● ● Filtration ● ● Assume flow of the filter is V₁ = 7 m³/h·m². Calculate the total area of the filter bed Qavg Vf Assume that a total of 10 filter units were used => Find the area of one filter unit. Assume width of one filter unit is 4.5 m and calculate the length. I ne amount of packwasning water should be less than or equal to the 5% rate of the filtered water. Rate of wash water = ? V backwash = ?

● ● Filtration ● ● Assume flow of the filter is V₁ = 7 m³/h·m². Calculate the total area of the filter bed Qavg Vf Assume that a total of 10 filter units were used => Find the area of one filter unit. Assume width of one filter unit is 4.5 m and calculate the length. I ne amount of packwasning water should be less than or equal to the 5% rate of the filtered water. Rate of wash water = ? V backwash = ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the design of granular media filters for a water treatment plant with a design flow of 40 MGD. For a filtration hydraulic loading of 5 gpm/ft2 determine the total filter area required for filtration (in square ft). Next, select the number of parallel filters needed, and their length and width (even foot increments), if each filter is square with area of 400 square feet. You choose a filter consisting of 36 inches of sand with an ES of 0.55 mm. The porosity is 0.4. Determine the superficial filtration velocity and the pore velocities in the sand layer. Calculate the detention time (in minutes) through the entire depth of the filter Calculate the clean bed head loss (in feet) for the filter using the Carmen-Kozeny equation. Assume a water temperature of 68 ºF and the design hydraulic loading rate. Use the media effective size for media diameter in the calculation. Estimate the filtration efficiency for a particle that is 4 microns in diameter.
A WTP is designed to treat 48,000 m3 / day. For filtration 12 RSFs are used, each filter is designed with 2 troughs of a square cross - sectional area. The filtration rate is 160 m / day and the backwash rate is 864 m / day. Find 1) Dimensions of each filter, Land W (m) with or without washing? Also filter depth? 2) Dimensions of each trough, y and b (m) and gullet? 3) Volume of water (m3) to wash 2 filters at the same time for 5 minutes?
A rapid sand filter is required to treat the flow of 0.50 m³/sec. The filtration rate is 120 m³ per day per m² of filter area. Each filter is washed for 5 minutes every 24 hours. at a wash rate of 15 mm per second per m² of filter area. The filter remains out of operation for a total interval of 30 minutes per day. Calculate the minimum number of filters required if the area of each filter is 50 m².
A filter press with an effective filtering area between 350m^2 operates constantly maintaining a pressure difference of 35000Pa. The viscosity of the fluid (water with milk solids) was measured at 0.002Kg/Ms and the following data is obtained: (Data image) Considering that the density of milk solids on average is 200Kg/m^2, calculate filtration velocity at t=120m . I need help with this one plz
A filter press with an effective filtering area between 350m^2 operates constantly maintaining a pressure difference of 35000Pa. The viscosity of the fluid (water with milk solids) was measured at 0.002Kg/Ms and the following data is obtained: (Data image) Considering that the density of milk solids on average is 200Kg/m^2, calculate filtration velocity at t=120m
Exercise (51 A system of pipe drains of (0.2m in diameter) are used to drainage area, the drains are located (1.8m) below ground surface. The impervious layer about 6.8m from ground surface, k = 1.0 m / day. The successive irrigations are every 20 days, deep percolation losses toward water table (WT) are 40mm / irrigation. Determine the spacing between drains (1) To maintain WT level of 0.8m. 2) To maintain WT level
Please answer 4 and 5 Consider the design of granular media filters for a water treatment plant with a design flow of 40 MGD. For a filtration hydraulic loading of 5 gpm/ft2 determine the total filter area required for filtration (in square ft). Next, select the number of parallel filters needed, and their length and width (even foot increments), if each filter is square with area of 400 square feet. You choose a filter consisting of 36 inches of sand with an ES of 0.55 mm. The porosity is 0.4. Determine the superficial filtration velocity and the pore velocities in the sand layer. Calculate the detention time (in minutes) through the entire depth of the filter Calculate the clean bed head loss (in feet) for the filter using the Carmen-Kozeny equation. Assume a water temperature of 68 ºF and the design hydraulic loading rate. Use the media effective size for media diameter in the calculation. Estimate the filtration efficiency for a particle that is 4 microns in diameter.
Calculate dimensions and power requirements for Flocculator to treat 30000 m3/d wastewater flow. Flocculator should be 4 m deep and maximum 10 m wide.Use following information:μ = 1.003*10-3 Ns/m2 ρ = 999.1 kg/ m3 CD = 1.8 G*t = 3.5*104 Vp = 0.67 m/s 4paddle,4board configurations
in a design of a portable sprinkler system, consumption rate= 8 mm/day, efficiency of irrigation = 80%. Net depth of irrigation (NDI) = 64 mm, and the HRS= 11 hours, the application rate is
Irrigation and drainage, i need solutions in 15 minutes please. MCQ/Using Dupuit formula find the drain spacing for the following data 1- Coefficient of permeability = 0.3 m/day 2- Recharge required to be removed per unit area q = 0.84 cm per day 3- Impermeable layer depth below ground surface = 5 m 4-Distance from ground surface to the centerline of the drain = 1.5 m 5-The water table should be 0.6 m below the ground level. The answer is * A-22.50 m B-34.20 m C-31.90 m D-44.70 m
Water at T� = 25∘C∘C is drawn from an underground detention tank and discharged into a drain using a 9-mm-long pipe and pump (Figure 1). The pipe has a diameter of 100 mmmm and a friction factor of f� = 0.02. The atmospheric pressure is 101.3 kPakPa. The velocity through the pipe is 4 m/sm/s and hℎ = 2 mm. Neglect minor losses. Determine the available NPSH. Express your answer using three significant figures. Determine the required NPSH. Use the pump performance curves shown above. Express your answer using two significant figures.
12.28 Determine the NRC BOD removal efficiency for a two stage trickling filter plant based on the following: primary clarification with 35% BOD reduction, first stage filters loaded at 80 lb/1000ft3/day, intermediate settling, second stage filters sized identical to the first stage units, an operating recirculation ration of 1.0 for all the filters, final clarification of the effluent, and a waste water temperature of 18 c