending-moment diagrams for the…

Q: Q3: The annual rainfall was measured in the Western Desert during a period of one year, and the…

Q: Q5) A road at a constant R.L of 180.00m runs North to South. The ground East to West is level. The…

Q: Where you have to put a warning sign for checkpoint if the design speed is 100km/hr, deceleration…

A: Given data- Design speed V=100 km/hrDeceleration rate a=-3.4 m/s2Downgrade g=-2.5%Reaction time…

Q: The potential energy of a vertically raised body is the kinetic energy of a vertically falling body…

Q: Flow occurs over a spillway of constant section where depth of flow in the upstream is 1021mm, and…

A: Given data in question Depth of upstream and downstream Width To find out Horizontal force

Q: USE SLOPE DEFLECTIO METHOD. From the indeterminate frame shown, find the moment at C acting in M…

Q: A compressive load of 50 KN is applied 150 on the axis of a steel-round bar of 8 mm diameter.…

A: Given, Compressive Load, F= 50 kN Diameter of the steel-round bar= 8mm Modulus of Elasticity= 75…

Q: Q.5 A construction engineer invests a sum of $10 000 in a bank at a nominal interest rate of 16% for…

Q: A body is in equilibrium condition if each force .A coplanar, collinear forces .B collinear,…

A: Equilibrium condition - If net force (force and moment) acting on a body zero in all directions…

Q: Please help... Consider the truss system to the right. All members are two force members. There are…

Q: How far is the center of pressure below the water surface for a vertical triangular plate whose…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: QUESTION I-TRUSS [40] For the truss shown below, determine the horizontal deflection of joint B by…

Q: Angular dimensions measure the angle between. two arc O two objects O two circle O Two point O two…

A: Answer - Option e Two lines Angular dimensions measure the angle between two non parallel lines or…

Q: Determine the headloss due to friction in a 1.75-m diameter, 550-m-long pipe using Hazen-Williams…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: USE SLOPE DEFLECTIO METHOD. From the indeterminate frame shown, find the moment at C member BC, MCB,…

A: MCB= 115.24 kNm

Q: Q9) The bearing of the sides of a closed traverse ABCDEA are as follow: Side F.B B.B AB 107° 15'…

Q: Q. 2 Determine the slope at the supports of the beam shown in Fig. I using the conjugate beam…

A: Given data E = 29000 ksi I = 1000 in2

Q: 1. Find the resultant of two forces equal to 50 N and 30 N acting at an angle of 60°. [Ans. 70 N:…

A: NOTE: AS PER OUR GUIDELINES WE ARE SUPPOSED TO ANSWER ONLY FIRST THREE QUESTION

Q: Q9) The bearing of the sides of a closed traverse ABCDEA are as follow: Side F.B AB 107° 15' BC 22°…

A: GIVEN : A closed traverse Fore bearing (FB) and…

Q: In the figure below, the horizontal bar ABC is supported by a pin at A and two rods with identical…

Q: Most economical circular channel : Depth =0.938D 20=302°22'

A: let d=depth and 2θ = angle subtend with the free surface to the centyer as shownso,Area=2θ2ππR2-1…

Q: Which of the following is the most logical arrangement when describing the relationship between…

Q: An illegal connection was observed on a 300 mm diameter horizontal pipe. Upstream from the…

Q: Situation 1: A W8x31 simply supported beam carries a uniformly distributed load. The properties of…

Q: Determine the (f_z) when distance of z = 0 and the scale of force 30 N/mm

Q: For the bears shown below, determine the vertical deflection at poine B by using the virtual work…

Q: Situation 3: A W12x22 simply supported beam carries a uniformly distributed load. The properties of…

Q: A tripod plotted in a 3-D coordinate system is supporting a downward vertical load of P = 443 kN at…

A: GIVEN: A tripod plotted in a 3-D coordinate system is supporting a downward vertical load of P = 443…

Q: In a traverse, the latitudes and departures were observed to be Σ latitude = 1.45 m Σ departure =…

Q: Calculate the magnitude of the resultant force on the indicated area on the gate and the location of…

Q: cis2.turath.edu.iq A الرجاء قم بأختيار الاجابة الصحيحة س 46 | 1 درجة When can two forces be in…

Q: - Example A well pumps water at a rate of 2500 m³/day from a confined aquifer. Drawdown measurements…

A: Answer We are given Pumping rate Q = 2500 m3/day Distance to observation well r = 120 m We can…

Q: USE MOMENT DISTRIBUTION METHOD. Given the indeterminate beam, find the moment at B in span BC, MBC,…

Q: a. b. c. 120° Az 315° Az 245° Az

A: a120°Az is in 2nd coordinate:Bearing =180-120=60°so,Bearing =S 60 E

Q: Determine the reactions at the supports of the beam. Assume that support at B is a roller and EI is…

Q: Problem definition Find the maximum tension load, P, that can be applied to a W8 x 24 element…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

For the beam loaded as shown in the figure 1, determine the reaction at A in kN, slope of elastic curve at A in degrees, and deflection at B and D using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa.

a. 5m
b. 28 kN/m
c. 30 kN
ckN
0.5*b kN/m
4m
3m
3m
b kN/m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 12 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Moment Area MethodDeflection at C and D
q=3.15 kn/m , a=3.15m
F (kN)=36 L1 (m)= 37.0053 Eal (GPa)=74
sorry，what are these： Step 3 Slope deflection equation In section AB MAB= MFAB+22EIL2θA+θB-3δLMAB= -12.5+4EI5θB MBA= 12.5+4EI52θB In section BC MBC= 0+2EI52θB+θC MCB= 2EI5θB+2θC In section CD MCD= -16.67+4EI52θC MDC= 16.67+4EI5θC arrow_forward Step 4 Equilibrium equations Equilibrium equations MBA+MBC= 0 -(i)MCB+MCD= 0 -(ii) Now, From i12.5+8EIθB5+4EIθB5+2EIθC5= 0EIθB125+EIθC25 = -12.5 -(iii) From ii2EIθB5+4EIθC5+-16.67+8EIθC5=02EIθB5+EIθC125= 16.67 iv Solving equations (iii) and (iv), we get EIθB= -6.548EIθC = 8.037
Qe.7.
Use fbd rectilinear motion
24.5m is the right ans.
To prevent the ladder weighing 600N from sliding down, the man exerts a horizontal force at C. The coefficient of friction at A= 0.2 while surface B is frictionless Find the vertical reaction at Aa. 600N c. 500Nb. 700N d. 800NFind the horizon reaction at Aa. 150N c. 210Nb. 180N d. 120NFind the horizon force exerted by the man at Ca. 533.3N c. 333.3Nb. 667.7N d. 767.6N
find moment at point D, P=15kN
0 a 2178 kN O b. 3726 kN 1| select one: WG o weiox92
Answer using moment distribution method. Use second picture as guide W= 25P1 = 25P2 = 25
Determine the horizontal force Q applied to block B that would cause the system to impend its motion to the left. (All contact surfaces have the same angle of friction of 11.31 degrees except the horizontal surface beneath block B with 16.7°)