Find the block shear strength of a tension member as shown in figure below. The steel is of grade Fe410. a 50 115 18 mm dia hole C b ISA 80 × 50 × 8 45 35

Q: Compute the wind load acting on the short wall of the building based on simplified (envelope) method

A: Answer Calculation of wind load acting on the short wall of the building based on simplified…

Q: Results of traffic flow studies on a highway indicate that the flow-density relationship can be…

A: Answer We are given a speed-density model Speed (mi/hr) Density(veh/mi) 56 19 54 24 45 44…

Q: Example 5 Calculate the live load of a R.C.C. slab Size of the Slab is 3.0mt by 5.0 mt., Thickness…

A: Following are the given information. Type of building = School Length of slab, L=5.0 m Width of…

Q: The strain components at a point in a body are given as: Exx = 12 ms, Eyy = 4 ms, and engineering…

A: Given: εxx=12 ms εyy=4ms γxy=-6 ms To find: a) The magnitude of the principal strains b) The angle…

Q: A closely-coiled helical spring of round steel wire 5 mm in diameter having 12 complete coils of 50…

A: Given - Diameter,d = 5 mm Mean diameter = 50 mm No. of coils, n = 12 Axial load, P = 100N Modulus of…

Q: (c) A shaft composed of segments AC, CD and DB is fastened to rigid supports and loaded as shown in…

A:

Q: Determine the slope correction for a length of 50 m along the gradient of 1 in 30 ?

A: Given. Length,l= 50mGradient=1 in 30Determine the slope correction ?

Q: A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If…

A: Given data- Length L=2 m, Width b=20 mm, Thickness t=15 mm, Tensile load P=30 kN, Poisson's ratio…

Q: 600 m³/day of water is to be obtained from a proposed infiltration gallery, which is placed at 6 m…

A:

Q: A 12 KN-m torque is applied to the free end of the 6-m steel shaft. The angle rotation of the shaft…

A:

Q: Problem 4 Determine the design tensile strength Pn of the MC18x58 channel shown based on yielding…

A:

Q: A vertical bar screen is constructed of 20-mm diameter bars that have a clear spacing of 25 mm.…

A: Given data: Diameter of bars=20mm Clear spacing between bars=25mm Approach velocity, Va=1 m/s It is…

Q: A partially saturated sample of soil has a unit weight of 2.0 g/cm³ and specific gravity of soil…

A: Given: Soil unit weight, γt = 2 g/cm3 Specific gravity of soil particle, G = 2.6 Moisture content in…

Q: The pipe in figure discharges water from an upper tank to a lower tank as shown. The pipe consists…

A: Length of pipe=500ft Diameter of pipe=6 in To find discharge

Q: Determine the tensile strength of an angle section ISA 150 x 115 x 8 which is connected to gusset…

A:

Q: Find the seepage velocity through soil 1 if the average velocity is 0.0073 meters per second. Use 3…

A: Answer) To calculate the seepage velocity through soil 1, we can use Darcy's law, which states that…

Q: In the following problem, draw moment and load diagram corresponding to the given shear diagrams.…

A:

Q: 1. Observers stationed at two sections XX and YY, 500 ft apart on a highway, record the arrival…

A: Given: L = 500 ft T = 15 sec Vehicle Section XX Section YY A To To+7.58 sec B To+3 sec…

Q: A soil has liquid limit 65%, plastic limit of 30% and shrinkage limit of 25%, and it has natural…

A:

Q: Make the Hyetogram from the Pluviometric band. Indicate the 20, 30, and 60 min of greatest…

A: Given:-  Each horizontal stripe = 1 mm Each vertical line = 1 h To determine:- Make the Hyetogram…

Q: How much bleaching powder is needed to chlorinate 5000l of water whose chlorine demand is 2 mg/l,…

A: Given: Quantity of water to chlorinate = 5000 l Chlorine demand = 2 mg/l Bleaching powder has 25 %…

Q: Determine the moment of each of the three forces about point B.

A:

Q: The window is held open by cable AB. Determine the length of the cable and express the 30-N forces…

A:

Q: ⒸCOMPUTE FOR SX, ZX AND SHAPE FACTOR 3in 3/4 in. 3in. 5/8 in. 5/8 in. 1) 12"

A:

Q: retaining wall with measurements A 30m x 12m x 6m was constructed with bricks of dimensions 8cm ×…

A:

Q: The frame is subjected to a concentrated force of F= 1055 lb and a uniform distributed load of…

A:

Q: Write a one page report discussing the building blocks or elements of design.

A: The question has asked to discuss the building blocks and elements to design.  Major parts of a…

Q: 3. check the capacity of the shear connection. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi…

A: Answer  We are given  weld size = 5/16 in weld length = 13 in  two sides FEXX = 70 ksi Calculations…

Q: Compute the hydraulic radius for a circular drain pipe running half full if its inside diameter is…

A:

Q: A soil having the average properties, bulk unit weight = 19 kN/m³; angle of internal friction = 25°…

A: Given- Bulk unit weight =19 kN/m3 Cohesion C=15 kPa, It is needed to find the critical height.

Q: *4-36. The composite bar consists of a 20-1 A-36 steel segment AB and 50-mm-diamet C83400 end…

A:

Q: The cantilever beam is loaded with Pupward concentrated load acting at distance s from the free- end…

A: Answer We are given distributed load intensity W = -7x + 63 At x = 0(free end) we get W = -7(0)+ 63…

Q: Problem No. 1 A circular foundation 2 m in diameter is shown in Figure. A normally consolidated clay…

A:

Q: A X - L=16.04 ft -w=3.8 kip/ft Wo B 12/200 Determine the shear and moment as functions of x, and…

A:

Q: For a flow in a rectangular channel of width 5 m and depth of flow of 2.3 m the Darcy Weisbach…

A:

Q: *3-8. Determine the force in cables AB and AC necessary to support the 12-kg traffic light. Prob.…

A:

Q: Instructions: Compute the reaction components at A and G and then find the internal forces. Complete…

A: RA+RG=360+600 RA+RG=960 Taking moment about support G, RA×66 =360×46+600×13 RA=369.1 RG=960-369.1…

Q: . A tensile reinforced beam has b=300mm, d-500mm to the centroid of the bars, which are placed in…

A: Given:- Width, b=300 mmEffective depth, d=500 mmfy=415 MPafc'=35 MPaNumber of bars=5Diamter of…

Q: Undisturbed soil sample was collected from the field in steel Shelby tubes for laboratory…

A:

Q: 30 mm A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and…

A: Given Data Find the bending stress at point A, B and C.

Q: A large billboard is to be constructed by the side of a two-lane road, on the inside of a horizontal…

A: A superelevation occurs when the pavement rotates as it approaches and passes through a horizontal…

Q: 6. The strength of a fully matured concrete sample is 500 kg/cm². When cured at an average…

A: Given data- A fully matured concrete sample- Strength=500 kg/cm2, Average temperature=20oC in day…

Q: For a horizontal curve, the radius of a circular curve is obtained as 300 m with the desig speed as…

A: Given: The radius of a circular curve, R = 300 m. Speed, V = 15 m/s Jerk, C = 0.75 m/s3.

Q: What will be the corrected staff reading at a point A if the staff reading taken from an instrument…

A: Given data- Staff reading = 3.5 m, Distance D=2 km, To Find- The value of the corrected staff…

Q: Problem 2. The framing plan shown has the following loadings: Unit weight of 100mm slab thickness:…

A: Given: Slab thickness, t = 100 mm unit weight of the concrete, γ= 23.5 kN/m3 Ceiling load = 1.8 kPa…

Q: 4- For a storm of 3 hrs duration, the rainfall rates as follows: 60-90 4.8 If the surface run off is…

A:

Q: A canal supplies water to an area growing wheat over 100 hectares. The duration between the first…

A: Given data- Area A=100 ha, Time period B2=120 days, Total depth of water ∆2=35 cm, kor depth- ∆1=12…

Q: The unit weight of a compacted sand backfill was determined by field measurement to be 1738 kg/m³.…

A:

Q: The roof truss serves to support a crane rail which is attached to the bottom cord of the truss as…

A:

Q: What is the gel space ratio of a sample of concrete, if the concrete is made with the 600g of cement…

A:

Properties of materials

A property of a material describes its characteristics and distinguishes it from the others. The material properties are described it in terms of its hardness, color, appearances, and so on. The material properties generally depend on the type of material, or whether it is a metal or an alloy. There are different kinds of material properties such as mechanical properties, thermal properties, physical properties, and chemical properties. Chemical properties describe the material in terms of a chemical change. The mechanical properties come into existence when the material is acted upon by an external load. Thermal properties are associated with the temperature of the material and specific heat.