Figure 2.3 shows the circuit diagram of a typical npn BJT common emitter amplifier. The values of RB1-30 kOhm, RB2=10.XY kOhm, Rc-3.XY kOhm, Ic=2.XY mA and Vcc=24 V. If the transistor current gain ß = 50 determine using the full analysis and assuming VBE = 0.7 V the value of RE, hence identify the location of the Q-point (Ic, VCE, IB and VBE). Now sketch the AC circuit model of this amplifier and determine the value of the ac open circuit voltage gain Av and the ac short circuit current gain Ai. (Assume that Vth = 26 mV). Vin R81 Cin RB2 www Rc VB RE + Vcc Vc Cout VE ww HT Vout Ce lout x=1 y=7

Figure 2.3 shows the circuit diagram of a typical npn BJT common emitter amplifier. The values of RB1-30 kOhm, RB2=10.XY kOhm, Rc-3.XY kOhm, Ic=2.XY mA and Vcc=24 V. If the transistor current gain ß = 50 determine using the full analysis and assuming VBE = 0.7 V the value of RE, hence identify the location of the Q-point (Ic, VCE, IB and VBE). Now sketch the AC circuit model of this amplifier and determine the value of the ac open circuit voltage gain Av and the ac short circuit current gain Ai. (Assume that Vth = 26 mV). Vin R81 Cin RB2 www Rc VB RE + Vcc Vc Cout VE ww HT Vout Ce lout x=1 y=7

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Prepare the comparison table for the Power semiconductor devices 1)Integrated gate-commutated thyristor (IGCT) 2) Static induction thyristor (SITH) 3)Static induction transistor (SIT) .(Symbol, VI characteristics, Application, Voltage & Current rating)
The DC load line and point Q of the circuit in figure (a) are shown in figure (b).For the BJT, silicon, β = 120. Find the values of RE, R1, and R2 such that the circuit has stable polarization.
The dc load line on a family of collector characteristic curves of transistor shows the........ Choose correct answer : A) All operating regions B) cut-off region only C) active region only D) saturation region only
Emitter-Bias Configuration1. What happen to the collector voltage, if the emitter resistor is removed and connect directly the emitter junction to the ground? 2. What happen to the collector voltage if the 39kΩ resistor is disconnected (open)?3. What is the purpose of a 1kΩ emitter resistor?
What are the differences between the working principles of diodes and BJT transistors? Explain pls.
17)The region in the drain characteristics of FET where the drain current (ID) is linear to the drain voltage (VDS) is saturation region breakdown region breakdown region ohmic region
) Determine the reading obtained withaDC voltmeter at RB when the switch is set at point B. b) Determine the reading at thesame RBusing ½ wave and Full wave rectifier AC meter respectively when the switch is set at point A. Given that Ifs = 100-µA and set at 10-V dc or rms range.
Thanks for the help This is about the integrated fabrication process for microelectronic devices for a bipolar n-p-n transistor; . Please work out the fabrication process flow. In each step of fabrication process, please illustrate the cross-section of the structure and indicate the material of each layer, the patterning of each layer and the process used.
How does the construction of a transistor differ from the construction of a PN junction diode? What are the two types of transistors? What are the three parts of a transistor called? Draw and label the schematic symbols for an NPN and a PNP transistor. What are transistors used for? How are transistors classified? What symbols are used to identify transistors? What purposes does the packaging of a transistor serve? How are transistor packages labeled? What are the basic functions of a transistor? What is the proper method for biasing a transistor? What is the difference between biasing an NPN and a PNP transistor? What is the barrier voltage for a germanium and a silicon transistor? What is the difference between the collector-base junction and the emitter- base junction bias voltages? What may cause a transistor to fail? What are two methods of testing a transistor? When using an ohmmeter, what should the results be for an NPN transistor? What are the two…
Prepare the comparison table for the Power semiconductor devices 1)Integrated gate-commutated thyristor (IGCT) 2) Static induction thyristor (SITH) 3)Static induction transistor (SIT) .(Symbol, VI characteristics,
circuit shown in the figure, Kn = 2mA / V2, VIN = 0.7V for Mi mosfeti. So, what kind of relationship should there be between R1 and R2 resistance for mosfet to work at saturation?
Describe the basic principle of operation of a bipolar junction transistor. Include explanation for the following : When minority carriers flow across the transistor Why the collector current is almost unaffected by the collector potential