Find the farce f the brep Show all wort

Q: Find the distance

A:

Q: If musS m= So kg & 9- 1o Find requised farce f to just Sturt the mo tion

A:

Q: Determine the resultant mom ent 6+be fig. show n below:

A: Given data Forces acting are 800 N, 200 N

Q: the magnitude q of

A: Given; If principle stresses in a plane stress problem are; σ=200MPa σ=140MPa Acc. to question we…

Q: Q2: Draw the orthographic Projections of given ohject.

A:

Q: Find (ly) for the shaded area

A:

Q: Find the ratio of the speed of the driving shaft to the speed of the driven shaft.

A:

Q: Need to determine the acceleration of of the balloon.

A:

Q: raising both his arms,

A: Raise in center of gravity (h) =7.7887 cm.

Q: уы =3 bafel beared Find the

A: Given data : Modulus of elasticity=E Bulk modulus=K   Required : Poisson ratio

Q: The force applied on the spanner handle while tightening a nut generates Solect ono:

A: When we applied force at a distance from the pivot point then a turning moment has been generated.

Q: Find the wark done Farce = 2 N Displacement = 0.045m

A: Given data : Force=F Displacement=d   Required : Work done

Q: 1/3 sqrt(3) s3

A:

Q: n in the figure. If the drum

A:

Q: Find the Tension of cord AC in N Find the Tension of cord AD in N

A: Given data, Co-ordinates of A = (0,0,0) Co-ordinates of B = (2.5,0,0) Co-ordinates of C =(0,-2,0)…

Q: find the moment

A: Given Data : Moment

Q: Solve for the mobility.

A:

Q: find the requird fillet Size Ch) for figew soンル2 ん。 レン46cm 26cm /2

A: Given data: -  The shear stress for all joints is τ = 0.5 MPa. The length L is L = 40 cm. The…

Q: please show the steps for a) and b)

A: Motion happening in a plane is called motion in two dimensions. Example of two dimension motions are…

Q: Boat is pulléd into a dock by means of a winch 2 meters above the deck of the boat (see figure). The…

A:

Q: Solve for the general solution to the given DE * (т — 2) + m² + 2m – 3 dv -dm = 0

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: its potential energy and speed when the cord makes an angle of 10° with the vertical.

A:

Q: determine P,Q and C

A:

Q: values, and determine (a) the a B.M., and (b) the position

A:

Q: Solve the problem sh

A:

Q: 4. The block had to go up to the circular arc as shown, starting from velocity of 17 m/s at the…

A:

Q: 5 ft 5 ft 12 ft 5 ft reactions in A and D

A:

Q: Bx = ? and By =?  Cx = ? and Cy = ?

A:

Q: Findss 30 kN-m

A:

Q: D.5m/s) find the (H).

A: To find H

Q: برط & Smar SOLVE sve

A:

Q: Find the extension of the plate

A:

Q: . Find the width of the belt used it

A: To find width of belt (b)

Q: Find the tensien force in each 35 eable. A

A:

Q: Find the each force of FAB, FAC and FAD

A:

Q: Q3- Solve the equation for x value :- 1- In e + 4-2log, x - logs 25

A:

Q: Find the sum of the opposite forces

A:

Q: Determine allforte membors- of the trust Shown

A:

Q: Determine C/R for the

A: To determine C/R using block diagram Verify the result using signal flow graph. Topic : Control…

Q: r to the simply sup m shown. What is n lv the maximum be

A:

Q: Please solve the follwoing

A:

Q: ja2 a3

A:

Q: figure below. Decide by calculation whether Over Take Car A after 2 minutes.

A:

Q: The shown system is clutch. O car manual gearbox. O car differential system. O drum brake. O

A: It is a car differential system Option c is correct

Q: Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pr

A: Given Data⇒ Cast iron cylinder Diameter of cylinder(d)=250 mm Pressure (P)=0.7 Nmm2 Maximum tensile…

Q: e. Find the minimum diameter of the wire

A: for safe design stress induced in the rod should be less than or equal to the yield stress. so apply…

Q: Only solve parts D, E and F. I have already solution of A,B and C from bartleby. So dont solve A,B…

A: Given  x(t)=A cos (ωt+ϕ)A=0.045 m ω=15 rad/sec ϕ=pie/8

Q: Find Fi, Fz, Fg magnitude.

A: Write the forces in vector form, F→1=F1×35 j^+F1×45 k^F→1=0.6 F1 j^+0.8 F1 k^F→2=-F2 i^F→3=F3×35…

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.