3.2.A distributary head regulator for a rectangular canal which take off water frommain canal with the following data:Main canalDistributary canalQ=22m /secMax.discharge=3m"/secBed level-49.51mBed level-50.6mWater level=51.9mWater level=51.8mDepth of flow-2.39mDepth of water=1.2mFlood level=52.14mBed width-2mBed width=5mIf the silt factor is 1,the horizontal length of floor-13.2m,U/S and D/S ends with 1.2mdepth of cut off.a) Find the clear water way of distributary regulator(cd=0.82)b)Check the depth of D/S cut off.

Given data: Side slope m=1.1 m = 1…

Answered: )Find the clear water way of…

Engineering

Civil Engineering

)Find the clear water way of distributary regulator(cd-0.82) )Check the depth of D/S cut off.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The water is passed through a steel pipe with a diameter of 23 cm (rough height0.046 mm) out of the reservoir. calculate(a) flow (discharge), (b) enable water flow to completeEntrance of full developmentlength).
Plz, solve the two parts of this question. Hydraulics. Reg.No: 5395 Question. a). A lined rectangular channel (n = 0.015) has a flow depth of 2m and a bed slope of 1 in 1600. Width of a channel is equal to the last digit of your registration number in meters. Retaining the rectangular shape and same total perimeter of a lining, DISCOVER the change in discharge for a most efficient x-section of a channel, if the bed slope, channel width and manning’s n remain same. b).DISCUSS the critical depth, normal depth and hydraulic depth of flow for subcritical and supercritical flow in open channel.
Consider inviscid stagnation flow, ψ =Kxy (see Fig. 8.19b),superimposed with a source at the origin of strength m. Plotthe resulting streamlines in the upper half-plane, using thelength scale a =(m/K)1/2. Give a physical interpretation ofthe flow pattern.
Problem 7 - 64 Determine the flow in each pipe in the figure shown and the elevation of reservoir C if the inflow to reservoir A is 515 Lit/sec. Problem 7-64 with the following conditions: - inflow at reservoir A = 600 Ips - roughness coefficient for all pipes = 0.05 - elevation B = 92m
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. Include minor losses. (DO NOT ROUND OFF)
Calculate the uniform water depth in meters (m) of an open channel flow to convey Q=10 m3/sec discharge with manning coefficient n=0.014, channel slope So=0.0004, and channel width B=4m
A trapezoidal channel has a bottom width of 5.0m and its sideslopes at an angle of 45o. If the depth of flow is 2.0 m calculatethe area of flow A, the wetted perimeter P, and the hydraulicradius R. If the flow is expected to be critical calculate thedischarge in the channel.
Find the critical depth in the triangular channel. Velocity = 2.5m/s depth= 1.8m side slopes 1V:2H (m=2) Identiify the type of flow. Please show hand calculations and explain any steps, thank you !
Please answer all. I will rate. A discharge of 1.90 m3/s flows on an open channel with a slope of 0.0062 if the coefficient of roughness is 0.0012, compute the depth (in m) of the channel for optimum discharge using Semi-circular section Choices: 0.36, 1.36, 1.63, 0.63 Rectangular section Choices: 0.58, 1.85, 0.85, 1.58 Triangular section Choices: 1.28, 0.82, 1.82, 0.28
Three reservoirs A, B, and C are connected by a pipe system with a common junction at D. The elevation of A and č are 200 m and 178 m respectively. Reservoir B is higher than that of C with an inflow of 0.6 m³/s. The properties of pipes are as follows; from A to D, L = 1200 m, đia. = 800 mm, f = 0.0158; from D to B; L = 450 m, dia. = 600 mm, f = 0.0168; from D to C; L = 1000 m, dia. = 400 mm, f = 0.0168. 5. Determine the discharge in the pipe connected to reservoir C.a. 2.50 m/sec b. 1.50 m/sec c. 0.36 m/sec d. 0.61 m?/sec
Three reservoirs A, B, and C are connected by a pipe system with a common junction at D. The elevation of A and č are 200 m and 178 m respectively. Reservoir B is higher than that of C with an inflow of 0.6 m³/s. The properties of pipes are as follows; from A to D, L = 1200 m, đia. = 800 mm, f = 0.0158; from D to B; L = 450 m, dia. = 600 mm, f = 0.0168; from D to C; L = 1000 m, dia. = 400 mm, f = 0.0168.4. Determine the discharge in the pipe connected to reservoir A. a. 0.45 m/secb. 1.014 m/sec c. 0.96 m/sec d. 0.31 m/sec
*hydraulics *use handwritten A rectangular channel 5.50 m wide and 1.30 m deep is laid on a uniform slope of 0.002. The roughness coefficient of the channel is 0.013. 1.) Which of the following most nearly gives the rate of flow in the channel in m^3/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 2.) Which of the following most nearly gives the saving’s in lining per meter length of channel that could have been offered by using the most efficient rectangular section but adhering to the same flow capacity and slope in m^2/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 3.) Which of the following most nearly gives the savings in earth excavation per meter length of channel that could have been offered by using the most efficient rectangular Section but adhering to the same flow capacity and slope in m^3/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67