Find the geometric and hydraulic properties of any real world channel to determine its discharge for a steady-uniform flow using any two methods/Tormulae.
Q: 2. At a certain section of a rectangular channel 10 ft wide, the depth of flow is 2 ft and the flow…
A: Note- We’ll answer the first question since the exact one wasn’t specified. Please submit a new…
Q: An engineer is asked to design a most efficient semi-circular open channel. The channel will have…
A: To determine the radius of the most efficient semi-circular open channel for given flow rate,…
Q: A concrete-lined trapezoidal channel has to be constructed to carry a discharge of 500 cfs. Design…
A:
Q: )A 3 foot diameter culvert has a free discharge and steep slope. The entrance loss coefficient is K.…
A: step1-
Q: A triangular-shaped channel is designed to carry 1.2 cu.m./s of water at a velocity of 0.99 m/s. For…
A:
Q: The depth and velocity of flow in a rectangular channel are 1 m and 1.5 m/s respectively. If the…
A: To determine the velocity of the surge due to the increase in depth of flow. Given, Initial depth…
Q: A trapezoidal canal with side slope of 2 horizontal to 1 vertical is designed to carry 9 cu.m./s at…
A:
Q: Three reservoirs are connected in a common junction. Following are the pertinent information:…
A: Reservior-1ZA=90 mL1=1800 mD1=0.4 mf1=0.02Reservior-2ZB=50 mL2=2000 mD2=0.5…
Q: An engineer makes careful measurements with a weir that monitors a rectangular unfinished…
A: (a) The expression for the normal flow rate. Here, Q is the normal flow rate, A is the cross…
Q: Derive the best efficient (hydraulic) x-section of a triangular, trapezoidal, and rectangular canal.
A:
Q: Q.64 The town of Panipat has a low turbidity raw water and is designing its overflow weir at a…
A: given- overflow rate=180 m3/d/mflow rate=0.6 m3/s
Q: significance of flow over a contracted rectangular weir in hydraulics
A: Given, This question is related to Fluid mechanics/hydraulics The question is : Significance or…
Q: 14.2 In a conduit with a diameter of 4.5 ft, the depth of flow is 4.0 ft. (a) Determine the…
A:
Q: A stable canal is to be designed for a discharge of 30 m/sec with average size of the bed material…
A:
Q: A rectangular channel of width 2 m has a slope of 0.002 and roughness coefficient of 0.012 carries a…
A:
Q: A 6m rectangular channel channel carries a discharge of 30 m³/s at a depth of 2.5m. Determine the…
A: Given, Q=30 m3/sb=6 md=2.5 m
Q: What is the rate of flow in a rectangular channel 4 m wide and 2 m deep with a bed slope of 1 in 900…
A: Given, Wide, b = 4 m Deep, d = 2 m Chezy's constant, C = 50 Bed slope, i = 1/900 = 0.0011
Q: Q4/ Determine the state of flow for the following cases: 1. Rectangular channel with area 4 m²,…
A:
Q: discharge = 2.40 m^3/sec velocity = 1.5 m/sec Given that the rectangular-shaped timber flume…
A:
Q: Calculate the normal depth for a rectangular channel with 4 ft width, 10 cfs discharge rate, 0.03…
A:
Q: 1. Of the various flow measuring devices (Float method, current meter method, use of parshall flume,…
A: Ans1) The maintenance and construction of any stream discharge measurement points constitute a major…
Q: A rectangular sharp-crested weir with end contractions is 1.25 m long. How high should the weir…
A: Given: The length of the weir is 1.25 m. The upstream depth is 2.5 m. The flow rate is 0.5 m3/s.
Q: Read the question carefully and give me right solution with clear calculations. At a certain…
A:
Q: Determine the discharge using the most efficient proportion. Determine the discharge if the side…
A:
Q: 1. If the critical depth of a wide rectangular channel is 3 m, determine the unit flow rate?
A: solution Given critical depth yc=3mts
Q: Calculate the bottom width of a channel required to carry a discharge of 15.0 m/sec as a critical…
A: Given data : Channel=Rectangular channelThe value of discharge throgh rectangular channel Q=15…
Q: A rectangular channel, 16 ft wide, carries a flow of 192 cfs. The depth of water on the downstream…
A: Given- Width (B)=16 ftflow rate (Q) =192 cfsDownstream depth (y2)= 4.2 ft
Q: Develop a conceptual design for a trapezoidal concrete (Gunite, good section) channel that is sized…
A: Normal depth is the depth of flow in a channel when the slope of the water surface and channel…
Q: All the alternate depths and the corresponding energies. 2) The critical flow parameters. 3)…
A: Given, Registration number = 5395 , a = 1 Manning's Coefficient , n = 0.01 Width of the section, b…
Q: Determine the normal flow depth, Froude Number at normal depth and the critical depth for the…
A: Given data: width = 6 m Q=24 m3 /s n=0.012 s=1 in 200
Q: V. Problem Solving 1. A rectangular channel, 20ft wide, carries 400 cfs and discharges onto a 20 ft…
A: as in the Question there are multiple Questions and not interlinked to each other. So as per Our…
Q: Given the following data, calculate a suitable pipe culvert size. Flow = 5 m3/s ; Culvert length =…
A: Solution-Flow(Q)=5m5/sThe culvert length(l)=90m Inlet = 50.0 mThe outlet= 49.0 mThe upstream flood…
Q: A rectangular channel 3 m wide carries 10 m^3/s at a depth of 2 m. Is the flow subcritical or…
A: Find the velocity of flow using continuity equation.
Q: A rectangular channel 60 ft long by 10 ft wide is discharging its flow over 10 ft long suppressed…
A: Given data, Cw = 3.33 Time = 36 sec Length (L) = 60ft Breadth (B) = 10ft L' = 10ft H1 = 1.2ft
Q: The flow characteristics of an open channel do not change with time at any point. Determine this…
A: Given : Flow characteristics of an open channel do not change with time at any point.
Q: In a wide rectangular channel if the normal depth of flow is increased by 15%, determine the…
A: ASKED: To determine the percentage discharge corresponding to a given increase in normal depth of…
Q: What conditions satisfy the maximum discharge and maximum velocity for circular channel.
A: In circular section, the shape of flow cross section varies with the depth of flow. Due to the…
Q: Figure below shows the section of a channel with flood way. Manning coefficient is taken as 0.025…
A: We have to determine the value of discharge as per the given data in the question like the Manning's…
Q: A hydraulic jump occurs on a circular channel with diameter of 15 ft and discharge of Q = 1000 cfs.…
A: Hydraulic jump gradually not graphically...spelling mistake. Hydraulic jump cannot determine…
Q: When you design open channel, which equation you need to use to calculate volume flow rate? Write…
A: To Determine: The equation to calculate the volume flow rate with the explanation of each parameter.…
Q: A right-angled triangular channel symmetrical in section about the vertical carries a discharge of 5…
A: given- Right angled triangular channelDischarge Q=5 m3/svelocity V=1.25 m/s
Q: A rectangular channel carries a discharge of 20 m3/sec with a width of 1 meter and a manning…
A: Using mannings…
Q: A rectangular channel with a width of 9 feet has a discharge of 227 cfs. What is the critical depth?…
A:
Q: Describe what critical depth in an open channel is, and what parameter can be used to evaluate…
A:
Q: Given the following data, calculate a suitable pipe culvert size. Flow = 5 m3/s ; Culvert length =…
A: Solution: Given: Flow = Q = 5 m3 / s culvert length = 90m Waterway invert levels: Inlet = 50.0 m…
Q: tangular weir was incorrectly observed to be 1.93 m. when it was actually 3.53 m. If the crest…
A: Flow over a sharp crested weir is :Q=23Cd2gLH23Incorrect discharge =23Cd2gL1.9323Correct discharge…
Q: A 250 mm cast iron pipe 600 m long carries a discharge of 250 liters/sec. between the two reservoirs…
A: We knowHeadloss= fLQ2A22gdf1=f2L1=L2Q2=2Q1h1=h2
Step by step
Solved in 4 steps with 2 images
- A hydraulic jump occurs in a triangular channel having a side slope of 1H:1V, The flow rate is 0.59 m3/s and the depth before the jump is 0.39m. Compute the height of the jump 1.64 1.46 0.64 0.46What are the four conditions needed for uninterrupted flow? Describe eachDerive dynamic equation of GVF with assumptions and physical meaning. How do Gradually Varied Flow occurred in open channel?
- For an approach flow in a rectangular channel with depth of 2.0 m and velocity of 2.2 m/s, 1) determine the depth of flow over a gradual rise in the channel bottom of ∆? = 0.25 m; 2) repeat the solution for ∆? = 0.5 m.Determine the normal depth of a flow in a concrete lined rectangular channel 20.0M wide carrying 150m3/s with a bed slope of 0.0025 and Manning'"s n of 0.016,assuming the channel can be considered as wideA 10-m wide rectangular channel is to carry 44 m3/s with a uniform depth of 3 m. The channel is lined with concrete, for which n is 0.014. a. What is the slope of this channel, and what is the drop in elevation per kilometer? b. If the flow in the channel were to decrease to 22 m3/s, all other data (including slope and n) being the same, what would be the depth of water?
- Find the critical depth of flow for a trapezoidal channel with a bottom width of 8 m, and a side slope of 1.2H:1V. It carries a flow of 50 m3/s. using the specific eneergyDetermine the discharge in MLD of a 2800 mm gravity flow concrete aqueduct with a hydraulic gradient of 0.0015. Assume pipe is flowing full with a coefficient of roughness = 0.015. Answer in whole number only.A trapeziodal channel lined with grass (n = 0.027) has a bottom width of 4.25 feet, side slopes of 2 horizontal to 1 vertical, and a slope of 1.1 percent. Water is flowing at a depth of 2.35 feet. a) what is the discharge? b) what is the velocity?
- Answer Fast For a rectangular channel 5 m wide carrying a flow of 15 m3/s, determine the critical depth and the critical velocity.The flow through a rectangular channel (width in x and height in z) is nonuniform in the z-dimension, with a velocity profile of V(z) = 3z and a zero velocity at the bottom of the channel. If the channel is 2m wide and has a height of 5m, what is the flowrate of water in this channel in m3/s?A triangular channel has a vertex angle of 90o and carries a flow at critical depth of 0.3m. The discharge in the channel is? (a) 0.11 m3/s (b) 0.21 m3/s (c) 0.31 m3/s (d) 0.41 m3/s