Fill the following blanks with the correct words. The parallel adder performs operation --------------- than the serial adder

Q: Use ONLY 1-to-4 demultiplexers to implement a 1-to-8 demultiplexer. Avoid any redundancy by clearly…

A:

Q: How can I implement a full subtractor using a 3x8 decoder.

A:

Q: In analog to digital conversion, the analog information is represented by a series of 1s and 0s.…

A: Analog signal is represented by continuous time  Where as digital signal is represented by 0s and…

Q: In parallel communication (select all correct answers)a) All communications occurs one bit at a time…

A: In serial communication, the communication takes place via a single wire or connection and one bit…

Q: H\W: Assuming the SP=1236, Ax=24B6, DI= 85c2 and Dx=5f93, show the content of the stack and the…

A: Given, SP = 1236H AX = 24B6H DI = 85C2H DX = 5F93H Following Instruction to execute, ADD AX, SP PUSH…

Q: Exercise : Draw the block diagram of a 4 bit parallel adder using a combination of Half Adders and…

A: Draw the block diagram of a 4 bit parallel adder using a combination of Half Adders and Full Adders.

Q: 5. When two words are multiplied (one in BX), the most significant word of result will be in а. ВХ,…

A: The explanation is as follows.

Q: Duty: design a hand counter according to the following order from left to right 4, 5, 0, 1, 3, 7…

A: SEQUENTIAL LOGIC CIRCUITS: Sequential Logic circuits, unlike Combinational Logic circuits, have some…

Q: Error: the deviation of the measured value from the

A: This question belongs to measurements and instrumentations . It is based on the concept of error .…

Q: Q4/ The minimum Carry save Adder using to add 15 numbers are

A: The explanation is as follows.

Q: 5. Design the Full Adder circuit using: i) only Half Adders and a OR gate, ii) only a single 3x8…

A:

Q: The function HOLD ON is used to avoid erase of the first figure by the second one. O FALSE TRUE

A: No. Given statement is wrong.

Q: Which of these registers are not used to store the EA in the Register indirect addressing a. BX b.…

A: The correct option is SP(STACK POINTER).

Q: A-Find the excess-3 code of 345), B- convert the decimal number (53), to gray code

A: a) Excess-3 code is non-weighted code which is used to express decimal numbers. It is a self…

Q: Add the signed numbers (-9,286) + (-801) in binary using 10’s complement to represent negative…

A: 10's complement addition

Q: Draw the circuit of serial in serial out and parallel in parallel out shift register using gates if…

A:

Q: recombination? Hangisi rekombinasyon türüdür? A) Işıma

A:

Q: The operation of PUSH AX instruction is : (AL+1) <-- ((SP)); (AH+2) <-- ((SP) + 1); (SP) -- (SP) + 2…

A: This is simple question based on microprocessor

Q: What are different coding style in Verilog

A: In this question we have to write the different coding style in verilog

Q: For a Half Adder, the number of inputs is and the number of outputs is

A: Half adder is a combinational circuit. It is designed using EX-OR Gate and AND gate.

Q: Q14. For the parallel adder in Figure 01, determine the complete sum by analysis of the logical…

A:

Q: : To Design parallel adder to add 5 numbers ( 4-bit) must using 2(4-bit parallel adder)+ 2 (8-bit…

A: Answer: 2(4-bit parallel adder) + 2(8-bit parallel adder)   Explanation: a. The two pairs of input…

Q: Fill in the blank to supply the missing/s words to complete the sentence. Electrical that comes…

A: Mostly power station produces the electricity in AC form it is because the distribution of the…

Q: Implement a full adder with two 4 × 1 multiplexers.

A: Implementation of Full adder with two 4:1 Multiplexers is explained below: Multiplexer : Multiplexer…

Q: Write a program to PUSH R0, R1, and R3 of Bank 0 onto the stack and POP them back into R5,R6, and R7…

A: The  program to PUSH R0, R1, and R3 of Bank 0 onto the stack is written as: PUSH 0 PUSH 1 PUSH 3…

Q: Show me very step even when simplifying

A:

Q: A standard second order system has

A: Open Loop System-A system having a input in the system which does not depends on the system output.…

Q: The JFET terminals that are connected to thechannel are the A. Gate and sourceb. B. Drain and…

A: Drain and source are the  JFET terminals that are connected to the channel.…

Q: Q.5) Design inside of the black box given below. The black box should do the function X1(x2+x3) = y.…

A:

Q: What does a full adder consist of ?

A:

Q: When no key is pressed the input port (Port B) will read _____.  A) 0000 B B) 4567 C) 1111 B D)…

A: when no key is pressed all input of port B will connected to vcc through resistors vcc means logic…

Q: Section B: 1. Design a 5-bit divider to divide the 6-bit by two using a shifter circuit.

A:

Q: Your output port is connected to 8 LEDs.  You wish to turn on only the first, least significant LED,…

A: In this question,   We need to determine the Hex code if wish to turn on only the first, least…

Q: Which of the following is a * ?comparison operator & O And O The Select Case statement must end with…

A:

Q: TURKÇE RUSÇA Draw a 1 to 2 DEMULTIPLEXER circuit with and gates. Geri bildirim

A:

Q: Explain why a serial adder is a sequential circuit.

A: Sequential circuits are circuits that contain memory elements such that their output is dependent on…

Q: Implement Full adder using HA and minimum number of external gate

A: The circuit whose output depend only on the present input are called combinational circuit. The…

Q: QUESTION 4 When no key is pressed the input port (Port B) will read Port A (output) DO 4 D1 8. D2 A…

A: The logic circuit is shown below:  When no button is pressed, the inputs at the port will be at…

Q: Question 14 In order to avoid the indeterminate state of the SR latch, the JK latch was designed the…

A: So the correct option is JK latch means a part

Q: IC 74LS83 is a a.4 to 1 multiplexer b. 5 bit parallel adder c.4 bit parallel adder d. X - OR Gate

A: The IC 74LS83  is a high speed 4-bit fuller Adder .

Q: Write addressing mode that used the following instructions? 1- MOV [SI], CX 2- MOV AX, [1D20] 3-…

A: MOV [SI], CX; Indexed addressing mode In the indexed addressing modes offset of the operand is…

Q: The maximum electrical trade size of intermediate

A:

Q: H.W: For a five-bit resistive divider, determine: a) The weight assigned to the LSB and also the…

A:

Q: How does an XOR gate schematic symbol differ from an OR gate symbol? Select the correct response.:…

A: In this questions,  We need to choose the correct options What is difference between OR gate and XOR…

Q: Determine the base of the numbers for the following operation to be correct 54/4=

A: The solution can be achieved as follows.

Q: With the help off block diagrams realize 16:1 multiplexer using two 4:1 multiplexer and one 2:1…

A:

Q: 6. Realize a full adder using a 3-to-8 line decoder and two OR gates.

A:

Q: Identify the correct statement that relates to XOR gate O a. The output is high when the inputs are…

A: To select correct answer from the option

Q: By Using de Morgan's law show the bubbling and changes that happen to convert the circuit (A•B•C)…

A: