Figure shows a typical microwave receiver used in satellite commuối colionfigure of the receiver i the overallCalculate i) theoverall noiseequivalentof the receives Assume the ambient temposaturetempe ratureT=17°C-Te -SK F2= Sd Bo64 F3= 12dBor 16Mixer andSF a mplifiesAntennaTo detectorMasterAmpTWT%3DG, = 3odB 2= 20dB Gg=40DBOFDr 100008 LO0101000

The unwanted part of signal is called noise. Noise is equal to standard deviation of signal. Noise…

Figure shows a typical microwave receiver used in Calculate li) the overall hoise figure of the raceiver (i the overall equivalent temperature of the receiver Assume the ambient temposatura T=17°C- Te-SK F2= Sd Bo64 F3=12dBor 16 Mixer and SF ampli fies Antenna To detector Mastes Amp TWT G = BodB 2= 2odB Ga-40d Bor %3D or LO0 L01000

Figure shows a typical microwave receiver used in Calculate li) the overall hoise figure of the raceiver (i the overall equivalent temperature of the receiver Assume the ambient temposatura T=17°C- Te-SK F2= Sd Bo64 F3=12dBor 16 Mixer and SF ampli fies Antenna To detector Mastes Amp TWT G = BodB 2= 2odB Ga-40d Bor %3D or LO0 L01000

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the microwave system given in the figure Find the attenuation between the input and the charge. Vi=9 volt, f= 10 MHz, γ=6+ j0,3, R= 47 ohm, c= 0,1 nF lesson: communication systems
As a technician, you are responsible for the construction of a 10km optical communication link between Pelonomi Hospital and National Hospital in Bloemfontein. The following link specifications are available:Transmitter output power: 15mWCommercially available optical cable length: 2kmOptical cable attenuation: 1.2dB/kmSplice attenuation: 0.1dB/kmLight transmitter-to-cable loss: 1.5dBCable-to-photo detector loss: 1.5dBSafety margin: 7dB Determine the minimum receiver sensitivity in microwatts needed to reliably detect a transmitted signal.
At a certain time, the maximum usable frequency (MUF) for transmission at an angle of incidence of 75° is 20MHz. A) What is the critical frequency in MHz? (Use two decimal places for the final answer) B) What will be the optimum working frequency (OWF) in MHz? (Use two decimal places for the final answer)
The radio path (f = 900 MHz) between a mobile phone and the base station has a loss of 30 dB in addition to the free space loss. The base station measures the level of the signal transmitted by the phone, and it sends the phone a command to set the transmit power to a level, which gives a received power level of-90 dBm. The antenna gain of the phone is 2 dB and the receive gain of the base station antenna is 7 dB. The distance between the phone and the base station is 500 m. What will be the transmit power level of the phone?
A satellite at an altitude of 37654 km transmits a signal of 17 GHz to a ground station directly below it. The following data is given. • Total atmospheric losses = 40dB • Transmit antenna gain = 55dBi • Receiver antenna gain = 60dBi • Signal to noise ratio of received signal = 6dB • Receiver signal noise power = 25pW • Receiver sensitivity = -90dBW I. Calculate the power transmitted. II. Find the Fade Margin for the link and comment on your result.
Derive the formula for maximum usable frequency and skip distance assuming earth is perfectly flat.
a. A microwave link consists of repeaters at 40 km intervals. What must be the minimum height of transmitting and receiving antennas above ground level (given that they are the same) to ensure line-of-sight condition? b. Calculate the radio horizon if the height of the transmitting and receiving antenna are 100 ft and 150 ft respectively. Use k=2/3.
EMT by sadiku-chapter 13-antenna problem no 20.-ASAP
Multiple Choice directions: Circle the letter of the answers that best answer the question. 16. A microwave transmission line used to minimize noise and crosstalks.a. Striplineb. Hard line cablec. Waveguided. Microstrip17. The major difference between a low frequency transistors and microwave types is/are.a. B & Cb. Packagingc. Materiald. Internal geometry18. Which of the following band belongs to the millimeter wavesa. Cb. Kuc. Ud. L Note: Explanation is not needed just provide the correct answers for each number.
Multiple Choice directions: Circle the letter of the answers that best answer the question. 19. Overcrowding in the frequency spectrum is prevalent in which area of the spectrum?a. EHFb. UHFc. SHFd. VHF20. What materials is used as the ground plane of the microstrip?a. Teflonb. GaAsc. Fiberglassd. Copper21. Which of the following is not a microwave tube?a. Klystronb. TWTc. Magnetrond. Cathode- Ray tube
19. Overcrowding in the frequency spectrum is prevalent in which area of the spectrum?a. EHFb. UHFc. SHFd. VHF20. What materials is used as the ground plane of the microstrip?a. Teflonb. GaAsc. Fiberglassd. Copper21. Which of the following is not a microwave tube?a. Klystronb. TWTc. Magnetrond. Cathode- Ray tube Note: Explanation is not needed just provide the correct answers for each number.
A station transmits with 50 Watts transmitter power and 6 dB antenna. A) What is the effective isotropic radiate power (EIRP) in W? (Use two decimal places for the final answer) B) What is the power density (mW/m^2) in a point that is 100 m away from the station? (Use two decimal places for the final answer)